卫星通信干扰样式研究

综述通信对抗干扰的分类方式,分析了部分文献中对干扰样式划分的不合理性.根据卫星通信对抗的特点将通信对抗干扰样式进行分类,并从与压制式干扰相区别的角度对欺骗式干扰做出研究分析.     

高速BPSK相干光通信系统对激光器线宽要求

文章概述了激光器相位噪声对零差相干检测光通信系统性能的影响，对特定的基于平衡探测的科斯塔斯（Costas）环路接收系统相位误差进行了详细的理论分析，最后获得了不同传输码速率下的零差相干检测光通信系统对激光器线宽的具体要求。     

电大目标等离子体隐身的矩量法优化设计

根据高频散射特征,提出典型几何散射中心替代法,用于解决矩量法（MOM）用于电大目标等离子体隐身时的优化设计问题。以某典型电大目标为例,通过仿真分析了该方法的可行性。结果显示,电大目标覆盖利用该方法得到最优参数的等离子体后,不仅目标整体的单站RCS平均缩减与典型几何散射体的单站RCS缩减相当,且任意方向上RCS基本都有10dB左右的缩减,表明用该方法得到用于电大目标隐身的等离子体参数是可行的。     

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

关于进行程序管制一体化模拟练习的设想

在程序管制模拟练习中，存在着塔台管制服务、进近管制服务和区域管制服务互不衔接，不能系统地模拟整个管制过程的问题。针对这一情况提出了程序管制一体化模拟练习和程序和管制一体化模拟机的结构设计。     

Characteristics of low-latitude whistlers and their relation with f0F2 and magnetic activity

Some results obtained from the characteristics of low-latitude whistlers received at Wuchang (Geomag. Lat. 19.2°N), Zhanjiang (9.8°N) and Yulin (6.4°N) are presented. The observations cover three years at Wuchang, two years at Zhanjiang, one year at Yulin.     

航空中的力反馈技术

对力反馈在航空中的应用进行综述,主要涉及无人机遥操作和飞行安全性两大领域。首先,为了解决无人机所捕获的图像信息在分辨率、动态范围、视野等方面的不足,力反馈技术逐渐被引入,并得到了初步应用。起初没有考虑地面控制站与无人机之间的通讯时延问题,力反馈与小波变量的结合能有效地解决时延问题,但操纵负荷仍然很大,继而力刚度反馈技术被提出。其次,飞机执行器速率的限制易导致飞行员诱发的震荡危及飞行安全,为了有效地抑制这类震荡,智能提示和智能增益技术被提出。通过上述的分析和探讨,说明力反馈技术在航空中的研究与应用具有重要的意义。     

光学基片表面软质抛光胶体粒子的激光清洗

介绍了光学基片表面软质抛光胶体粒子激光清洗的基本方法、原理和实验装置,并通过对含有污染微粒的基片表面进行激光清洗,获得了高洁净表面的光学基片.     

On the electrodynamics of counter stream in pulsar’s inner annular cap region

The electric properties of pulsar’s inner annular gap are explored in this paper. Under two main assumptions, (1) the pulsar is alive, (2) the total charge of pulsar should not vary with time, the condition for the acceleration of negative particle in the annular region is derived. The acceleration condition is j₋ ? 0.5j₊, i.e., the current carried by negative particles is greater than or equal to 0.5 times of the current carried by positive particles. This condition holds even when the backward flow of positive particles exists in the annular region. It is noted that the outflow of negative particles offers good opportunities to understand the current closure problem of pulsar as well as wide radiation beam of pulsar observed at high energy band.     

考虑前屈曲几何非线性影响的结构稳定性分析

本文采用有限元法分析考虑前屈曲几何非线性影响的结构稳定性。应用伴有线性搜索和各种牛顿型解法的组合弧长法可以顺利地描述包含有极值点的载荷一位移曲线,与此同时,若在加载点处计算结构刚度矩阵的行列式值、临界载荷因子和特性刚度参数等值,则可根据稳定准则,通过插值确定临界点的位置。从而为研究复杂结构稳定性提供简便而有效的方法。