航空发动机风扇转子叶片外物损伤I.鸟撞击试验研究(英文)

本文改进了叶片鸟撞击试验条件。对某型发动机风扇一级转子叶片进行了鸟撞击试验。通过对叶片的鸟撞击瞬态响应分析和撞击前后叶片叶型变化的分析,验证了风扇一级转子叶片的抗鸟撞击性能,为某型发动机风扇转子叶片的抗外物损伤设计提供了依据。     

民机的一种新型布局形式——翼身融合体飞机

 讨论了一种区别于机翼与圆柱机身的传统民机外形——翼身融合体（BWB）外形。从给定容积下减少浸润面积和摩擦阻力的考虑发展出了翼身融合体的概念。在满足系列设计约束条件下讨论了适于大型（800座）客机的翼身融合体的技术和商业上的可能性。概念设计研究表明,翼身融合体外形可获得比常规外形更好的性能。巡航升阻比可从传统外形的19提高至23。480座的BWB外形与同量级的传统外形（A380-700）相比,最大起飞重量可减少18%,每座位燃油消耗可减少32%,具有良好的环保性。通过气动载荷分布规律的反设计,翼型修型和三维优化设计等气动设计方法可以有效减阻和提高BWB的气动性能。由于BWB的高度融合性,讨论了多学科优化设计方法的重要性和有效性。BWB概念能够发展成BWB系列机,进一步提高巡航马赫数也是可能的。     

Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.     

旋转机翼悬停气动特性研究

鸭式旋转机翼(CRW)是一种先进的高速直升机方案,旋翼同时也是机翼,是其最关键气动部件之一。采用结构分区拼接网格技术进行空间离散,分区建立参考系,通过求解多重参考系下的N-S方程来计算旋翼流场,首先以传统的Caradonna-Tung实验旋翼的亚、跨声速悬停流场分析为例验证该方法的可靠性,进而采用该方法对旋转机翼悬停流场进行了数值计算,旋翼拉力计算值和地面实验值吻合较好,结果分析表明旋转机翼的悬停流场有着不同于传统旋翼的流场特性。     

Robust fault-tolerant control for wing flutter under actuator failure

Many control laws, such as optimal controller and classical controller, have seen their applications to suppressing the aeroelastic vibrations of the aeroelastic system. However, those control laws may not work effectively if the aeroelastic system involves actuator faults. In the current study for wing flutter of reentry vehicle, the effect of actuator faults on wing flutter system is rarely considered and few of the fault-tolerant control problems are taken into account. In this paper, we use the radial basis function neural network and the finite-time H_∞ adaptive fault-tolerant control technique to deal with the flutter problem of wings, which is affected by actuator faults, actuator saturation, parameter uncertainties and external disturbances. The theory of this article includes the modeling of wing flutter and fault-tolerant controller design. The stability of the finite-time adaptive fault-tolerant controller is theoretically proved. Simulation results indicate that the designed fault-tolerant flutter controller can effectively deal with the faults in the flutter system and can promptly suppress the wing flutter as well.     

基于人机闭环稳定性的舵机速率限制边界

舵机速率限制是造成电传操纵飞机人机耦合的主要原因。利用描述函数法对舵机速率限制非线性进行建模,分析舵机速率限制非线性、人机耦合发生频率及人机闭环稳定性间的关系,并基于此提出舵机速率边界的确定方法;以典型放宽静稳定性飞机为例,基于最优McRuer驾驶员模型,确定人机闭环稳定性所需的最小舵机偏转速率;基于开环起始点(OLOP)准则对所确定的速率限制边界进行验证。结果表明:本文提出的舵机速率边界的确定方法最小成本地避免了人机耦合;所确定的舵机速率限制边界与OLOP准则边界对应的舵机速率基本吻合,即所建立的舵机速率限制边界确定方法合理。     

电缆故障在线检测定位装置研究

电缆作为飞机电源系统的重要组成部分,实现电缆故障的在线诊断,可以提高其可靠性。采用扩展频谱时域反射法(SSTDR),基于FPGA技术,设计一种板级速率为500 MHz的飞机电缆故障在线检测和定位装置,并进行实验验证。结果表明:该装置能够实现电缆开路、短路以及间歇性电弧的在线检测和定位,具有定位精度高、实时性好等优点;利用该装置在线监测电缆的健康状态,实现难以复现的间歇性故障的检测,能够提高地面运营、维护效率,节省人力物力,具有较高的工程应用价值。     

考虑燃料雾化的气液两相连续旋转爆轰数值模拟

为研究气液两相连续旋转爆轰发动机燃烧室内爆轰波的传播特性,以汽油为燃料,富氧空气为氧化剂,建立了欧拉-拉格朗日模型进行二维数值仿真,其中气相方程采用时空守恒元与求解元方法求解,液相方程采用标准四阶龙格库塔法求解。在两相旋转爆轰模型还考虑了液滴雾化破碎过程。计算结果表明：起爆后形成的初始爆轰波经过初始燃料填充区域后逐渐衰减,随后入口附近新生成的压力波经过一系列发展形成了自持稳定传播的旋转爆轰波;旋转爆轰波的传播模态受燃料与氧化剂的喷注压力和氧化剂填充比影响,在不同工况下旋转爆轰波呈现出4种传播模态,即稳定单波模态、稳定双波模态、不稳定双波模态和不稳定单波模态;在双波模态工况下,燃烧室内初始只形成1个爆轰波,后由入口附近局部爆炸产生的压力波发展为新的爆轰波,转化为双波模态后爆轰波的强度略有下降,但燃烧室整体推力更加平稳。     

具有不确定参数的机器人鲁棒轨迹跟踪控制

研究了具有不确定参数的机器人轨迹跟踪控制问题。提出了一种鲁棒控制方案,它由改进力矩发生器和鲁棒补偿器组成,理论分析及仿真实验表明,该控制方案具有较好的跟踪性能。