基于图像分析的雷达假目标逼真度计算

在对目标雷达图像进行分析的基础上,提取其图像特征,并通过一定的变换使其转化为假目标的逼真度指标,从而对雷达假目标的设计提供参考.     

Gust load alleviation wind tunnel tests of a large-aspect-ratio flexible wing with piezoelectric control

An active control technique utilizing piezoelectric actuators to alleviate gust-response loads of a large-aspect-ratio flexible wing is investigated. Piezoelectric materials have been exten-sively used for active vibration control of engineering structures. In this paper, piezoelectric mate-rials further attempt to suppress the vibration of the aeroelastic wing caused by gust. The motion equation of the flexible wing with piezoelectric patches is obtained by Hamilton's principle with the modal approach, and then numerical gust responses are analyzed, based on which a gust load alle-viation (GLA) control system is proposed. The gust load alleviation system employs classic propor tional-integral-derivative (PID) controllers which treat piezoelectric patches as control actuators and acceleration as the feedback signal. By a numerical method, the control mechanism that piezo-electric actuators can be used to alleviate gust-response loads is also analyzed qualitatively. Further-more, through low-speed wind tunnel tests, the effectiveness of the gust load alleviation active control technology is validated. The test results agree well with the numerical results. Test results show that at a certain frequency range, the control scheme can effectively alleviate the z and x wing-tip accelerations and the root bending moment of the wing to a certain extent. The control system gives satisfying gust load alleviation efficacy with the reduction rate being generally over 20%.     

逆向工程中一种新的特征识别算法

从某种角度上说,逆向工程是从已有实物的测量数据点中提取其实体特征再进行模型重建的过程。本文提出了一种新的特征识别算法,其首先采用基于面积和法矢准则的数据分割技术,对测量数据点进行数据分割。然后从特征所包含的分割面(简称特征分割面)中提取能够惟一标识该特征的4种特征编码,分别为:表述特征截面形状的截面编码、描述特征凹凸性的凹凸编码、显示特征二维俯视轮廓形状的轮廓编码以及反映特征二维俯视轮廓是否封闭的开闭编码。最后将这4种编码输入到基于人工神经(BP)网络的自动特征识别系统中,识别出特征类型并提取特征参数,从而实现特征重建。着重研究并实现了从特征分割面中提取特征编码的算法,并验证了算法的有效性。     

基于N-S方程的加油机对受油机气动干扰研究

空中加受油时,加油机尾流场会对受油机产生复杂的流动干扰。采用基于Navier-Stokes(N-S)方程的CFD方法分析加油机尾流场,并对加油机、受油机之间的气动干扰进行一体化模拟研究;系统地分析加油机不同迎角及双机不同高度差、不同侧向距离、不同前后位置时,受油机的纵向、横航向气动力特性。结果表明：典型状态下,加油机迎角增大,对受油机的气动干扰增强;高度差越大,对受油机气动干扰越小;侧向距离越大,对受油机气动干扰先增加后减小;前后距离对受油机的影响较小。     

功能分析与失效物理结合的可靠性预计方法

 可靠性预计是产品设计、研发过程中的重要工作,全面准确的可靠性预计可以评价产品的可靠性水平,也可以为设计提供信息,指导设计。全面分析总结当前电子设备可靠性预计相关技术方法,以当前基于失效物理(POF)技术的系统可靠性预计方法中,并未考虑产品功能组成关系的缺陷为突破点,建立了一种以失效物理分析为基础,综合考虑电路功能组成关系的电子设备可靠性预计方法。该方法从电路功能出发,通过灵敏度仿真和主成分分析两种方法,确定对电路性能起主要影响的关键单元,再通过失效物理分析或统计规律明确单元的失效概率分布,通过混合分布获得系统的分布,得到系统可靠性指标。最后以某航空机电产品的电源电路为案例,对本预计方法进行验证。     

Compensation of base disturbance using optimal trajectory planning of dual-manipulators in a space robot

This paper presents a trajectory planning algorithm for a space robot with dual-manipulators. Here one manipulator of the space robot captures a target, and another manipulator is free. In this case, this study uses one manipulator as the mission manipulator to capture the target, and another as the balance manipulator aiming at the compensation of the pose disturbance. For this method, a novel trajectory planning algorithm applied to the balance manipulator is presented. The trajectory planning problem is transformed into series of problems of the optimal state solution, and then the iterative algorithms for the trajectory planning are designed. In the iterative algorithms, the bias force on the spacecraft base caused by the balance manipulator is used as the compensation force. Then, to calculate the expected compensation force and torque, a pose control law for the spacecraft base is introduced. The expected compensation force and torque provide equality constraints for optimization problems, which implies that the trajectory planning algorithm compensates for not only the disturbance generated by the manipulator’s motion, but also environmental disturbances. This is because the expected compensation force and torque depend on the pose change of the spacecraft base rather than the type of the disturbance. Numerical simulation was carried out to analyze the proposed trajectory planning method. It was observed that the method greatly reduces the disturbance of Manipulator A on the spacecraft base. These results validated the effectiveness of the proposed method for the trajectory planning to make the spacecraft base disturbance up to minimum.     

地基光学图像中本体-帆板结构航天器姿态估计方法

提出一种利用地基光学图像估计空间目标姿态的方法。针对本体-帆板结构航天器外形结构特点，定义了一种不易遮挡的两轴结构特征，设计了地基光学图像中该特征的提取方法；根据航天器成像过程建立了特征点二三维几何投影方程，实现了航天器三维姿态的解算。利用单站序列图像，可获得航天器姿态变化角速度信息。在轨航天器的试验结果表明，本方法能有效地从地基光学图像估计出航天器姿态。     

宽频带中频相位计的研制

比较全面地介绍了-宽带中频相位计的研制过程。论述了相位计的工作原理,给出了系统框图。对各个部件的设计做了介绍,并给出了相位计所达到的技术指标。还介绍了系统测试方法和检定方法,对系统的误差做了分析,并给出了理论计算误差与实测误差的对应关系,提出了今后的进一步设想。     

CFD predictions of LBO limits for aero-engine combustors using fuel iterative approximation

Lean blow-out (LBO) is critical to operational performance of combustion systems in propulsion and power generation. Current predictive tools for LBO limits are based on decadesold empirical correlations that have limited applicability for modern combustor designs. According to the Lefebvre’s model for LBO and classical perfect stirred reactor (PSR) concept, a load parameter (LP) is proposed for LBO analysis of aero-engine combustors in this paper. The parameters contained in load parameter are all estimated from the non-reacting flow field of a combustor that is obtained by numerical simulation. Additionally, based on the load parameter, a method of fuel iterative approximation (FIA) is proposed to predict the LBO limit of the combustor. Compared with experimental data for 19 combustors, it is found that load parameter can represent the actual combustion load of the combustor near LBO and have good relativity with LBO fuel/air ratio (FAR). The LBO FAR obtained by FIA shows good agreement with experimental data, the maximum prediction uncertainty of FIA is about ±17.5%. Because only the non-reacting flow is simulated, the time cost of the LBO limit prediction using FIA is relatively low (about 6 h for one combustor with computer equipment of CPU 2.66 GHz · 4 and 4 GB memory), showing that FIA is reliable and efficient to be used for practical applications.     

基于高度控制的拖靶定高飞行分析

超低空飞行的航空拖靶需要高精度的高度控制,而作为试验和训练的消耗性装备,其低成本设计要求使得航空拖靶不能采用常规飞行器的高度控制方法。针对以拖曳力为飞行动力的航空拖靶,研究其基于非姿态控制的定高飞行的运动特性。定高飞行航空拖靶采用高稳定性的气动布局,并基于准直接力控制的升降舵面进行高度调整操纵。通过建立拖靶的纵向运动数学模型,设计非姿态控制定高飞行控制方法,详细分析拖靶气动特性,并进行定高飞行控制的仿真计算。计算结果给出拖靶的高度控制能力及飞行状态,结果表明拖靶具有一定的高度调整能力,可以实现定高飞行。