Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

Coupling damage and reliability model of low-cycle fatigue and high energy impact based on the local stress–strain approach

Fatigue induced products generally bear fatigue loads accompanied by impact processes,which reduces their reliable life rapidly. This paper introduces a reliability assessment model based on a local stress–strain approach considering both low-cycle fatigue and high energy impact loads.Two coupling relationships between fatigue and impact are given with effects of an impact process on fatigue damage and effects of fatigue damage on impact performance. The analysis of the former modifies the fatigue parameters and the Manson–Coffin equation for fatigue life based on material theories. On the other hand, the latter proposes the coupling variables and the difference of fracture toughness caused by accumulative fatigue damage. To form an overall reliability model including both fatigue failure and impact failure, a competing risk model is developed. A case study of an actuator cylinder is given to validate this method.     

Friction moment analysis of space gyroscope bearing with ribbon cage under ultra-low oscillatory motion

This paper presents the model of calculating the total friction moment of space gyroscope ball bearings which usually work under ultra-low oscillatory motion and are very sensitive to the friction moment. The aim is to know the proportion of the friction moment caused by each frictional source in the bearing＇s total friction moment, which is helpful to optimize the bearing design to deduce the friction moment. In the model, the cage dynamic equations considering six degree-of-freedom and the balls dynamic equations considering two degree-of-freedom were solved.The good trends with different loads between the measured friction moments and computational results prove that the model under constant rate was validated. The computational results show that when the speed was set at 5 r/min, the bearing＇s maximum total friction moment when oscillation occurred was obviously larger than that occurred at a constant rate. At the onset of each oscillatory motion, the proportion of the friction moment caused by cage in the bearing＇s total friction moment was very high, and it increased with the increasing speed. The analyses of different cage thicknesses and different clearances between cage pocket and ball show that smaller thickness and clearance were preferred.     

带迎角钨杆斜侵彻铝板数值仿真研究

为研究迎角对钨杆斜侵过程的影响,开展了带迎角钨杆斜侵彻铝板数值仿真研究。仿真中采用SPH方法,Shock状态方程和Steinberg本构模型。钨杆共有两种尺寸,分别为Φ10mm×23mm和Φ10mm×46mm。铝板厚10mm,撞击速度为2km/s,撞击角度为60°。为简化分析,将迎角分解为俯仰角和偏航角,其中俯仰角范围为-90°～90°,偏航角范围为0°～90°。对钨杆侵彻过程的分析结果表明：斜侵彻存在临界迎角,在临界迎角范围内钨杆所受力矩可忽略不计;在临界迎角范围外,钨杆将发生弯曲甚至折断。对钨杆的剩余质量分析结果表明：当偏航角为0°且钨杆未折断时,剩余质量只在较小的范围内变化;当俯仰角为0°时,剩余质量随迎角增加线性减小。对钨杆的剩余速度分析结果表明：偏航角对剩余速度的影响与俯仰角对剩余速度的影响基本一致,剩余速度曲线关于0°迎角基本对称。根据仿真结果,采用曲线拟合的方法给出了钨杆斜侵彻铝板的剩余速度经验公式。     

复合材料夹层结构在航空领域的应用

详细描述了复合材料夹层结构及几种常用芯材的性能特点,综合分析了复合材料夹层结构在飞机上的应用案例,对各种夹层结构芯材成型工艺的重点、难点进行了探析,得到了复合材料夹层结构的性能概况及使用工艺要求,可为复合材料夹层结构设计、制造提供参考。     

多段翼混合边界层改变对流场的影响研究

前缘缝翼尾流与主翼边界层混合的改变对主翼气动力具有重要影响.利用数值模拟手段,通过在前缘缝翼尾缘添加一定动量系数的喷流,改变前缘缝翼尾缘的尾流,进而改变尾流与主翼边界层的混合状况.求解二维多段翼模型30P30N在各个不同喷流条件下的二维非定常流场,结果表明:提高前缘缝翼尾缘喷流的动量系数,将使前缘缝翼尾流和主翼边界层混合开始点后移,提高主翼上表面负压峰值和主翼升力;混合开始点对主翼的负压峰值及升力均有一定的影响;增大来流攻角会抑制前缘缝翼尾流和主翼边界层的混合.     

基于NESO的高超声速拦截弹解耦控制研究

针对高超声速拦截弹姿态控制问题,提出了基于非线性扩张状态观测器(NESO)的解耦控制方法.根据Tornambe的分散鲁棒控制理论,把耦合项和不确定性视为广义不确定项,构造基于NESO的估计和补偿信号并加入到闭环控制律中.理论推导证明了该方法可以保证闭环系统跟踪误差一致有界.在高超声速拦截弹模型上进行了仿真验证,并与传统的分通道反馈控制方法进行对比,结果表明所设计解耦控制方法得到了更好的控制效果,在较大程度上消除了通道耦合和不确定性的影响.     

一种减小再入飞行器侧向气动非线性的布局优化方法

为改善升力式再入飞行器在跨声速段出现的侧向气动特性非线性问题,发展了一种基于Kriging代理模型的自适应迭代气动布局优化方法.设计了一种常规升力式再入飞行器布局,计算了该布局在跨声速段的侧向气动力,分析了可能影响侧向气动特性的机翼布局参数.根据气动布局优化流程,计算了气动布局样本气动特性,建立了布局参数到侧向力矩系数...     

阳极氧化对TiAl合金高温氧化行为和力学性能的影响

采用电化学阳极氧化技术在含NH4F的乙二醇电解液中对TiAl合金进行阳极氧化处理。研究阳极氧化对TiAl合金高温氧化行为和力学性能的影响。结果表明:由于“卤素效应”,阳极氧化处理的TiAl合金经高温氧化后表面形成致密、连续的Al₂O₃氧化膜,有效阻止了氧的内扩散,进而显著提高合金的抗高温氧化性能。经1000℃氧化100 h后,阳极氧化试样增重由未经阳极氧化处理试样的85.86 mg/cm²降至0.67 mg/cm²。另一方面,阳极氧化TiAl合金表面硬度和弹性模量随高温氧化时间延长呈先降低后升高的趋势。阳极氧化TiAl合金在高温服役后,合金的摩擦系数较未经阳极氧化处理试样上升,但表面耐磨性先降低后升高。这是由于TiAl合金经阳极氧化后,表面形成了一层富铝含氟氧化膜,由于氧化膜中F元素在高温氧化过程中与Ti、Al结合形成卤化物,卤化物蒸气选择性扩散在原始氧化膜处形成致密的Al₂O₃保护膜。阳极氧化对TiAl合金力学性能的影响主要是由于氧化膜中Al₂O₃的含量变化所致。     

基于自适应代理模型的结构动力可靠度分析方法

结构动力可靠度分析对于衡量结构的安全状态和工作性能具有重要的指导意义。采用一种同时考虑 动态激励载荷和材料力学性能参数随机性的动力可靠度计算高效方法,通过建立不确定性材料力学性能参数 与条件动力可靠度之间的 Kriging代理模型,推导动力可靠度的解析表达式;提出一个新的学习函数来构建自 适应的 Kriging代理过程,通过复合材料飞行器蒙皮骨架结构在随机振动载荷和随机材料力学性能参数共同作 用下的动力可靠度分析对所提方法的准确性与高效性进行验证。结果表明:所提方法不仅能够避免使用代理 模型对动力可靠度求解时由于使用数值积分所引入的误差,同时能够使用尽可能少的计算成本获得准确的动 力可靠度结果。