TiAl金属间化合物缺口断裂性能

 TiAl合金作为准脆性材料,在其服役过程中由于缺口的存在使得断裂对缺口非常敏感,严重降低了其使用性能,因此需要研究TiAl合金在缺口作用下的断裂性能。采用带缺口的组合拉伸试样研究了温度和拉伸速率对具有近全片层组织Ti-48Al-2Cr-2Nb合金缺口断裂性能的影响。结果表明,室温下TiAl合金对缺口非常敏感,随着温度的升高,TiAl合金对缺口敏感性降低,当温度为800 ℃时,TiAl合金对缺口不敏感。TiAl合金在低温区塑性变形是通过位错滑移和变形孪晶引起的,高温下是由扩散控制的位错攀移作用引起的。研究还表明,200 ℃下拉伸速率较低时TiAl合金对缺口不敏感,当拉伸速率增加到较高时,TiAl合金对缺口很敏感。     

固体火箭发动机长尾喷管烧蚀实验研究

通过研究长尾喷管烧蚀机理,建立了一套模拟长尾喷管烧蚀的实验方法,设计了研究长尾喷管发动机烧蚀性能的实验装置,并进行了正常状态和过载状态下的长尾喷管烧蚀实验,同时获得了烧蚀实验数据及烧蚀形貌。通过建立的数值计算模型,开展了对长尾喷管烧蚀的数值计算研究。将实验结果与数值模拟结果进行了对比分析,两者在一定程度上吻合较好,从一个侧面验证了数值模拟的有效性。     

基于希尔伯特-黄算法瞬时测频的DSP实现

文章阐述了希尔伯特-黄瞬时测频技术的基本原理,介绍了希尔伯特．黄瞬时测频算法的DSP软件实现,包括系统软件设计框架介绍、子系统任务划分、DSP／BIOS的应用、BOOT模块、数据处理模块和HPI模块等内容,并给出了实际系统的性能分析。     

风洞分布式支撑天平测力试验技术研究

采用双尾支撑测量形式的加工、装配误差会使系统内应力过大,影响测量精度。针对某“双机身”飞机CTS 风洞试验气动力测量需求,发展基于多维力天平内置的风洞分布式支撑天平测力试验技术;研制具有消除系统内应力功能的双支撑系统,提出两种6 分量双支撑天平校准及测力方法,并对数据处理和双支撑系统可靠性进行检验加载、对比分析和验证。结果表明：风洞分布式支撑天平测力试验技术能够有效消除双支撑天平系统由于过约束而导致的固有装配内应力,双支撑天平系统各部分连接、测量可靠;两种校准测力方法测量精度相当,均能达到单台应变天平测量误差水平,可满足风洞试验测量精度需求;综合考虑现有校准设备校准能力,最终采用“合成式校准测力”方法进行的风洞试验,获得了满意的试验测力精度。     

Form-finding methods for deployable mesh reflector antennas

Deployable high-frequency mesh reflector antennas for future communications and obser- vations are required to obtain high gain and high directivity. In order to support these new missions, reflectors with high surface accuracy are widely required. The form-finding analysis of deployable mesh reflector antennas becomes more vital which aims to determine the initial surface profile formed by the equilibrium prestress distribution in cables to satisfy the surface accuracy requirement. In this paper, two form-finding methods for mesh reflector antennas, both of which include two steps, are pro- posed. The first step is to investigate the prestress design only for the cable net structure as the circum- ferential nodes connected to the supporting truss are assumed fixed. The second step is to optimize the prestress distribution of the boundary cables connected directly to the supporting truss considering the elastic deformation of the antenna structure. Some numerical examples are carried out and the simulation results demonstrate the proposed form-finding methods can warrant the deformed antenna reflector surface matches the one by design and the cable tension forces fall in a specified range.     

Passive inter-modulation scattering analysis of reflector considering contact nonlinearity

 Passive inter-modulation (PIM) is a form of nonlinear distortion caused by the inherent nonlinearities of the passive devices and components in RF/microwave system. It will degenerate the performance of communication system with broad-band channel and high-sensitivity receiver. Therefore, it is necessary to construct a model to simulate this process in order to predict the level of PIM. This paper is aimed at constructing some plate models with one-dimensional and two-dimensional contact nonlinearity sections illuminated by two-tone waves, and calculating the scattered field at a fixed-point in space using time-domain physical optics method. By taking fast Fourier transform (FFT), we get the spectrum of the scattered field and then analyze the generated PIM products. At the end of this paper, some numerical examples are presented to show the influence rules of the relative factors on PIM. The results indicate the variation of the level of PIM with the number of the nonlinear regions, the nonlinear spacing, and the incident power levels.     

“动中通”三轴天线跟踪机理研究

基于捷联跟踪式三轴天线“动中通”系统推导了天线姿态角求解算法,并且定义了天线俯仰角和方位角范围。针对工程中出现的三轴天线“动中通”系统在低纬度地区跟踪卫星时天线方位角跳变的情况,在理论分析的基础上结合仿真得出了天线姿态角突变的机理。由于卫星矢量在车体系内水平两个坐标分量的符号会出现改变,从而引起天线方位角的突变,引起伺服系统驱动能力不足,致使跟踪中断。最后针对该问题设计了两种解决方案。     

Experimental investigation on deformation behavior of TJ-1 lunar soil simulant subjected to principal stress rotation

The knowledge of mechanical properties of lunar soil is of fundamental importance for the coming exploration of the Moon. This paper aims to investigate the fundamental deformation behavior of lunar soil and the effects of the intermediate principal stress coefficient, deviatoric stress ratio, and mean stress during the principal stress rotation. First, an improved technique was proposed to generate homogeneous samples based on the Multi-layer Undercompaction Method. Second, three series of tests on TJ-1 lunar soil simulant under the principal stress rotation were performed with a hollow cylinder apparatus at Tongji University, China. In each series of tests, only one value of the three variables mentioned above was changed while the others were kept constant. The test results demonstrate that the rotation of principal stress can result in significant plastic deformation, volumetric strain, and non-coaxiality (non-coincidence of the increment direction of principal plastic strain with the principal stress direction) of TJ-1 lunar soil simulant. In addition, it is found that the intermediate principal stress coefficient, deviatoric stress ratio, and mean stress have different influences on the four strain components, i.e. _εz,_εr,_εθ${\epsilon }_z\text{,}{\epsilon }_{\text{r}}\text{,}{\epsilon }_{\theta }$ and _γzθ${\gamma }_{z\theta }$, volumetric strain, and non-coaxiality during the principal stress rotation. The influence of deviatoric stress ratio is relatively stronger than the others. Therefore, the influence of principal stress rotation on the deformation behavior of lunar soil should be taken into account carefully in the design and construction of facilities on the lunar surface in the future.     

薄壁铸件基准面加工工装改进

针对薄壁铸件精基准面机械加工精度低、变形大的问题,分析了工装改进的原因,对工装的主要结构进行了改进,并以实例辅助说明,改进后的工装应用效果良好。     

飞行器轨迹优化方法综述

飞行器轨迹优化是飞行器总体设计的关键环节,特别是在现代空间飞行器和高超声速飞行器设计过程中发挥着重要作用.在全面调研国内外现有轨迹优化技术的基础上,提出了飞行器轨迹优化新的分类方式,概述了多种飞行器轨迹优化的原理和应用,并详细分析了各自的优缺点和发展趋势.最后介绍了现在实际应用的多种轨迹优化软件.