不同碳黑填料含量2D—SiCf／SiC复合材料介电及雷达吸波性能研究

对先驱体浸渍裂解工艺(PIP)制备的含碳黑填料2D-SiCf/SiC复合材料介电以及雷达吸波性能进行研究.研究表明,由于KD-Ⅰ型SiC纤维表面具有连续碳涂层,不能直接用于吸波材料,需通过空气热处理手段将其除去.对纤维表面去碳后制成的不同碳黑填料含量2D-SiCf/SiC复合材料微波介电常数进行测试,结果表明,随碳黑含量增加,复合材料介电常数明显增大,但由于碳黑的高比表面和先驱体溶液粘度的限制,复合材料中碳黑体积分数最大仅能达到7%～8%,介电常数难以继续增大,介电损耗低于0.3,并且介电常数频散效应不理想.对不同碳黑填料含量复合材料反射率进行计算,结果表明,单层复合材料在某一频段内具有较好的吸波性能,但由于复合材料介电常数频散效应较差,宽频吸波性能不理想,采用不同吸收剂含量复合材料层铺工艺可能可以解决吸波性能带宽问题.     

SiO2f/SiO2复合材料自身及其与铜、不锈钢的钎焊

采用AgCuTi活性钎料,在880℃/10min规范下成功实现了SiO2f/SiO2自身、SiO2f/SiO2与Cu和SiO2f/SiO2与1Cr18Ni9Ti三种接头的连接。实验结果表明,三种接头中靠近SiO2f/SiO2母材的界面处均形成了一层薄薄的扩散反应层组织,反应层中出现了Ti和O的富集,根据两者的原子比例推断生成了TiO2相;另外,三种接头中心区都形成了由灰色相和白色相共同组成的Ag-Cu共晶组织,其中灰色相为Cu基固溶体,白色相为Ag基固溶体。接头剪切强度结果显示,SiO2f/SiO2/Cu接头剪切强度为12.4MPa,SiO2f/SiO2/1Cr18Ni9Ti接头剪切强度为18.4MPa,接头中的残余应力是决定接头强度大小的重要因素之一。     

2D C/SiC-ZrB2复合材料的烧蚀性能

用ZrB2微粉对2D C/SiC基体进行改性,研究了化学气相渗透结合浆料浸渍及先驱体浸渍裂解工艺制备2DC/SiC-ZrB2复合材料在氧-乙炔焰和1800℃甲烷风洞环境中的烧蚀行为.结果表明:在氧-乙炔环境中,2D C/SiC-ZrB2的线烧蚀率和质量烧蚀率分别为6.1×10-2 mm/s和1.0×10 -2g/s,相对2D C/SiC复合材料而言,ZrB2微粉并没有提高C/SiC复合材料的抗烧蚀性能.在1800℃甲烷风洞环境中,涂层致密度起主要作用,涂层致密度相同时,复合材料的开气孔率越大,质量烧蚀率越大,ZrB2微粉的渗入对C/SiC复合材料的烧蚀性能影响不大.     

民间非营利组织财务治理问题探讨

非营利组织是政府和企业之外的第三部门,其使命在于向社会提供公共物品与服务,使得社会效益最大化。在探讨民间非营利组织财务治理概念基础上,比较分析了财务治理、内部控制与组织目标的关系,通过分析非营利组织的特征,展开财务治理问题的逻辑推演,然后对我国民间非营利组织财务治理的现状及存在的问题进行了探讨,从内部控制的视角提出相应的财务治理对策。非营利组织的财务治理不应仅仅从控制的角度来考虑,更应从引导的角度出发。     

基于相对导航的多平台INS误差联合修正方法

在机群协同编队飞行中,编队成员仅装载惯性导航系统(INS)的方式具有隐蔽、抗干扰等明显的优势,但随着航时的增加,INS误差将不断累积.使导航系统失效,为此,提出基于相对导航的多平台INS误差联合修正方法.首先,建立了编队成员相对导航运动模型及非线性观测模型,采用量测重构技术构造了伪线性观测模型并推导了观测噪声协方差矩阵...     

Tear Resistance of Orthogonal Kevlar-PWF-reinforced TPU Film

This work seeks to investigate the notch sensitivity and fracture behaviour of orthogonal Kevlar-plain woven fabric (PWF)-reinforced thermoplastic polyurethanes (TPU) film applied to high altitude balloon. Four types of specimens are implemented to measure notched strength and fracture toughness by conducting static tension and tear tests on an MTS system respectively. The damage and failure mechanisms are discussed and the results for notched strength and tear resistance are evaluated and compared with each other. From the experiments, it is found that the notch sensitivity of the film increases with the increase in the size of the hole, but the notch sensitivity and the stress concentration of the notch are insignificant and there is a decrease of only about 4%-10% in tensile strength for the notched specimens with different hole sizes in diameter compared with the unnotched specimen. In contrast, the tear resistance containing a central slit with only 1 mm length is about half of tensile strength of the unnotched film, which implies that the tear resistance exists an significant notch sensitivity. The results of this study provide an insight into notch sensitivity and fracture behaviour of the Kevlar-PWF-reinforced TPU film and constitute a fundamental basis for the design of high altitude balloon.     

A novel virtual material layer model for predicting natural frequencies of composite bolted joints

A novel virtual material layer model based on the fractal theory was proposed to predict the natural frequencies of carbon fiber reinforced plastic composite bolted joints. Rough contact surfaces of composite bolted joints are modeled with this new proposed approach. Numerical and experimental modal analyses were conducted to validate the effectiveness of the proposed model. A good consistence is noted between the numerical and experimental results. To demonstrate the necessity of accurately modeling the rough contact surfaces in the prediction of natural frequencies, virtual material layer model was compared with the widely used traditional model based on the Master-Slave contact algorithm and experiments, respectively. Results show that the proposed model has a better agreement with experiments than the widely used traditional model (the prediction accuracy is raised by 8.77% when the pre-tightening torque is 0.5 N∙m). Real contact area ratio A* of three different virtual material layers were calculated. Value of A* were discussed with dimensionless load P*, fractal dimension D and fractal roughness G. This work provides a new efficient way for accurately modeling the rough contact surfaces and predicting the natural frequencies of composite bolted joints, which can be used to help engineers in the dynamic design of composite materials.     

发散磁场中等离子体加速和推进性能数值研究

稳态螺旋波等离子体推力器中,源室放电获得的一定能量的等离子体经过磁喷管加速产生预定的推力和比冲。为了分析在发散磁场约束下,等离子体的运动受约束磁场和内能变化的影响规律及其推进性能,引入了考虑电子和离子不同响应的二维轴对称数值模型。计算了入口中心磁感应强度[B0]为100～500G、电子温度[Te0]为3.0～10.0eV时等离子体的运动。结果表明,入口等离子体的内能增加,[B0]保持100G不变时,其最终膨胀的绝对速度增加,比冲从400s提高到约为580s;内能变化对比冲[Isp]的影响大于磁感应强度。不考虑等离子体与磁场相互作用情况下,文中计算的磁场范围可以最大限度地将内能转化为等离子体的轴向定向动能;为了提高[Isp],应适当增加电离段等离子体获得的能量,且可以适当降低对产生约束磁场的电流线圈输入能量要求。     

直缝式等离子体合成射流激励器特性的实验研究

为了研究一种新型的直缝式等离子体合成射流激励器,采用高速纹影技术和电参数测量的方法,对激励器的瞬态流场特性和放电特性进行了研究。实验结果表明:在相同出口面积的情况下,直缝式等离子体合成射流激励器的初始射流速度是直孔式激励器的1.4倍。直缝式激励器速度衰减更快,喷气时间更短,和外部气流的动量交换更加迅速。实验中首次对直缝激励器的三维流场进行描述及分析,发现其前驱激波及射流形态具有更好的平面度,存在较大的均匀区。直缝式等离子体合成射流激励器在提高工作频率、扩大流动控制区间等方面具有一定优势。     

折叠翼变体飞行器非定常气动特性实验研究

折叠翼变体飞行器是一种可以在飞行中改变自身气动外形的新型飞行器。研制出了一种折叠翼变体飞行器的风洞实验模型,在风洞实验中测得了模型不同变体位置下的气动力以及进行变体运动时气动力的动态变化过程,并通过PIV实验手段获得模型周围的流场在变体运动过程中的变化情况。结果表明：在机翼变形过程中,折叠翼模型有明显的非定常气动现象产生,而且折叠变形的速度越大,非定常现象越明显。出现非定常现象的主要原因是变体运动对机翼前缘涡的影响。