航天器的有限时间时变滑模姿态控制方法设计

本文研究具有参数不确定性和外部扰动的航天器姿态控制问题.针对修正罗德里格参数表征的航天器姿态模型提出一种有限时间时变滑模函数,在此基础上设计一种有限时间收敛的滑模姿态控制方法,并证明其稳定性,给出控制参数的设计方法.该方法在保证系统渐近稳定的前提下,不仅能够实现姿态跟踪误差在有限时间内收敛,而且能够实现姿态跟踪误差在设定的时间收敛,且全局具有滑模动态确定的系统响应.通过仿真结果验证本文提出方法的有效性.     

反导多传感器协同任务规划综述

针对反导作战多传感器协同任务规划的相关问题,结合反导作战的特点,探讨反导作战信息处理过程与多传感器协同任务规划的关系,并分析多传感器协同任务规划的内涵;在此基础上,梳理出多传感器协同任务规划涉及的关键技术,并综述多源信息综合处理、多传感器协同部署、协同跟踪、协同引导和协同识别等关键技术的研究现状;最后就多传感器协同任务规划的发展提出一些建议。     

高超声速飞行器舱内压力预测

针对高超声速飞行器独特的飞行状态及环境特点,对其舱体内部压力变化进行了预测研究。综述飞行器的被动式及主动式舱内压力控制系统特点,提出采用准一维等熵流公式结合计算流体动力学(CFD)进行舱内压力预测的方法,研究被动式充排气系统对舱内压力变化的影响,为高超声速飞行器充排气系统的设计提供了重要的参考和依据。     

受轮缘密封结构影响的1.5级涡轮封严流与主流的相互作用以及轮缘密封间流动干扰

为探究动叶上游不同轮缘密封结构封严出流对1.5级涡轮端区流场及轮缘密封间流动干扰的影响区别,通过Shear Stress Transport （SST）湍流模型对无密封腔室,上游密封结构分别为简单斜向、简单径向,下游密封腔室为简单轴向的1.5级涡轮进行了非定常数值模拟。结果表明：轮缘密封间干扰使带径向密封结构模型的下游轮缘腔室内封严效率偏低,并增强了固有的非定常不稳定特性。上游密封结构变化对动叶和第2级静叶流动的影响差异分别位于35%、65%叶高范围内;径向密封结构增加了上游静叶的堵塞效应、动叶入口气流的欠偏转程度、叶根吸力面负荷与14%叶高以上的轮毂通道涡强度,并在第2级静叶入口处产生更多低频压力波动,使其尾缘脱落涡尺度增大但13%叶高以上的轮毂通道涡强度较弱。与无密封腔室相比,通入封严气体总量为主流流量的0.8%时,带斜向密封结构的1.5级涡轮气动效率降低了0.94%,且带径向密封结构的1.5级涡轮气动损失额外增加了0.17%。     

分腔流量比对涡轮曲端壁表面冷却特性实验

利用高速风洞及压敏漆（PSP）技术,研究了端壁表面不同分腔流量比对端壁表面的气膜冷却效率的影响。对比各个分腔在不同流量比下端壁表面的气膜冷却效率的详细分布发现：端壁表面的气膜冷却效率随着槽缝流（分腔1）流量比的增加而增大,随着槽缝喷射冷气流量的增加,冷气在端壁表面的覆盖范围变广,同时冷却效果也有所提升;随着端壁前部分腔（分腔2）冷气流量比的增加,叶栅通道喉部上游区域的冷却流体会出现明显的吹离壁面的情况,端壁表面的气膜冷却效率也会随之减小;端壁后部分腔（分腔3）冷气流量比对端壁表面的冷却效率的影响与分腔2类似。     

Direct trajectory optimization based on a mapped Chebyshev pseudospectral method

 In view of generating optimal trajectories of Bolza problems, standard Chebyshev pseudospectral (PS) method makes the points' accumulation near the extremities and rarefaction of nodes close to the center of interval, which causes an ill-condition of differentiation matrix and an oscillation of the optimal solution. For improvement upon the difficulties, a mapped Chebyshev pseudospectral method is proposed. A conformal map is applied to Chebyshev points to move the points closer to equidistant nodes. Condition number and spectral radius of differentiation matrices from both methods are presented to show the improvement. Furthermore, the modification keeps the Chebyshev pseudospectral method's advantage, the spectral convergence rate. Based on three numerical examples, a comparison of the execution time, convergence and accuracy is presented among the standard Chebyshev pseudospectral method, other collocation methods and the proposed one. In one example, the error of results from mapped Chebyshev pseudospectral method is reduced to 5% of that from standard Chebyshev pseudospectral method.     

苏通大桥实测强风湍流积分尺度的对比研究

湍流积分尺度是体现风特性的重要指标之一,而现场实测是获得工程结构准确可靠的风特性的唯一有效手段.本文利用苏通大桥结构健康监测系统(SHMS)采集的风特性数据库,选取该桥址区2008年夏季的“凤凰”、“海鸥”台风及冬季北风为样本进行强风特性分析.其中采用4种常用计算方法重点研究了桥址区强风的积分尺度,并对比了不同方法的计算结果以验证其可靠性.最后分析了湍流积分尺度随高度和平均风速等的变化规律.结果表明:湍流积分尺度与风速之间无确定关系,塔顶湍流积分尺度较跨中大.分析结果充实了苏通大桥风特性数据库,可为湍流积分尺度的分析计算提供参考,并为苏通大桥的强风环境和抗风评估提供了实测依据.     

Form-finding methods for deployable mesh reflector antennas

Deployable high-frequency mesh reflector antennas for future communications and obser- vations are required to obtain high gain and high directivity. In order to support these new missions, reflectors with high surface accuracy are widely required. The form-finding analysis of deployable mesh reflector antennas becomes more vital which aims to determine the initial surface profile formed by the equilibrium prestress distribution in cables to satisfy the surface accuracy requirement. In this paper, two form-finding methods for mesh reflector antennas, both of which include two steps, are pro- posed. The first step is to investigate the prestress design only for the cable net structure as the circum- ferential nodes connected to the supporting truss are assumed fixed. The second step is to optimize the prestress distribution of the boundary cables connected directly to the supporting truss considering the elastic deformation of the antenna structure. Some numerical examples are carried out and the simulation results demonstrate the proposed form-finding methods can warrant the deformed antenna reflector surface matches the one by design and the cable tension forces fall in a specified range.     

Passive inter-modulation scattering analysis of reflector considering contact nonlinearity

 Passive inter-modulation (PIM) is a form of nonlinear distortion caused by the inherent nonlinearities of the passive devices and components in RF/microwave system. It will degenerate the performance of communication system with broad-band channel and high-sensitivity receiver. Therefore, it is necessary to construct a model to simulate this process in order to predict the level of PIM. This paper is aimed at constructing some plate models with one-dimensional and two-dimensional contact nonlinearity sections illuminated by two-tone waves, and calculating the scattered field at a fixed-point in space using time-domain physical optics method. By taking fast Fourier transform (FFT), we get the spectrum of the scattered field and then analyze the generated PIM products. At the end of this paper, some numerical examples are presented to show the influence rules of the relative factors on PIM. The results indicate the variation of the level of PIM with the number of the nonlinear regions, the nonlinear spacing, and the incident power levels.     

Trajectory control strategy of cathodes in blisk electrochemical machining

A turbine blisk, which combines blades and a disk together, is one of the most important components of an aero engine. In the process of blisk electrochemical machining (ECM), the sheet cathode, which is usually used as a tool electrode, has a complicated structure. In addition to that, the channel between the adjacent blades is narrow and twisted, so interference is apt to happen when the sheet cathode feeds into the channel. Therefore, it is important to choose suitable trajectory control strategy. In this paper, a new trajectory control strategy of the sheet cathode is presented and corresponding simulation analysis is conducted on the basis of an actual blisk model. The simulation results demonstrate that the sheet cathode can feed into the channel by a spatial line trajectory without interference. Moreover, the verification experiments are carried out according to the simulation. The experimental results show that the cathode can move into the channel without interference. It is verified that the new trajectory control strategy is correct and can be used in the blisk ECM process successfully.