高校稳定工作面临的形势与对策

随着我国社会主义市场经济的建立和发展,高校的稳定工作面临着许多新情况、新问题。通过对影响高校稳定诸多因素的分析,提出了当前做好高校稳定工作的途径和方法。     

篦齿封严装置减振方法研究及减振装置设计

本文研究了用于篦齿封严装置的干摩擦式阻尼减振器的减振原理,采用篦齿封严装置气弹稳定性分析方法,分别研究了用于篦齿封严装置的阻尼环和阻尼套筒的减振效果,并在此基础上提出了阻尼减振器的工程设计方法。研究表明,干摩擦式阻尼减振器可以有效地提高篦齿封严装置的气动弹性稳定性。     

飞机语音告警系统的研究

飞机飞行时会出现各种各样的故障，飞行员一般是通过安装在其前下方的告警灯光信号，了解到飞机是哪项系统出现了故障。但是，由于飞行员空中飞行时注意力高度集中，对于告警灯光信号有时会注意不到，或者对众多的告警灯光信号一时分辨不出应归属哪个系统，而不能及时将故障排除造成了严重的飞行事故。如果在飞机上加装语音告警系统，则该系统可将机上告警信号直接输出到飞行员的耳机，用话音来提醒飞行员，     

含硼富燃料推进剂燃烧机理研究

分析了AP包覆硼对含硼富燃料推进剂低压燃烧的影响。通过微热电偶测温和火焰单幅照相技术分别测试含硼富燃料推进剂燃烧波温度分布及燃烧火焰结构；根据气相温度变化的趋势，把该推进剂的气相区燃烧又分为三个子区，并给出了三个子区的厚度，分析了各区温度变化趋势不同的原因。用扫描电镜对熄火表面形貌进行观察，并通过能谱仪进行局部元素分析；该推进剂中断燃烧熄火纵向剖面的实验表明，该推进剂的燃烧表面存在“沉积层”；分析认为该“沉积层”由硼、积炭和少量的三氧化二硼组成，且基本惰性。燃面上“沉积层”的厚度与温度分布曲线中燃面上气相区的厚度基本一致，认为该推进剂的气相反应在燃面上的惰性“沉积层”中进行。     

基于齿数的渐开线直齿轮参数化建模

介绍了在UG环境下渐开线直齿轮参数化建模的方法,分析了不同齿数范围对建模过程的影响,并依据分析结果建立了渐开线直齿轮的两个精确模型,利用这两个模型通过修改参数列表能快捷得到满足任意参数要求的渐开线直齿轮的三维模型。     

基于特征的锻件分类及特征有限元法

综合分析锻件后引入特征技术并归纳锻件的形状及变形特点 ,提出了锻件特征概念并给出锻件形状特征的一般定义和构成 ;采用面向对象技术表示特征 ,提出了锻件特征类的概念模式和具体的参数化数据模型 ;针对有限元分析中复杂多变的约束条件和载荷状况两个关键性因素的表达 ,提出特征类的关联思想。在基于特征的锻件分类基础上 ,把锻件变形归纳为“挤”或“压”两种特征元 ,提出了采用基于特征的有限元法 ,并综合自适应FEM、并行FEM、智能型FEM共同求解大型复杂锻件的变形模拟问题。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

Robust space-time adaptive processing for airborne radar in nonhomogeneous clutter environments

Space-time adaptive processing (STAP) holds tremendous potential for the new generation airborne surveillance radar, in which the phased array antennas and pulse Doppler processing mode are adopted. A new STAP approach using the multiple-beam and multiple Doppler channels is presented here for airborne phased array radar. The approach with space-time multiple-beam (STMB) architecture is robust to array errors and has very low system degrees of freedom (DOFs). Hence, it has low sample support requirement and it is very suitable for the practical planar phased array radar under nonhomogeneous clutter environments. Meanwhile, a new nonhomogeneous detector (NHD) based on the correlation dimension (CD) is also proposed here, which is used as an effective method to screen tracing data prior to detection processing. It can further improve the performance of the STAP approach in the severely nonhomogeneous clutter environments. Therefore, a scheme that incorporates the correlation dimension nonhomogeneity detector (CD-NHD) with the STMB is recommended, which we term CD-NHD-STMB. The experimental simulation results indicate that: 1) the STMB processor is robust to array element error and has high performance under nonhomogeneous clutter environments; 2) the CD-NHD is also effective on the nonhomogeneous clutter. As a result, the CD-NHD-STMB scheme is robust to array element error and nonhomogeneous clutter, and therefore available for airborne phased array radar applications.     

直升机无维修待命时间的理论研究

 <正> 1.引言 国军标《飞机维修品质规范》将“无维修待命时间(t_(al))”列入考核飞机维修品质的重要指标之一,在某些新研直升机的技术指标中已经提出了t_(al)的定量要求。由于该指标能直观地反映直升机的可靠性和维修性水平,所以具有重大的工程意义和实用价值。但是到目前为止理论上尚缺乏深入的研究,工程上也尚未开展该指标的设计和试验。为了给工程设计提供理论依据,本文在理论上对该指标进行了较为深入的研究,用“可靠寿命”的概念阐述了无维修待命时间。     

钛合金板材激光弯曲成形的研究

 对常温下钛合金板材进行了激光弯曲成形研究。分析了激光功率、扫描速度、光斑大小对板材弯曲变形的影响,获得理想工艺参数范围为:功率1 .0～1 .2 k W、扫描速度2～3 m/min、光斑直径6～7mm。同时分析了板材厚度、宽度及扫描次数对材料弯曲变形的影响,为钛合金板材弯曲成形提供了一种新途径。