热力学排气系统中节流效应及其冷量利用分析

为更好地理解热力学排气系统(TVS)的运行机理，优化其运行参数，针对节流装置，建立了热力学模型，讨论了节流过程中状态参数的变化规律，对比了单相气体、单相液体节流的性能特性，进一步揭示了焦汤节流效应的原理，分析了不同节流背压下节流前低温工质(液氢和液氧)压力和温度对节流性能的影响，并结合TVS实际应用，阐述了节流最大制冷量的利用效果，提出了优化的TVS工作区间。研究表明：在节流过程不发生相变情况下单相气体节流制冷效应要比单相液体节流制冷效应更加显著；而在节流过程发生相变情况下液体节流至两相后，由于空化吸热导致流体温度降低，对于液氢，0.5MPa的压降可产生接近3 K的温降。对于液体节流，节流前压力对节流过程影响可忽略，〖JP2〗而节流前温度和节流背压对节流过程起主导作用；对于液氢在在轨运行工况下，考虑到节流制冷量的充分利用，同时保证换热过程体积含气率不高于90%，推荐TVS系统中节流背压范围为75～143 kPa。     

LENS风洞试验返回器模型气动热特性模拟

国家数值风洞高超声速流动模拟软件HyFLOW的研制对打破国外同类软件的技术壁垒具有重要意义。与国外DPLR软件进行了对比研究，同时系统介绍了HyFLOW软件求解器的数值方法、物理化学模型以及壁面催化特性计算模型等主要方法，采用典型算例对有限催化模型进行了数值验证，最后基于LENS风洞试验146 mm返回器标模外形开展了高超声速气动热特性数值模拟。研究结果表明，HyFLOW软件在高超声速热化学非平衡流动模拟与评估方面的气动力计算精度高，与国外同类软件DPLR相当，同时其壁面催化条件下的气动热计算精度可靠，可信度高。     

黄渤海晴空像元下雾霾识别的机器学习算法

为实时有效地识别和监测雾霾，选取2013年10月4日与10月5日的两景MODIS遥感图像，利用不同类型像元的光谱差异，基于神经网络模型，建立海上雾霾的遥感识别机器学习算法。经检验表明，在晴空条件下，机器学习算法反演精度相对较高，已超过98%，利用算法可以实现对中国近海上空雾霾的监测。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.     

Availability modeling for periodically inspection system with different lifetime and repair-time distribution

Availability is a main feature of design and operation of all engineering system. Recently,availability evaluation of periodical inspection systems with different structures is at the center of attention due to the wide application in engineering. In this paper, an analytical and probabilistic availability model for periodical inspection system is proposed by a new recursively algorithm,which can achieve limiting average availability and instantaneous availability of periodical inspection system under arbitrary lifetime and repair-time distributions. Then three application examples are presented, the systems lifetime and repair-time are respectively fellow exponential/exponential,Weibull/normal and Weibull/lognormal distribution. Finally, a Weibull/lognormal system is studied to analyze the dynamic relationship between inspection period and availability. The results indicate that the proposed approach can provide the technology support for improving system availability and determining reasonable inspection period.     

热处理对FeCo-2V-0.5Cr软磁合金力学与磁学性能的影响

针对FeCo-2V-0.5Cr软磁合金,研究了真空热处理时间对其微观组织结构、力学与磁学性能的影响规律,发现在800℃下热处理时间为2h左右时,合金的抗拉强度和延伸率达到最佳,同时仍保持良好的软磁性能,抗拉强度、延伸率以及矫顽力分别为867.8MPa、10.4%以及2.0Oe。进一步对该合金进行附加磁场下的真空热处理,重点研究了合金的交流损耗与矫顽力随附加磁场方式包括磁场撤除温度与磁场下保温时间的变化规律,发现适当的磁场热处理对合金相关力学性能影响不大,但由于合金中产生了单轴各向异性而使合金矫顽力进一步降至1.6Oe。     

舰载机着舰中侧风和常值甲板风的影响研究

舰载机要安全着舰,需要精确控制全着舰航线轨迹及其稳定性,风是影响舰载机着舰航线的主要因素。论文主要研究了侧风和常值甲板风对舰载机着舰飞行产生的影响,建立了影响舰载机着舰飞行的不同侧风、甲板风的数学模型。根据数学模型计算了不同甲板风和侧风下着舰飞行轨迹参数,从而提出了着舰飞行修正方法。     

8mm Dicke辐射计波形仿真研究

采用System view软件对从输入到天线的噪声信号到A/D采样之前的各个模块和辐射计线性度进行了波形的仿真研究,仿真结果和实际相符合,对辐射计的硬件实现提供了很好的指导作用。