复杂结构振动的一种超单元简化分析

本文提出了一种建立在常规有限元模型上的超单元分析方法,对复杂结构的振动分析进行降阶简化处理。这种方法是把结构重新以超单元形式划分,在超单元内部采用了简化的动减缩方法;边界上则采用局部位移场重新插值方法,或采用局部刚化的方法。由超单元组装得到的总体矩阵仍具有对称、稀疏等性质,得到的动力学方程仍具有常规形式。这种超单元分析方法不但大大降低了求解模型的阶次,扩大了求解能力,而且易于编程,求解方便。文中还通过摄动分析讨论了内部模态截取准则,以保证求解的有效性和可靠性。数值算例表明,本文方法是很有效的,且具有较高的求解精度。     

铅化合物在双基推进剂燃烧过程的作用机理

本文提出了铅化合物催化双基推进剂燃烧的反应历程。充分说明这类化合物是最终通过提高燃烧表面处嘶嘶区温度梯度提高燃速的。本文还提出了“铅化合物有通过增加燃烧表面上碳质物量增加燃速的一面,还有通过减少碳质物抑制燃速增加的一面”这一新的论点及抑制碳质物增加的反应并阐明了压力对这种抑制能力的影响。最后根据本文提出的作用机理及传热原理圆满解释了超速、平平和/或麦撒效应。     

燃气源控制气流绝热热流数值模拟

提出了一种新的求解复杂稳态全速度统一流场的方法,即先采用PISO算法计算一假想的非稳态流场用以获得一时间点上的流场参数分布,然后将这一时间点上的流场参数作为初场,用SIMPLE算法进行稳态流场的计算,进而得到较满意的收敛结果。用这种方法计算了某燃气源控制气流在假定固体壁面为绝热边界的条件下的三维热流流场,得到了流场的各参量分布情况,并与冷流的计算结果进行了比较分析。     

静止图象的多值分块编码

本文在分析二值分块编码分块效应的基础上,提出了一种新的多值分块编码方法。理论分析与实验结果均表明该方法使编码图象的分块失真减小到几乎不能察觉,输出码率降低到1.36比特/象素左右,而且文中提出的分类算法十分简便。     

空间科学实验机器人辅助遥操作系统

建立了一个面向空间舱内晶体生长科学实验的地面模拟机器人遥操作系统。该系统通过基于虚拟现实的预测仿真来克服通讯时延的影响，并通过仿真图形和实际视频图像的叠加来对虚似仿真环境进行校准，以提高预测仿真的保真性。操作员利用空间鼠标等人机交互工具实时控制仿真机器人系统的运动，通过遥控与自主相结合的方式，并借助全局和局部视觉信息，完成了在空间晶体生长科学实验中更换晶体炉料棒的作业任务。     

静止气象卫星测距系统及测距信号的应用

简要介绍日本静止气象卫星(GMS)的三点测距系统以及侧音测距的基本原理,利用静止气象卫星测距信号进行时间比对同步实验。最后展望了利用我国静止气象卫星开展时间比对和发播工作的设想。     

Experimental study of hydrogen-rich/oxygen-rich gas-gas injectors

Five types of coaxial injectors were investigated experimentally using hot hydrogen-rich gas and oxygen-rich gas, which were respectively provided by a GH2/GO2 hydrogen-rich perburner and a GH2/GO2 oxygen-rich preburner. The injectors were the shear coaxial injector, the oxidizer post expansion coaxial injector, the fuel impinging coaxial injector, the central body coaxial injector, and the shear tri-coaxial injector. The characteristic velocity efficiency and the combustor＇s wall temperatures were obtained for different design parameters through the experiments. It can be con- cluded that angles of the oxidizer post expansion and the fuel impinging have little influence on the combustion performance and the wall temperatures. The contact area between fuel and oxidizer and the mass flow rate have significant impacts on the combustion performance. The shear tri-coaxial injector has the best combustion performance but also the highest wall temperatures among the five types of injectors.     

Motion prediction of a non-cooperative space target

Capturing a non-cooperative space target is a tremendously challenging research topic. Effective acquisition of motion information of the space target is the premise to realize target capture. In this paper, motion prediction of a free-floating non-cooperative target in space is studied and a motion prediction algorithm is proposed. In order to predict the motion of the free-floating non-cooperative target, dynamic parameters of the target must be firstly identified (estimated), such as inertia, angular momentum and kinetic energy and so on; then the predicted motion of the target can be acquired by substituting these identified parameters into the Euler’s equations of the target. Accurate prediction needs precise identification. This paper presents an effective method to identify these dynamic parameters of a free-floating non-cooperative target. This method is based on two steps, (1) the rough estimation of the parameters is computed using the motion observation data to the target, and (2) the best estimation of the parameters is found by an optimization method. In the optimization problem, the objective function is based on the difference between the observed and the predicted motion, and the interior-point method (IPM) is chosen as the optimization algorithm, which starts at the rough estimate obtained in the first step and finds a global minimum to the objective function with the guidance of objective function’s gradient. So the speed of IPM searching for the global minimum is fast, and an accurate identification can be obtained in time. The numerical results show that the proposed motion prediction algorithm is able to predict the motion of the target.     

国内外宇航用电连接器典型标准的分析与研究

分析MIL、NASA、ESA的典型电连接器标准的主要特点,简介我国最新制定的QJ 10008-2008<宇航用低频圆形电连接器通用规范>的主要内容,并通过与国外宇航用电连接器标准的对比分析,提出我国航天用电连接器的发展方向.