Pro/CABLING三维布线实践

PRO/CABLING三维布线是数字化样机设计过程中的重要组成部分。结合操作实践,介绍了PRO/CABLING三维布线的主要流程、基本概念和关键步骤的解决方法,从而为构筑高质量数字化样机提供一些借鉴和思路。     

Global ionospheric scintillations revealed by GPS radio occultation data with FY3C satellite before midnight during the March 2015 storm

Global observations of S4 amplitude scintillation index by the GPS Occultation Sounder (GNOS) on FengYun-3 C (FY3C) satellite reveal global dynamic patterns of a strong pre-midnight scintillations in F-region of the ionosphere during the St. Patrick’s Day geomagnetic super storm of 17–19 March 2015. The observed strong scintillations mainly occurred in the low latitudes, caused by equatorial plasma bubbles. During the main storm phase (March 17), the scintillations were first triggered in the New Zealand sector near 160°E longitudes, extending beyond 40°S dip latitude. They were also enhanced in the Indian sector, but significantly suppressed in East Asia near 120°E longitude and in Africa around 30°E longitude. During the initial recovery phase (March 18–19), the global scintillations were seldom observed in GNOS data. During the later recovery phase (after March 19), the scintillations recovered to the pre-storm level in Indian, African, and American sectors, but not in East Asian and any of Pacific sectors. These results closely correlate with observations of the density depletion structures by the Communication/Navigation Outage Forecasting System (C/NOFS) satellite, and ground-based instruments. Such consistency indicates reliability of our scintillation sensing approach even in a case-by-case comparison study. The prompt penetration electric field and disturbance dynamo electric field are suggested as the main factors that control the enhancement and inhibition of the scintillations during the storm, respectively.     

基于瞬态液晶测量技术的收缩-扩张形孔

采用一种进行全表面测量的瞬态液晶测量技术测量了新型气膜孔(收缩-扩张形孔)的气膜冷却特性,研究了动量比对冷却效率和换热系数的影响,并与传统的圆柱形孔气膜冷却特性进行了对比,结果表明:收缩-扩张形孔中心线附近区域的冷却效率相对较低,而两孔之间区域的冷却效率相对较高,与圆形孔分布规律相反;在上游区域,两孔中间区域的换热系数比相对孔中心线附近区域较高,而在下游区域,两孔中间区域的换热系数比相对孔中心线附近又较低,与圆形孔相比也有较大不同。相对于圆柱形孔,收缩缝形孔的平均换热系数比在上游较高,在下游较低;收缩-扩张形孔喷出气膜对下游壁面区域的有效覆盖率远大于圆柱形孔,其展向平均冷却效率明显高于圆柱形孔;收缩-扩张形孔在动量比为2时的平均冷却效率最高。     

涡轮盘多轴低循环疲劳寿命可靠性分析

多轴低循环疲劳是航空发动机涡轮盘的主要失效模式,应用多轴疲劳寿命预测的等效应变模型和临界面模型对某涡轮盘中心孔的疲劳寿命进行了预测,并与试验寿命进行了对比,得出等效应变模型预测结果均偏于危险,并且误差较大,而临界面模型误差较小,尤其拉伸型破坏的SWT模型误差在10%以内。进一步选取SWT模型进行了涡轮盘的寿命可靠性分析,鉴于多轴疲劳试验复杂、费用高并缺少统计数据,利用现有单轴疲劳试验数据将疲劳性能参数表示为标准正态随机变量的函数,将SWT模型随机化建立多轴疲劳寿命概率模型,得到可靠度0.998 7的涡轮盘寿命,与试验估计给出的技术寿命较为接近。     

Alford力和滚动轴承对轴流压缩机转子系统动力特性和稳定性的影响

 研究叶尖气隙和滚动轴承共同作用下轴流压缩机的非线性动力特性及稳定性。采用有限元法和非线性滚动轴承模型,建立压缩机转子系统动力学模型,其中转子旋转时非均匀分布叶尖气隙引起的气动失稳力(即Alford力)根据已有实验数据和计算模型求得。通过计算分析发现叶尖气隙和滚动轴承分别激起系统的反进动和正进动共振频率,其共同作用造成压缩机转子系统的失稳,很好地解释了已有实验中出现的失稳现象。表明滚动轴承反力和Alford力的共同作用对压缩机转子系统的动力性能和稳定性有显著影响。     

镍基单晶蠕变研究：基于晶体塑性的蠕变模型

在镍基单晶合金高温蠕变建模工作的第二部分,通过提出的蠕变材料模型,在晶体塑性理论的变形梯度与滑移系剪切应变率关系的基础上结合不同温度下不同滑移系上的蠕变机理,最终建立起滑移系上行为与材料结构变形的联系。材料本构方程的积分采用了四阶Runge-utta法,并通过对DD3和 CMSX-4两种材料在不同温度,晶体取向和应力水平下的试验曲线进行计算模拟,说明了模型及算法的可行性及对较宽的温度、应力和晶体取向下蠕变行为模拟的能力。     

纤维单向缠绕制备C/C扩张段成型技术

在"锥形体纤维单向缠绕技术"的基础上进行了碳纤维单向缠绕制备C/C扩张段成型工艺的探索,制备出了Φ180 mm C/C扩张段试验件,并对其进行了性能测试及整体探伤.测试结果为:超声探伤分贝差为15 dB的缺陷面积小于5%;沿母线方向层间剪切强度大于10 MPa,大端环向层间剪切强度偏小;内压爆破压强为0.6 MPa,破裂模式较好.试验结果表明,采用碳纤维单向缠绕技术制备C/C扩张段工艺可行.     

利用多普勒原理测量微机电系统中微结构的动态特性

介绍了将显微扫描激光多普勒测振仪与基础激振法相结合的微结构动态特性的非接触无损测量方法、扫描激光多普勒测振仪的工作原理、设计的基础激振器及其驱动信号.并给出典型微结构--微悬臂梁的测量结果.测量结果与理论计算及有限元仿真结果相符,验证了该方法的有效性.     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

一种临近空间升浮一体飞行器气动布局设计研究

应用理论方法和数值模拟方法开展升浮一体太阳能无人机气动布局设计研究,通过优化选形设计获得高升阻比气动布局,对比两种方法的计算结果以及分析存在差别的原因;应用张线天平支撑风洞试验测试技术,对设计布局开展实验验证研究,建立大展弦比的双机身气动布局风洞试验测试方法,分析了不同雷诺数下实验模型的纵向和横向气动特性影响。研究结果表明:风洞试验结果与设计结果吻合良好,验证了设计结果的可靠性,获得了对总体设计具有指导意义的结论和试验数据结果。