基于图像识别的发动机内窥智能检测系统研究

介绍了一种基于图像识别技术的航空发动机内窥检测的新方法，采用最大类间方差法计算二值化分割的最佳阈值，并将提取的图像特征输入神经网络进行分层识别，最后由专家系统对损伤程度进行了诊断。通过现场测试，证明了该方法的有效性和实用性．     

钛合金表面镍包石墨喷涂层的耐磨性能

为了提高钛合金的表面耐磨性,利用氧乙炔热喷涂枪,在TC4合金表面上制备出镍包石墨涂层。采用MXP-2000型销盘式摩擦磨损实验机,进行钛合金及其镍包石墨涂层的干摩擦磨损实验,并利用扫描电镜对磨损表面进行观察和分析。实验结果发现,镍包石墨涂层的摩擦系数只有钛合金的一半左右,前者磨损量为后者的1/6,说明镍包石墨涂层可以大大提高钛合金的表面耐磨性能。TC4合金的磨损机制以黏着磨损为主,喷涂层的磨损机制以磨粒磨损为主,喷涂层中的石墨润滑相是其耐磨性高的主要原因。     

空载固体发动机计算与试验模态相关性分析

为了预测空载状态固体火箭发动机动态特性,对其进行了模态试验,并应用MSC.Marc进行了模态计算,然后对比两者的结果,进行了相关性分析和评估。计算得到了发动机250Hz以内的一阶弯曲模态和五阶呼吸模态。试验测得了发动机的三阶呼吸模态和一阶弯曲模态。比较试验测试模态和与之对应的计算模态:固有频率相对误差均在5%以内;振型相关图上的点大都分布在斜率为1(或 1)的直线周围;MAC(模态置信判据)值在0 9左右。说明计算与试验模态有较好的相关性,有限元计算模型比较准确的反映了实际情况。     

An innovative study on low surface energy micronano coatings with multilevel structures for laminar flow design

Laminar flow design is one of the most effective ways to reduce the drag of a commercial aircraft by expanding the laminar flow region on the surface of the aircraft. As material science develops, the emergence of new materials such as low surface energy materials has offered new choices for laminar flow design of commercial aircraft. Different types of low surface energy micro-nano coatings are prepared to verify the effects on the boundary layer transition position and the drag of the airfoil through wind tunnel tests. The infrared thermal imaging technology is adopted for measuring the boundary layer transition, while the momentum integral approach is employed to measure the drag coefficient through a wake rake. Infrared thermal imaging results indicate that the coatings are capable of moving backward the boundary layer transition position at both a low velocity of Mach number 0.15 and a high velocity of Mach number 0.785. Results of the momentum integral approach demonstrate that the drag coefficients are reduced obviously within the cruising angle of attack range from 1° and 5° by introducing the low surface energy micro-nano coating technology.     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.     

偏心比对S形流道雷达散射特性的影响

在进/出口形状、进/出口面积、中心线变化规律、面积变化规律等设计参数不变的条件下,采用超椭圆方法设计了11种不同偏心比的S形流道。同时,借助迭代物理光学法与等效边缘电磁流绕射方法,对不同偏心比的S形流道进行了雷达散射特性的数值仿真分析。结果表明:若将不同偏心比S形流道的雷达散射截面变化曲线看作是波的传播轨迹,相对于偏心比为0的流道,偏心比改变了波的相位、振幅;偏心比越大,其相位越滞后、振幅越小。     

杨氏双缝干涉光程差近似计算的弱化条件分析

利用平面几何勾股定理,推导出杨氏双缝干涉实验光程差的准确表达式,对光程差表达式进行同解变换,反演了明纹中心坐标与光程差的函数关系,并对明纹中心坐标表达式进行了分析讨论,给出了数值解,得出了 5点结论。结论表明,杨氏双缝干涉实验光程差近似计算的条件可弱化为光程差远小于双缝间距,且利用经典近似方法计算明纹中心坐标在干涉级次较大时误差较大。     

自适应航天器态势分析系统

利用深度学习中的卷积神经网络理论,基于单目视觉系统和带有标识物的航天器影像,实现对航天器的三维姿态角、距拍摄点距离和相对拍摄中心偏移量的精准测量。利用机器学习理论实现网络自主学习样本特征,这一方式将大幅降低动态测量的误差。同时,这种测量方式也避免了人工提取特征的复杂过程,实现任意、精准、快速测量,对航天器在组装及发射过程中的姿态估计、距离测算起到关键性作用。     

潜射导弹发射原点测量方法

潜射导弹试验发射坐标系的原点一般应取在发射时刻(弹动时刻)导弹质心位置,这就需要高精度的水下定位测量系统。本文提出在不具备水下高精度测量能力的条件下,利用水上测量手段,对发射原点进行“靠近”测量并予以修正的方法。通过计算给出发射时刻导弹质心的大地坐标,应用于潜射导弹试验中。