判断力权值的确定方法及AHP中群组判断矩阵的形成

在ＡＨＰ模型中，请一组专家对某一属性进行评价，根据专家的判断能力，给出判断力权值，再通过适当的数学处理方法，可得最优判断矩阵，这是ＡＨＰ中构造判断矩阵的一种新方法。     

Soft X-ray observations of helmet structures from SXT/Yohkoh

We present soft X-ray observations of helmet structures in solar active regions obtained from SXT/Yohkoh. These helmet structures are observed to form in the flare decay phase and to be associated with active region loop interactions. Their morphology is similar to the much larger scale helmet streamers that appear in the outer corona as shown in optical images of solar eclipse. The observed X-ray helmet structures appear to be in quasi-equilibrium with lifetimes greater than the MHD time scale. Using the filter ratio method for the X-ray observations, we find that the cusp region has lower temperature and higher density than that in the stalk region above it. The plasma pressure in the cusp region is about the same or slightly higher than that in the stalk region.     

3-D position estimation of isolated target and optimal trajectory choice in parasitic synthetic aperture radar

Bistatic SAR (BSAR) systems have recently been the subject of several studies, but little attention has been given to the potential of the location of targets. In the paper, the performance of the estimation of 3-D position of a target (TPE) in parasitic SAR is obtained analytically and illustrated by computer simulation using ambiguity function analysis, and the maximum likelihood estimate (MLE) approach. It was shown that by using a multi look parasitic BSAR all three coordinates of an isolated point target (IPT) could be evaluated. Analytical closed form equations that characterize the measurement accuracy were derived. In the final these equations will be used to demonstrate various cases of more practical, including optimal trajectories choice under any geometry configuration case, moreover, the conclusion is verified via Matlab.     

叉流管－管型换热器二维温度场的数值分析

建立并导出叉流管－管型换热器传热过程的二维数学模型及相应的差分格式。对比实验数据和性能计算结果，表明数值方法是有效可行的，据此编制的计算机程序已成功地用于组合发动机空气预冷换热器工作过程的预测。     

弹翼对旋成体底部流动的影响

本文利用压强测量及纹影观测技术研究弹翼对旋成体底部流动及底阻的影响，研究对象包括有无收缩船尾的两种后体，并同时测量了模型的底面和侧面压强分布，通过实验观测结果和理论分析，得到较细致的弹翼干扰结果，有助于进一步认识底部注以动特性及上游干扰，对飞行器设计有实用意义。     

重复热处理工艺对30CrMnSiA钢疲劳性能的影响

本文介绍了30CrMnSiA钢的九种不同的重复热处理工艺,结果显示B种热处理工艺能使30CrMnSiA钢具有最佳的抗疲劳性能并证明不同的重复热处理状态对钢的疲劳性能有影响.     

Adaptive control for a sensorless permanent-magnet synchronousmotor drive

An adaptive velocity controller for a permanent-magnet synchronous motor without using shaft sensor is presented. Two line-to-line voltages and two stator currents are sensed to produce the flux position. The design part is concerned with the formulation of control algorithm for current-regulated pulsewidth modulated inverter and vector control strategy for speed loop. Under the vector control framework, self-tuning, model following, and model referencing adaptive control are applied to design for the speed-loop controllers. The implementational part integrates the control of current and speed loop using microprocessor-based controllers. Experimental case studies that correlate simulation and measurement results are provided. The experimental results validate the theoretical development. A new approach for designing advanced adaptive controller for a sensorless ac drive is provided     

条形码在机房管理系统中的应用

文章介绍了基于条形码技术的机房管理系统的网络构建及其功能模块设计，以及条形码在系统设计中的技术实现。     

基于DSM的型号研制项目过程建模

通过分析型号研制项目活动之间的关系,建立了基于DSM的型号研制项目过程结构化模型,给出了具体实现项目过程的DSM方法,包括活动分解、耦合活动集的识别和耦合活动集的解耦方法,实现了型号研制项目过程的优化重组,最后,通过一个实例说明了该建模方法的实用性和有效性.     

PLM支持下的数字化制造

越来越多的制造企业从长远发展的战略考虑,精心规划和积极构建企业信息系统集成框架,为深化企业信息共享.推动企业创新打基础.传统的制造行业,特别是装备制造业,在PLM战略支持下的数字化制造平台,将给企业创新添加新的活力.