Effect of nickel introduced by electroplating on pyrocarbon deposition of carbon-fiber preforms

In order to improve the deposition rate and microstructure of pyrocarbon, nickel was introduced by electroplating on carbon fibers and used as a catalyst during the deposition of pyrocarbon at 1000 C using methane as a precursor gas. The distribution of nickel catalyst and the microstructure of pyrocarbon were characterized by scanning electron microscopy（SEM）, energy dispersive spectroscopy（EDS）, X-ray diffraction（XRD）, and Raman micro-spectrometry. Results show that nano-sized nickel particles could be well distributed on carbon fibers and the pyrocarbon deposited catalytically had a smaller d002 value and a higher graphitization degree compared with that without catalyst. In addition, the deposition rate of pyrocarbon in each hour was measured.The deposition rate of pyrocarbon in the first hour was more than 10 times when carbon cloth substrates were doped with nickel catalysts as compared to the pure carbon cloths. The pyrocarbon gained by rapid deposition may include two parts, which are generation directly on the nickel catalyst and formation with the carbon nanofibers as crystal nucleus.     

焊缝补强方式对大直径贮箱箱底承载性能影响

基于有限元法研究了典型10 m级直径贮箱箱底焊缝在双面对称补强、内表面补强及外表面补强三种情况下的内压承载性能。数值计算采用二维对称平面模型,考虑了筒段和短壳真实边界条件及焊缝对承载能力的影响,构建的考虑材料塑性的非线性数值分析模型准确地获得了贮箱箱底内外表面经向应力。结果表明:顶盖和瓜瓣焊缝区域是箱底的薄弱位置,使用内压下,双面对称补强的加强区内外表面经向应力差较小,结构均未进入塑性,单面补强的加强区内外表面经向应力差远大于双面对称补强,局部进入塑性,且外表面补强的加强区最大和最小经向应力差相对于内表面补强分别增加了9.7%和27.2%,变形不协调；设计内压下,箱底内外表面均有局部进入塑性,材料塑性对内外表面经向应力差有一定的缓解作用,能够显著缓解内外表面应力差造成的附加弯矩；双面对称补强优于内表面补强,内表面补强优于外表面补强,单面补强易产生附加弯矩,不利于箱底的均匀承载和变形协调。该研究结果指导了大直径贮箱箱底结构的优化设计。     

Control of a Spherical Robot: Path Following Based on Nonholonomic Kinematics and Dynamics

This paper presents the controller design for the path following of a spherical mobile robot,BHQ-1.Firstly,a desired velocity for the reference path is deduced from the kinematic model,which cannot be transformed into the classic chained form.Secondly,a necessary torque for the desired velocity is obtained based on the dynamic model.As to the kinematics,a one-dimensional function is selected to measure the two-directional tracking error,and the velocity of rolling forward is reasonably assumed to be constant;therefore the multiple-input multiple-output (MIMO) system is transformed into a single-input single-output (SISO) system.As to the dynamics,both exact dynamics and inexact dynamics with modeling error as well as bounded unknown disturbance are taken into account,based on which a proportional-derivative (PD) controller and a sliding mode controller with adaptive parameters are proposed respectively.Finally,convergence analysis and simulation results are provided to validate these controllers.     

学生成绩管理及学费管理信息系统的软件开发

本文详细介绍了沈阳航空工业学院学生成绩管理及学费管理信息系统的功能及实现技术。此系统基于校园网环境，实现了教务管理中的成绩管理、学费管理及有关的各项统计。     

论我国高师矩阵结构课程体系的有效性

本从结构、课程设置和课程内容等方面分析了我国高师现行课程体系存在的缺陷，进而提出横向模块、纵向两系列的高师矩阵结构课程体系的基本思路和组成框架。重点从理论上实践上的合理性和统一性等方面分析了矩阵结构课程体系的有效性。     

一个超冗余度移动操作臂机器人系统的实现与运动控制

冗余度或超冗余度移动操作臂机器人可在空间站上为宇航员提供很大的帮助.对一个超冗余度移动操作臂机器人系统的设计和实现作了介绍,这个系统由一个8自由度的模块机器人和一个1自由度的电机驱动的导轨组成;对该系统的逆运动学解法进行了讨论,提出了一种基于避关节极限与位形优化的简化逆运动学控制方法;并提供了仿真和实验结果.     

吸波涂层用酚氧树脂粘结剂研究

选用酚氧树脂作为吸波涂层（ＲＡＣ）粘结剂，研究了溶剂、分子量、固化剂对ＲＡＣ主要力学与物化性能的影响。结果表明、酚氧树脂ＲＡＣ可室温固化，附着力、柔韧性和耐冲击性能可满足飞行器的使用要求。     

直升机驾驶舱人机功效设计

直升机驾驶舱人机功效的设计主要是指有人驾驶的直升机。人机功效的设计成功与否直接影响到直升机的使用效能、驾乘安全性、可操纵性和可维修性。人机功效涉及面很广,在设计应用上它对整机及各个系统都有相关的技术要求,因此人机功效设计是一个多学科、集成的综合应用技术。本文重点就直升机驾驶舱的人机功效设计做如下探讨。     

薄翼型阵风响应的数值模拟

 采用有限体积法来数值求解非定常Euler和N-S方程，并在非定常计算中通过引入“网格速度”来计入阵风的影响，实现了对刚性薄翼型阵风响应的有效数值模拟。采用该方法来对薄翼型迎角突然增大的阵风、陡边型阵风这两种典型阵风情况下的翼型气动力响应进行了计算，结果表明：计算结果与现有的一些理论结果都符合较好，与文献中计算结果也吻合。同时通过计算也表明厚翼型的阵风响应需根据工况开展进一步的计算分析。