新建他激反激变换器方程及其解析解

引用文 [1 ]的思路 ,寻找他激反激变换器的运行状态特征参量 (磁通密度增量、剩余磁通密度和占空比 )与构成这一变换器的基本物理参量之间的函数关系。首先阐明由于频率给定 ,他激反激变换器稳态运行时会出现无剩磁工况和有剩磁工况两种。而后确定这两种工况下 ,磁路等效储能空间单位体积每个周期的传输能量 (命名为“磁能传输密度”)。在这基础上 ,分别建立和解出他激反激变换器在不同工况下稳定运行时应满足的方程。最后根据所得的解析解阐明这种变换器的特性。本文和文 [1 ],以磁路分析为基础建立了一种新的反激变换器理论。     

Steady-state analysis and design of a switched-capacitor DC-DCconverter

A representative switched-capacitor DC-DC converter topology is presented, circuit operation is explained, and control strategies are identified. State-space averaging is used to analyze steady-state performance and to develop control criteria and design equations. The analytical results are verified by SPICE simulation     

The Freja ultraviolet imager

Auroral images acquired by satellite instrumentation have proven to be a crucial component of the scientific equiry into the physical processes of the Earth's magnetosphere. TheFreja mission provided an opportunity to extend these measurements into the temporal and spatial regime commonly associated with ground-based optical imagers. Employing the basic procedure used successfully in theViking program allowed image repetition rates of 6 s to be achieved with simultaneous exposure of all pixels within the field-of-view. Typical exposure times of 0.3 s required development of an improved image intensifier system and operational requirements resulted in image formats covering approximately one-third of a spin. Simultaneously exposing two broad-band UV cameras, the instrument generates in its normal operational mode 264.6 kbytes per image pair. Results from initial operations confirm the design approach and suggest such imagers can be routinely included on challenging low cost missions such asFreja.     

Implementation of hand geometry: an analysis of user perspectives and system performance

This discusses the implementation issues of installing a commercially available hand geometry system in the current infrastructure of Purdue University's Recreational Sports Center. In addition to a performance analysis of the system, a pre- and post-data collection survey was distributed to the 129 test subjects gathering information on perceptions of biometrics, in particular hand geometry, as well as participants' thoughts and feelings during their interaction with the hand geometry device. The results of the survey suggest that participants were accepting of hand geometry. Additionally, analyses of the participants' survey responses revealed that 93% liked using hand geometry, 98% thought it was easy to use, and 87% preferred it to the existing card-based system, while nobody thought the device invaded their personal privacy. System performance achieved a 3-try match rate of 99.02% (FRR 0.98%) when "gaming"/potential impostor attempts were removed from analysis. The failure to enroll rate was zero. Statistical analyses exposed a significant difference in the scores of attempts made by users with prior hand geometry usage, and subjects that could not straighten out their hand on the device. However, there were no statistical difference in the effects of rings/no rings, improper hand placements/proper hand placements, or gender on hand geometry score.     

Rationale for the development of the UK defence standards forsafety-critical computer software

Changes in the procurement environment and developments in technology that will require the adoption of new development certification procedures within the next few years are examined. Characteristics of safety-critical computer systems and the safety problems posed by digital computers are described. The way in which the changes have influenced the preparation of the new draft defence standards offered for public debate in the UK prior to their formal adoption by the Ministry of Defence is discussed. Principle features of the future safety-critical systems policy are outlined. The use of Ada for safety-critical software is considered     

Dose equivalent, absorbed dose and charge spectrum investigation in low Earth orbit.

Particle intensity, dose equivalent and absorbed dose have been measured on board the space shuttle Endeavour during STS-108 in December 2001 by Dublin Institute for Advanced Studies (DIAS). The dose estimates are based on very accurate measurements of recoils produced in CR-39 by cosmic ray primary and secondary protons and heavier nuclei and by secondary neutrons. The corresponding LET spectra were used to determine dose equivalent and absorbed dose values. Estimates of the total flux of Z > or = 2 nuclei have been undertaken and a preliminary charge spectrum was measured. Some comparisons are made with preliminary data obtained on STS-105 (ISS Expedition) and other missions using CR-39 detectors.     

Family of constrained signal detectors for hyperspectral imagery

Generalized likelihood ratio tests (GLRTs) are derived for the problem of detecting targets in hyperspectral images. These detectors are derived under the assumptions that the signals from the materials in the image mix linearly and that the noise in the system is Gaussian. It is also assumed that the abundances of the signals from the various materials in a pixel must sum to one. This constraint models the fact that the material abundances in a pixel are just the fraction of the pixel that they occupy. Under these assumptions, detectors are derived which outperform the detectors derived without the sum-to-one constraint.     

Nanotechnology-based molecular test equipment (MTE)

This paper describes original research efforts in the design, simulation, and development of nanotechnology-based molecular test equipment (MTE). This is a research effort for testing printed circuit boards independent of traditional automatic test equipment (ATE) through the fabrication of MTE within integrated circuits (ICs). The MTE is embedded within the IC substrate and encapsulated within nanoprobes that connect between the surface and the substrate of the IC at various functional areas. A process is followed whereby IC device simulation is performed to assess the electrical, chemical, and structural properties of integrated and adjacent substrate devices. Through this approach the nominal and failed device performance parameters of interest to substrate-based MTE are found. Discussion of the development and application of MTE within IC architectures is provided, including such topics as the effect of substrate composition on the design and realization of MTE, interfaces between MTE and IC devices, and reporting of MTE results to the IC surface and technician. Potential application areas within different device functions will also be identified. A chemical structure diagram is also provided to illustrate the implementation of MTE using discrete device configurations with MTE-augmented logic