金属图象分割的研究

结合金属图象的特点,利用传统阚值分割技术和基于最大熵原则的图象分割技术对金属图象分割进行了分析;并根据金属图象分析要求,提出了先二值化金属图象再进行边缘提取的方法.对比实验结果表明,基于最大熵原则的图象分割技术可以获得较好的分割效果,所提出的方法能够获得连续闭合的晶粒边缘,为下一步的金属图象分析提供了可靠的依据.     

多径衰落条件下两种常规测向方法的误差问题

讨论了莱斯多径衰落信道模型在两类常规测向技术中的应用。利用常规测向技术对信噪比的特定要求,分析了具有莱斯分布特性衰落信道对比相、比幅测向误差抖动的影响,给出了其分布函数,并通过仿真指出其应用限制。最后就工程应用中所关心的模型参数获取和采样点数确定等问题作一论述。     

Investigation of corona initiation voltage at reduced pressures

The results of an experimental study of the 60 Hz ac corona inception voltage at reduced pressures for a cylindrical conductor and a parallel ground plane are presented. Several spacings and bare and insulated conductors of several diameters are considered. Empirical expressions from which a reasonably accurate prediction of the corona inception voltage (CIV) may be made have been inferred from experimental data     

A recursive multiple model approach to noise identification

Correct knowledge of noise statistics is essential for an estimator or controller to have reliable performance. In practice, however, the noise statistics are unknown or not known perfectly and thus need to be identified. Previous work on noise identification is limited to stationary noise and noise with slowly varying statistics only. An approach is presented here that is valid for nonstationary noise with rapidly or slowly varying statistics as well as stationary noise. This approach is based on the estimation with multiple hybrid system models. As one of the most cost-effective estimation schemes for hybrid system, the interacting multiple model (IMM) algorithm is used in this approach. The IMM algorithm has two desirable properties: it is recursive and has fixed computational requirements per cycle. The proposed approach is evaluated via a number of representative examples by both Monte Carlo simulations and a nonsimulation technique of performance prediction developed by the authors recently. The application of the proposed approach to failure detection is also illustrated     

一种新颖的瞬时浮点放大器

介绍了瞬时浮点放大器的原理及构成，并给出一种结构新的具有２５６阶的瞬时浮点放大器，可有效地提高数据采集系统的测量范围。     

六喷管超音速引射器性能的理论分析和实验研究

对某一定尺寸的六喷管超音速引射器进行气动性能的实验研究。结果表明：随着主次流压比Ｐ＊ｐ／Ｐ＊ｓ增加，引射系数及修正引射系数下降；当引射系数增加时，混合管动量修正系数Ｋｍ下降，但主喷管流量系数μ变化不大。对上述工况进行理论计算的结果与实验数据符合良好。     

Tracking in clutter with nearest neighbor filters: analysis andperformance

The measurement that is “closest” to the predicted target measurement is known as the “nearest neighbor” (NN) measurement in tracking. A common method currently in wide use for tracking in clutter is the so-called NN filter, which uses only the NN measurement as if it were the true one. The purpose of this work is two fold. First, the following theoretical results are derived: the a priori probabilities of all three data association events (updates with correct measurement, with incorrect measurement, and no update), the probability density functions (pdfs) of the NN measurement conditioned on the association events, and the one-step-ahead prediction of the matrix mean square error (MSE) conditioned on the association events. Secondly, a technique for prediction without recourse to expensive Monte Carlo simulations of the performance of tracking in clutter with the NN filter is presented. It can quantify the dynamic process of tracking divergence as well as the steady-state performance. The technique is a new development along the line of the recently developed general approach to the performance prediction of algorithm with both continuous and discrete uncertainties     

基于Riccati方程的离散容错控制系统设计

基于离散系统的Ｒｉｃｃａｔｉ方程，提出一种对传感器失效具有完整性的离散控制系统的设计方法，给出了完整性设计方法的设计步骤，并用设计实例验证了该方法的有效性．该方法还可推广用于执行器失效的情况．     

流变铸造法制备Al_2O_（3P）／ZA4－3复合材料的研究

为提高模用锌合金ＺＡ４－３的性能，扩大其应用范围，本项工作采用流变铸造法成功地制备了性能稳定的Ａｌ２Ｏ３Ｐ／ＺＡ４－３复合材料。对该材料进行了弯曲强度、冲击韧性、压缩强度、硬度及耐磨性等性能试验，结果表明：Ａｌ２Ｏ３ｐ的加入，使锌合金的压缩强度、室温和高温硬度以及耐磨性明显提高，其弯曲强度略有降低，而其冲击韧性下降了　。最后还讨论了成形工艺参数、颗粒含量和颗粒直径对该复合材料性能的影响。     

某型飞机机翼Ⅱ梁框检修周期的计算

本文建立某型飞机Ⅱ梁框结构裂纹形成寿命NP 与裂纹扩展寿命N P 之间的可靠度模型 ,将安全寿命设计与损伤容限设计原理有机结合 ,计算了在给定结构可靠度下该型飞机机翼Ⅱ梁框的检修周期