航空发动机复杂型面罩子钣充液成形技术

利用先进的钣材冲压计算机仿真技术对零件成形中的关键问题进行了研究,并通过先进的充液成形技术进行了实际零件的成形试验,试验的结果与模拟结果基本一致。最后应用模拟得到的成形参数,利用钣充液成形工艺成形出了合格的零件。     

Low C/N_0 Carrier Tracking Loop Based on Optimal Estimation Algorithm in GPS Software Receivers

Suppressing jitter noises in a phase locked loop(PLL) is of great importance in order to keep precise and continuous track of global positioning system(GPS) signals characterized by low carrier-to-noise ratio(C/N0).This article proposes and analyzes an improved Kalman-filter-based PLL to process weak carrier signals in GPS software receivers.After reviewing the optimal-bandwidth-based traditional second-order PLL,a Kalman-filter-based estimation algorithm is implemented for the new PLL by decorrelating the model error noises and the measurement noises.Finally,the efficiency of this new Kalman-filter-based PLL is verified by experimental data.Compared to the traditional second-order PLL,this new PLL is in position to make correct estimation of the carrier phase differences and Doppler shifts with less overshoots and noise disturbances and keeps an effective check on the disturbances out of jitter noises in PLL.The results show that during processing normal signals,this improved PLL reduces the standard deviation from 0.010 69 cycle to 0.007 63 cycle,and for weak signal processing,the phase jitter range and the Doppler shifts can be controlled within ±17° and ±5Hz as against ±25° and ±15 Hz by the traditional PLL.     

基于灰色多层次评价方法的供应商评价

供应商选择是企业发展的重要决定因素之一。从企业整体发展的角度,建立了经营发展能力、合作意愿、企业形象三个方面的供应商评价指标体系,针对评价信息的灰色性,提出了供应商评价的灰色多层次评价方法,并通过一个算例说明了该方法的应用,为企业选择供应商提供了简单、易行的评价方法。     

两种静弹修正方法的对比

本文针对工程应用的实际情况,采用线化理论和非线化理论对同一模型进行了静气动弹性计算,并对不同马赫数、不同高度的刚弹性计算结果进行了对比分析。结果表明,低速时可忽略弹性变形对气动力的影响,而高速时必须考虑弹性变形对气动力的影响,在工程应用初期,可用线化理论对非线性段气动力进行静弹修正,虽然精度有所降低,但效率却大大提高,在后期可用非线化理论进行校核计算。     

Erosion of a Polyimide Material Exposed to Simulated Atomic Oxygen Environment

Oxygen plasma source generated by thermal cathode filament discharge has been used to study the erosion process of polyimide (PI) materials in atomic oxygen (AO) environment, and their mass loss, surface morphology and surface chemical compositions have been examined by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) after exposure to incremental AO flux. The data indicate that the physical adsorption of AO at the samples' surface results in the increase of oxygen concentration when polyimide is exposed to AO flux. Then selective chemical reactions of groups of polyimide materials with AO yield volatile organic compounds, sample mass loss is on linear increase and carpet-like surface morphology forms. In the initial exposure to AO, the reaction occurs mainly between AO and carbon in specific location of aromatic ring, then the reaction rate of C=O groups gradually increases. After AO exposure, the oxygen concentration increases while nitrogen and carbon concentration decreases. Reaction rate of groups containing nitrogen is slower compared with carbon and oxygen.     

钻孔法测量残余应力时释放系数的标定与计算

 <正> 用钻孔法测量残余应力时,使用的释放系数将对构件的残余应力测量精变产生影响。计算释放系数的理论方法有多种。其中普遍应用的公式,是由弹性力学通孔公式推导的应变片中心点处计算式。     

推力矢量飞机的起飞性能研究

简述推力矢量技术的作用,建立了带三轴推力矢量飞机的起飞滑跑段运动方程,通过数值仿真探讨了推力矢量的偏转大小对起飞性能的影响,对不同推力矢量偏转下飞机起飞性能的仿真计算结果进行了分析。仿真结果表明,采用直接力控制可以明显提高飞机的起飞性能。     

地面系留对直升机动力响应的影响

 建立了系留状态下直升机旋翼/机体耦合非线性动力学模型,无铰旋翼简化为当量铰刚性桨叶模型,假定机体是刚性体并受起落架和系留索的约束,系留索静态时松弛并只能承受拉力。采用数值仿真研究了系留对模型旋翼地面共振的影响,对初始扰动和旋翼转速对系统动力学行为的影响也进行了仿真研究。对于无系留的模型旋翼来说,在任何转速下没有出现不稳定现象;地面系留时系统会呈现稳定响应、极限环以及大幅值振荡等非线性动力学行为,大幅值振荡将使系留索、接头和支持结构承受破坏性动力载荷。     

D-最优试验设计在动力调谐陀螺测试中的应用

 为了提高动力调谐陀螺的静态漂移误差测试精度,针对简化静态漂移误差模型,并且考虑陀螺安装角误差的影响,依据D-最优试验设计理论以及正交设计的均匀分散性试验设计思路,设计了一种满足D-最优性质的正交八位置试验方案,并在整个正交空间内采用全局搜索的方法验证了其D-最优性。在相同试验环境下,采用力反馈位置试验法,以全正交空间预测误差平方和最小为评价准则,对该八位置试验方案和国军标GJB1183—91中的八位置试验方案进行比较与评价,试验结果表明该八位置试验方案优于国军标GJB1183—91中八位置试验方案。