Simulation and Analysis of Electromagnetic Force in Laser Melting Deposition by Electromagnetic Impact

Magnetic field was introduced in laser melting deposition to reduce the pores in workpieces.Finite 3-D model of the coil-deposition layer-substrate was established.Simulation results show that the electromagnetic force in deposition layer mainly concentrates in the projection area of the coil.Axial electromagnetic force shows repulsion in one cycle.The experimental results indicate that the magnetic field is beneficial for grain refinement,microhardness increasement and decline of quantities and average sizes of pores.     

Performance evaluation for MAP state estimate fusion

This paper presents a quantitative performance evaluation method for the maximum a posteriori (MAP) state estimate fusion algorithm. Under ideal conditions where data association is assumed to be perfect, it has been shown that the MAP or best linear unbiased estimate (BLUE) fusion formula provides the best linear minimum mean squared estimate (LMMSE) given local estimates under the linear Gaussian assumption for a static system. However, for a dynamic system where fusion is recursively performed by the fusion center on local estimates generated from local measurements, it is not obvious how the MAP algorithm will perform. In the past, several performance evaluation methods have been proposed for various fusion algorithms, including simple convex combination, cross-covariance combination, information matrix, and MAP fusion. However, not much has been done to quantify the steady state behavior of these fusion methods for a dynamic system. The goal of this work is to present analytical fusion performance results for MAP state estimate fusion without extensive Monte Carlo simulations, using an approach developed for steady state performance evaluation for track fusion. Two different communication strategies are considered: fusion with and without feedback to the sensors. Analytic curves for the steady state performance of the fusion algorithm for various communication patterns are presented under different operating conditions.     

中山植物园植物定植图微机显示与管理系统

首先指出利用微机管理植物园取代落后的手工管理的意义。进而介绍了植物定植图微机显示与管理系统的具体实现途径，并描述了能将地图（含充色地图）、植物、宇符等录入。绘出，以及对植物进行检索显示等主要功能。     

线性有源网络拓扑分析的k-连接组法

本文提出了Coates图k-连接组的概念,建立了求解线性有源网络不定导纳矩阵一般k阶余因式的k-连接组拓扑公式,得到了线性有源网络拓扑分析的一种新方法——k-连接组法。与正(负)根有向树法相比,这种方法需找的子图和结果中的冗余项都比较少。     

正态分布可靠寿命经典近似限的改进

本文给出了正态分布可靠寿命的又一个经典近似下限，经验证，本文所给出的结果的精度比已有的结果精度要高，可提供给可靠性工程人员使用。     

GPS空间分集接收机

为解决传统单天线GPS接收机在载体旋转情况下不能连续跟踪卫星连续定位和速度偏差较大的问题,提出一种GPS空间分集接收机设计方案。该接收机采用空间分集算法和消旋解算方法,能稳定连续地跟踪GPS卫星信号,并准确地求解出载体的平动速度。     

AP复合固体推进剂燃烧模型

本文提出了一个复合固体推进剂的综合燃烧模型和相应的数学处理方法。该模型对凝聚相反应作了更细微的分析,特别重视和强调了各种热量传递对燃烧所起的作用,并以推进剂中处于连续相的粘合剂线性分解速度表示推进剂的线性燃速。根据此模型编制程序并进行了大量计算。计算结果与实验符合得很好。对AP/HTPB多级配推进剂的计算结果中,相对误差小于10％的占80％,对Ae/AP/HTPB推进剂则占90％以上。     

基于小波分解与分形内插相结合的地形数据压缩方法

地形匹配制导中需要使用大量的地形数据，因此有效的地形数据压缩技术是非常重要的。传统的地形数据压缩方法主要采用线性内插的方法，但这对于地形起伏较大的山区地形失真太大，不能满足高精度导航的要求。本文基于小波分解与分形内插相结合的方法，提出了一种新的地形数据压缩方法，它具有压缩比高，保真性好，解码快的特点，特别适合山区地形数据的压缩。     

弹性机翼对机载导弹子惯导系统导航精度的影响分析

弹性机翼的振动及杆臂效应会引起机载导弹加速度计输出中的附加干扰加速度，从而引起导弹子惯导系统的导航参数误差。本文通过建立机翼弹性振动模型及惯导误差传播模型，从理论上分析了机翼弹性振动及杆臂效应对子惯导系统导航精度的影响，并进行了计算机仿真研究。     

冲击响应谱计算相关参数选择的研究

国军标GJB2238A-2004《遥测数据处理》的附录K对冲击响应谱的计算方法和阻尼系数做了明确规定, 但未明确其它参数如何选择。文中以半正弦波的冲击响应谱为例,导出了冲击响应谱分析时选择其它相关参数的原则。