考虑高斯能量分布的复杂表面航天器激光雷达散射特性分析

针对复杂表面航天器在激光雷达照射下散射特性模拟不准的问题,通过表面建模和激光特性修正进行了解决。该方法首先通过高斯能量分布法对激光光束模型进行修正;然后基于有限元的思想,针对航天器复杂表面非光滑、非连续以及多材质等特性,利用改进Z-buffer的消隐算法解决了复杂航天器表面建模问题;最后建立了面向激光雷达的复杂表面航天器激光雷达散射截面的计算方法。仿真分析表明:航天器不同姿态下的激光雷达散射截面精度提升了14.58%,为后续面向激光雷达的隐身设计奠定了基础。     

微小刀具同轴全息对刀方法研究

针对现有对刀方法存在的各种不足,提出了一种微小刀具的同轴全息对刀方法.在对全息成像原理和全息图像关键问题进行研究与分析的基础上,搭建了一套微细铣刀的全息对刀检测装置,并利用标准刀具在五轴加工中心进行了微细铣刀的对刀测量试验.试验结果表明:该对刀装置能够高效地进行微细铣刀的对刀检测,系统相对检测精度达5.1μm.在相同检...     

A novel virtual material layer model for predicting natural frequencies of composite bolted joints

A novel virtual material layer model based on the fractal theory was proposed to predict the natural frequencies of carbon fiber reinforced plastic composite bolted joints. Rough contact surfaces of composite bolted joints are modeled with this new proposed approach. Numerical and experimental modal analyses were conducted to validate the effectiveness of the proposed model. A good consistence is noted between the numerical and experimental results. To demonstrate the necessity of accurately modeling the rough contact surfaces in the prediction of natural frequencies, virtual material layer model was compared with the widely used traditional model based on the Master-Slave contact algorithm and experiments, respectively. Results show that the proposed model has a better agreement with experiments than the widely used traditional model (the prediction accuracy is raised by 8.77% when the pre-tightening torque is 0.5 N∙m). Real contact area ratio A* of three different virtual material layers were calculated. Value of A* were discussed with dimensionless load P*, fractal dimension D and fractal roughness G. This work provides a new efficient way for accurately modeling the rough contact surfaces and predicting the natural frequencies of composite bolted joints, which can be used to help engineers in the dynamic design of composite materials.     

AZ31B变形镁合金激光-MIG复合焊焊接组织和性能分析

采用激光-MIC复合焊对10mm厚的AZ31B变形镁合金进行焊接.利用光学显微镜、扫描电镜、X射线衍射仪等手段分析了焊接接头的外观和截面特征、显微组织、元素分布、焊缝物相和断口形貌等,并检测了接头区域硬度和接头强度.试验结果表明:采用激光-MIG复合焊能获得成形美观的焊缝,无明显的缺陷;焊缝热影响最大宽度位于激光区,约为100μm,焊缝组织为15～25μm的等轴晶粒;相比于母材,焊缝区的镁元素出现烧损,铝和锰元素的比例有一定增加;焊缝区主要为Mg,Al和少量的MgO相.焊接接头硬度值较均匀;焊缝抗拉强度达到222MPa,断口形貌为混合断裂断口.     

一种基于LabVIEW的航空电缆断路故障检测系统

利用LabVIEW软件开发平台设计和研制的一种航空电缆断路检测系统,可完成数据库查询、数据分析、结果显示和存储。利用工控机中的电缆资料数据库,再结合检测电路等相应的硬件,该系统即可自动给出断开电缆的连接关系。应用表明,该系统可快速检测出损伤电缆的连接关系,检测结果准确、可靠。     

温度对磁屏蔽霍尔推力器磁场构型的影响研究

霍尔推力器磁路设计主要通过常温静态磁场仿真得到，并实测推力器非工作状态常温磁场进行复核。大功率霍尔推力器将面临更为严峻的热问题，推力器工作时磁路系统受高温影响，因此在常温下仿真得到的磁场位形会因温度升高而产生偏移，不能反映推力器真实工作时的磁场情况。为研究霍尔推力器工作时热量对磁路系统的影响，通过热磁耦合仿真对10kW磁屏蔽霍尔推力器的热态磁场分布进行研究，并对热态、常温仿真结果进行了对比，发现在阳极附近的径向磁感应强度Br的差异比放电室出口更大。常温设计的磁屏蔽构型在热态时偏离磁屏蔽，磁场和壁面最大不符合度达到13%，通过陶瓷出口型面修正后重新获得磁屏蔽效果，使最大不符合度降低到4.8%以下。合理热设计有助于降低热载荷，热仿真得到磁路系统最高温度低于500℃，低于0.78倍的居里温度Tc磁性急剧转变点，不会出现磁性能急剧下降，但热量对磁屏蔽霍尔推力器磁场构型的影响是应该考虑的。     

Multiple hierarchy risk assessment with hybrid model for safety enhancing of unmanned subscale BWB demonstrator flight test

To explore the low-speed characteristics of the Blended-Wing-Body (BWB) configuration for future civil aircraft, a series of unmanned subscale demonstrators have been developed and tested by our research team. During this process, specific safety risks deriving from uncertain design features, system unreliability, and insufficient personnel experience caused continuous flight test mishaps and the risk mechanism was not clear. Local and trial-and-error learning driven safety improvements took few effects on mishap prevention, so our focus was turned to look for systematic safety strategies. This paper establishes a systems theory based hybrid model to integrate the physical system reliability analysis techniques with the system dynamics method for illustrating the multiple risk interactions of the demonstrator flight test involving organizational, human resource and technical system factors. Using the prior BB-5 demonstrator as a case, the hybrid model simulation represents its historical risk evolution process, which verifies the model rationality. Derived risk control strategies reduced the mishap rate of a new demonstrator called BB-6 Sprit. The paper also shows the extended hybrid model can be applied on safety management of unmanned aerial vehicles from the initial period of vehicle development.     

可靠性信息在直11型机功能-可靠性适航审定中的应用

在直11型机的适航审定时，按CCAR25．15(二)的要求，要进行功能-可靠性飞行试验，以验证该机是否满足CCAR27．1301(d)和CCAR27．1309(a)的要求。本文基于直11型机外场收集的可靠性信息，论述了该机的功能-可靠性与条例要求的相符性，从而把CCAR21所要求的功能-可靠性飞行验证时间减少为38小时，显然，这将减少飞行试验时间，加快试验进度，为今后用可靠性信息来验证新研直升机的功能-可靠性与适航条例要求相符性提供了合适的方法。     

“X”型探针测量三维速度的新方法

利用热线侧角对风速测量的影响提出了在平面内将“Ｘ”型探针旋转４５°来测量三维速度的新方法，通过数学推导获得了分解三维平均速度和脉动速度的数学计算式，并且在标准风洞上进行了实验验证。