可控曲率半径的圆柱形叶片逐点绘型方法

针对中低比转速离心泵,根据叶片进出口边界条件,以逐点绘型方法为基础,提出了一种新的曲率半径可控的叶片绘型方法。该方法的主要特点是曲率半径比值可作为设计常量由设计人员根据需要事先给定,随后分析了曲率半径及比例因子对叶片安放角、叶片包角、相对速度及速度矩等的影响。结果表明,不同曲率半径比值下的叶型参数及流动参数变化范围很大,曲率半径比值较大时,节流损失较大,泵扬程较低,曲率半径比值较小时,脱流损失较大,泵效率较低,存在较优的曲率半径比值区间[1.4,2.4],使叶片安放角平滑变化,泵的综合性能较优,在该优化区间内,取较大的曲率半径比值有利于获得较优的汽蚀性能,比例因子为0时叶片安放角的变化较为平稳,可用于开展离心泵的初步设计。     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

“三美论”下的《红楼梦》“雪景联诗”两英译本赏析

许渊冲教授提出的"三美"翻译理论对于诗歌翻译具有重要的指导作用。从"三美"原则出发,分别以Hawks David及杨宪益、戴乃迭的《红楼梦》译本中"雪景联诗"为研究对象,通过对比分析探讨其得与失,旨在为中国古典诗歌翻译提供一些可供借鉴的方法。     

均匀各向同性大气湍流对声爆传播特性的影响

基于离散Fourier模态有限和生成的随机大气湍流场，采用修正波形参数方法，开展了均匀各向同性大气湍流对典型超声速客机声爆传播特性的影响分析。计算采用的超声速客机模型为自行生成的简化超声速公务机模型。首先，应用航空工业空气动力研究院自主研制的CFD软件ARI_Overset在三维空间求解Navier-Stokes方程，得到作为声爆远场传播初始值的近场空间压力分布；其次，基于Von Karman能量谱，采用离散Fourier模态有限和形式生成随机均匀各向同性大气湍流场；最后，采用修正波形参数方法模拟了声爆信号在随机速度湍流场中的传播过程。数值结果表明：各向同性大气湍流对于地面声爆特征有重要影响。与无湍流状态相比，均匀各向同性大气湍流使得地面声爆特征增强的概率约为55%，使得地面声爆特征减弱的概率约为45%，故总体而言大气湍流效应更倾向于增强地面声爆特征；均匀各向同性大气湍流对于声爆传播路径影响相对较小，但是这一变化仍会导致地面信号接收点的不确定性。     

热力学排气系统中节流效应及其冷量利用分析

为更好地理解热力学排气系统(TVS)的运行机理，优化其运行参数，针对节流装置，建立了热力学模型，讨论了节流过程中状态参数的变化规律，对比了单相气体、单相液体节流的性能特性，进一步揭示了焦汤节流效应的原理，分析了不同节流背压下节流前低温工质(液氢和液氧)压力和温度对节流性能的影响，并结合TVS实际应用，阐述了节流最大制冷量的利用效果，提出了优化的TVS工作区间。研究表明：在节流过程不发生相变情况下单相气体节流制冷效应要比单相液体节流制冷效应更加显著；而在节流过程发生相变情况下液体节流至两相后，由于空化吸热导致流体温度降低，对于液氢，0.5MPa的压降可产生接近3 K的温降。对于液体节流，节流前压力对节流过程影响可忽略，〖JP2〗而节流前温度和节流背压对节流过程起主导作用；对于液氢在在轨运行工况下，考虑到节流制冷量的充分利用，同时保证换热过程体积含气率不高于90%，推荐TVS系统中节流背压范围为75～143 kPa。     

LENS风洞试验返回器模型气动热特性模拟

国家数值风洞高超声速流动模拟软件HyFLOW的研制对打破国外同类软件的技术壁垒具有重要意义。与国外DPLR软件进行了对比研究，同时系统介绍了HyFLOW软件求解器的数值方法、物理化学模型以及壁面催化特性计算模型等主要方法，采用典型算例对有限催化模型进行了数值验证，最后基于LENS风洞试验146 mm返回器标模外形开展了高超声速气动热特性数值模拟。研究结果表明，HyFLOW软件在高超声速热化学非平衡流动模拟与评估方面的气动力计算精度高，与国外同类软件DPLR相当，同时其壁面催化条件下的气动热计算精度可靠，可信度高。     

黄渤海晴空像元下雾霾识别的机器学习算法

为实时有效地识别和监测雾霾，选取2013年10月4日与10月5日的两景MODIS遥感图像，利用不同类型像元的光谱差异，基于神经网络模型，建立海上雾霾的遥感识别机器学习算法。经检验表明，在晴空条件下，机器学习算法反演精度相对较高，已超过98%，利用算法可以实现对中国近海上空雾霾的监测。     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.