基于回归型支持向量机的空战目标威胁评估

空战目标威胁评估是协同多目标攻击中的关键问题.针对传统空战目标威胁评估方法在确定权重系数方面的不足,提出了一种新的基于回归型支持向量机的评估方法.在分析了现有的空战目标威胁评估方法中距离威胁模型存在缺陷的基础上,提出了改进的距离威胁模型.建立了基于回归型支持向量机的空战目标威胁评估模型,利用该模型对想定的空战目标进行了威胁评估.仿真结果表明,该方法具有很好的预测能力,可以快速、准确地完成空战目标威胁评估.     

基于退步控制方法的绳系卫星回收张力控制

利用退步控制方法研究了绳系卫星系统TSS(Tethered Satellite System)的平面内回收控制问题,提出了一种新的张力控制律.该控制律设计由两步组成:首先利用退步控制将摆角稳定到目标值,然后通过设计摆角的目标值实现系绳的回收和回收速度的控制.控制率设计了分段连续的目标角度方案和延时环节,可以使TSS回收过程各状态量变化平滑.数值仿真结果表明,该控制律在圆轨道、近圆轨道和大偏心率的椭圆轨道都有很好的控制效果.     

水泵叶轮的流动叠加设计方法与CFD仿真

叶轮叶片是复杂的空间曲面体,它直接影响到水泵的水力性能及运行稳定性.发动机水泵叶轮流动叠加设计是通过分析流体的流动规律,按其流动轨迹进行叶轮设计,将流体在离心水泵内的流动看作叶轮静止时的轴向和径向流动和叶轮旋转时的周向流动的叠加,从而用绕角流动和源环流的流体流动规律设计出叶轮的轴面轮廓和叶片骨线.通过CFD(Computational Fluid Dynamics)仿真,可以证明该方法从结构上避免了流体流动过程中由于空间的相对不均而造成的压力不均,减轻了回流、二次流,相应地减少能量的损失,提高水泵的效率.     

基于MLPG混合配点法的接触问题形状优化

分别介绍了接触问题和MLPG(Meshless Local Petrov-Galerkin)混合配点法的理论基础,推导了相关公式,给出了两种典型接触状态的定解条件,使用二维线性基函数,采用三次样条曲线权函数,通过移动最小二乘法插值,将MLPG混合配点法运用到接触分析中,使用罚函数法添加本质边界条件,对二维弹性接触问题的接触过程进行模拟,反复迭代得到真实的接触情况,建立了一种新的应力-位移非线性数学求解模型,结合遗传算法对实际工程接触问题进行了求解优化,给出优化结果和目标函数变化曲线,并与相关文献结果比较,验证了该方法的有效性.     

基于等效梁模型的长直机翼动力学与颤振分析

针对多自由度的复杂结构,建立简化的等效结构模型,可以快速、有效地进行结构分析.采用能量等效的方法,将多自由度、结构复杂的长直结构等效为空间梁,推导得出等效梁的刚度值和惯量值,利用有限元法得到总体刚度阵和质量阵.针对某机翼模型,得出了等效梁的刚度值和惯量值,进行了振动和颤振特性分析,并分别与有限元软件的计算结果作了对比.结果表明:该等效建模法大大降低了结构自由度,振动及颤振分析误差较小,而且其主要参数值方便修改,因此该方法可用于飞行器的初级设计或结构优化设计.     

纳米TiC粉末改性钎料钎焊CBN磨粒的结合界面和磨损特性

采用了Ag-Cu-Ti 合金和纳米 TiC 粉末组成的新型复合钎料钎焊立方氮化硼(CBN)磨粒和工具基体,运用了三维体式显微镜和扫描电镜,研究了CBN磨粒与改性钎料之间的结合体系,包括界面微结构和反应产物,并进行了钎焊磨粒耐磨性试验.试验结果表明:加入的纳米TiC粉末均匀分布在钎料层内,细化了Ag-Cu-Ti合金钎料层的显微组织,有效控制了CBN磨粒与钎料的剧烈反应;磨粒表面化合物均匀致密,确保了CBN磨粒、纳米改性钎料和基体之间的结合强度;钎焊CBN磨粒的磨损形式以磨耗磨损为主,后期出现微小破碎,无磨粒脱落.     

Monocular Vision-based Two-stage Iterative Algorithm for Relative Position and Attitude Estimation of Docking Spacecraft

Visual sensors are used to measure the relative state of the chaser spacecraft to the target spacecraft during close range rendezvous phases. This article proposes a two-stage iterative algorithm based on an inverse projection ray approach to address the relative position and attitude estimation by using feature points and monocular vision. It consists of two stages: absolute orientation and depth recovery. In the first stage, Umeyama's algorithm is used to fit the three-dimensional (3D) model set and estimate the 3D point set while in the second stage, the depths of the observed feature points are estimated. This procedure is repeated until the result converges. Moreover, the effectiveness and convergence of the proposed algorithm are verified through theoretical analysis and mathematical simulation.     

Multi-frequency RCS Reduction Characteristics of Shape Stealth with MLFMA with Improved MMN

Three new control factors are presented for calculating the multipole mode number (MMN) efficiently and precisely. The effects of these control factors on the number of integral samples and the precision of multilevel fast multipole algorithm (MLFMA) are investigated. A new approach based on control factors which is proven to be able to improve the computational efficiency and reduce the needed memory significantly as well as ensuring the proper precision. For three aircraft models, the improved MLFMA is employed to analyze their multi-frequency scattering characteristics. It is found that aircraft shape can influence radar cross section (RCS) in different frequency zones. Both the multi-frequency RCS reduction characteristics of shape stealth aircraft and the conventional aircraft with stealth design taken into account are investigated, and the results show that shape stealth exhibits significant RCS reduction in the resonance and high-frequency zones, and with a weaker influence in the Rayleigh zone. Compared with radar absorbing material (RAM), shape stealth yields a wider multi-frequency RCS reduction. The above-mentioned results can be applied to stealth design for multiple frequencies or even for all frequencies.     

低速风洞绳牵引并联支撑系统的模型气动试验研究(英文)

根据绳牵引并联机构的优点,建造了一种新型的用于低速风洞试验的飞机模型绳牵引并联支撑系统,研究该系统中模型的空气动力参数的测量与计算方法。文中对机构进行了静力学分析,建立了描述实验模型气动载荷的数学模型,提出了通过测量绳系拉力求得模型空气动力参数的解算方法;设计并构建了绳系拉力测量及数据采集系统;将该系统置于开口式回流低速风洞中进行了吹风试验,采集了模型在不同姿态和不同风速下的各牵引绳的拉力数据,并对数据进行了处理分析,通过解算得到了不同吹风条件下模型的气动载荷参数曲线。研究结果表明,绳牵引并联机构用于低速风洞试验的支撑系统是可行的。     

Design and Optimization of 3D Radial Slot Grain Configuration

Upper stage solid rocket motors (SRMS) for launch vehicles require a highly efficient propulsion system. Grain design proves to be vital in terms of minimizing inert mass by adopting a high volumetric efficiency with minimum possible sliver. In this article, a methodology has been presented for designing three-dimensional (3D) grain configuration of radial slot for upper stage solid rocket motors. The design process involves parametric modeling of the geometry in computer aided design (CAD) software through...