高效隔热材料结构与性能研究

以陶瓷隔热瓦和纳米隔热材料为研究对象,揭示了高效隔热材料结构与性能的关系.研究结果表明:随着密度的增加,隔热材料室温热导率和力学性能随之增加;陶瓷隔热瓦平面方向和厚度方向的结构和性能存在明显差异;复合纳米结构后,材料的隔热性能明显提高;室温热导率从43 mW/(m·K)降低至36 mW/(m·K);添加少量功能添加物后,材料的高温隔热性能进一步提高,高温考核中背面温度从668℃降低到576℃.同时介电常数从2.2％增加到6.6％;通过气相超临界工艺在材料表面接枝有机基团,材料表面疏水状态发生显著变化,材料具备了防水和低吸潮的特性.     

TC11 粉末钛合金的微观组织及其形成机理

通过旋转电极制粉及后续的热等静压工艺制备了全致密的TC11粉末钛合金,分析了材料的微观组织,通过理论分析和有限元模拟的方式探讨了材料独特的微观组织的形成机理.分析结果表明:粉末冶金TC11的微观组织主要由条片α+相间β相组成,同时还有部分细小的等轴α分布在粉末颗粒界面处.这种独特的微观组织是由两种工艺共同作用产生的.     

Investigation of longitudinal aerodynamic parameters identification method for fly-by-wire passenger airliners

The flight control system of a fly-by-wire （FBW） passenger airliner with a complex frame-work and high feedback gain augmentation would change the original characteristic of a loaded signal and suppress the excitation of an airplane＇s pertinent motion modes. Taking a research example of an FBW passenger airliner model with longitudinal relaxed-static-stability, a new method of signal type selection and signal parameter design is proposed, through analysis of signal energy distribution and plane body＇s frequency response. According to CCAR60--the Appraisal and Use Regulation of Flight Simulator Device, the simulation validation of the FBW passenger airliner＇s longitudinal aerodynamic parameters identification is put forward. The validation result indicates that the designed signal could excite the longitudinal motion mode of the FBW passenger airliner adequately and the multiparameter comparison in simulation meets the objective test request of CCAR60. Meanwhile, the relative errors of aerodynamic parameters are less than 10%.     

Form-finding methods for deployable mesh reflector antennas

Deployable high-frequency mesh reflector antennas for future communications and obser- vations are required to obtain high gain and high directivity. In order to support these new missions, reflectors with high surface accuracy are widely required. The form-finding analysis of deployable mesh reflector antennas becomes more vital which aims to determine the initial surface profile formed by the equilibrium prestress distribution in cables to satisfy the surface accuracy requirement. In this paper, two form-finding methods for mesh reflector antennas, both of which include two steps, are pro- posed. The first step is to investigate the prestress design only for the cable net structure as the circum- ferential nodes connected to the supporting truss are assumed fixed. The second step is to optimize the prestress distribution of the boundary cables connected directly to the supporting truss considering the elastic deformation of the antenna structure. Some numerical examples are carried out and the simulation results demonstrate the proposed form-finding methods can warrant the deformed antenna reflector surface matches the one by design and the cable tension forces fall in a specified range.     

某型客车噪声源的测试与研究

本文通过对某型客车的噪声测试分析，识别出该型客车的主要噪声源，为进一步采取有效的降噪措施提供了必要依据。     

飞行控制系统对驾驶员诱发振荡的影响

着重从飞行控制系统角度谈有人驾驶飞机的驾驶员诱发振荡问题,分析了系统杆力、传动比、间隙、摩擦力以及飞控伺服作动器对驾驶员诱发振荡的影响,用矢量图简明地反映飞机产生驾驶员诱发振荡的可能性和趋势。对飞机飞行控制系统的设计和对驾驶员诱发振荡现象的分析、处理有参考价值。     

角速率平台伺服机构的智能控制与容错研究

介绍了角速率平台伺服机构智能控制研制进展。用单片机控制,对角速率反馈通道实现了2次故障判别、1次系统重构。用Fuzzy控制建立了相应隶属函数,确定了故障判别阈值。实验表明系统工作稳定,故障的Fuzzy差别合理,故障通道切换平稳,重构后系统工作仍正常。     

LY12CZ 合金相电化学腐蚀行为的研究

分别研究了LY12CZ合金中的纯铝（Al）、晶间化合物θ（CuAl2）、S（Al2CuMg）和MnAl6在含Cl-离子的中性溶液中的电化学腐蚀行为。结果表明,各合金相作为独立相在含Cl-离子的中性介质中均有点蚀敏感性,其中S相耐蚀性最差,L1相耐蚀性最好。各相点蚀主要是由于Al或Mg的阳极溶解所致,腐蚀产物主要是铝的不溶性氢氧化物、可溶性氯化物及镁的可溶性盐类。     

沿曲面交线多坐标数控加工的算法研究

分析了曲面交线加工中刀具的偏置类型,提出了新的交线加工刀位轨迹生成算法。该算法利用曲面跟踪求交算法计算两曲面交线,并根据交线处曲面局部微分几何性质推算刀具的初始位置,然后采用牛顿迭代算法精确刀位。该算法的优点是能够精确控制刀具与曲面的加工误差,可处理单支点、双支点偏置情况下球头刀、平底刀、圆角刀的交线域加工,算法稳定、统一。     

利用疲劳裂纹扩展速率估算断裂韧性

提出了一种利用疲劳裂纹扩展速率来估算断裂韧性的方法,并利用2种材料12组试验数据对该法产生的误差及其控制方法进行了分析研究,结果表明,其误差可以控制在试验分散带内。