3-D position estimation of isolated target and optimal trajectory choice in parasitic synthetic aperture radar

Bistatic SAR (BSAR) systems have recently been the subject of several studies, but little attention has been given to the potential of the location of targets. In the paper, the performance of the estimation of 3-D position of a target (TPE) in parasitic SAR is obtained analytically and illustrated by computer simulation using ambiguity function analysis, and the maximum likelihood estimate (MLE) approach. It was shown that by using a multi look parasitic BSAR all three coordinates of an isolated point target (IPT) could be evaluated. Analytical closed form equations that characterize the measurement accuracy were derived. In the final these equations will be used to demonstrate various cases of more practical, including optimal trajectories choice under any geometry configuration case, moreover, the conclusion is verified via Matlab.     

叉流管－管型换热器二维温度场的数值分析

建立并导出叉流管－管型换热器传热过程的二维数学模型及相应的差分格式。对比实验数据和性能计算结果，表明数值方法是有效可行的，据此编制的计算机程序已成功地用于组合发动机空气预冷换热器工作过程的预测。     

Adaptive control for a sensorless permanent-magnet synchronousmotor drive

An adaptive velocity controller for a permanent-magnet synchronous motor without using shaft sensor is presented. Two line-to-line voltages and two stator currents are sensed to produce the flux position. The design part is concerned with the formulation of control algorithm for current-regulated pulsewidth modulated inverter and vector control strategy for speed loop. Under the vector control framework, self-tuning, model following, and model referencing adaptive control are applied to design for the speed-loop controllers. The implementational part integrates the control of current and speed loop using microprocessor-based controllers. Experimental case studies that correlate simulation and measurement results are provided. The experimental results validate the theoretical development. A new approach for designing advanced adaptive controller for a sensorless ac drive is provided     

氦气驱动预压涡轮泵启动初期反流问题分析

用于某液体火箭发动启动动系统的气驱预压涡轮泵在起动初期出现了气体反流,导致预压泵呈夹气状态,对发动启动动过程控制不利。根据驱动试验系统原理,在MWorks平台中对驱动过程进行了仿真。对预压泵采用了Suter全特性表达式,对涡轮管路及排放路分别建立了描述排空与两相流动过程的简化数学模型。结果 表明,导致反流的原因为涡轮入...     

航天器弹性附件伸展动力学研究

利用动量矩定理推导出带伸展弹性板航天器的姿态动力学方程，在弹性板等速伸展的情况下，导出板的振动与伸展运动耦合微分方程，航天器姿态运动与板的伸展运动、振动耦合微分方程，通过龙格－库搭积分法得出了数值解，结果表明：弹性板等速伸展时，其振动的振幅随板长度的增长而增大，航天器姿态角速度随板长度的增长而减少。弹性板等速率越大，板振动的振幅越大。     

Distributed computation for a tree network with communicationdelays

Tree networks of communicating processors are examined with the objective of solving a computational problem in a minimal amount of time. The processors in the networks may be equipped either with or without front-end processors for communicating of loading. The determination of the optimal division of processing load is discussed for the network with and the network without front-end processors. The inclusion of solution time, the time taken for sensors to report the solution back to originator, is discussed     

细晶铸造对K418合金拉伸性能的影响

测试了不同温度下细晶铸造和普通铸造Ｋ４１８合金的拉伸性能。结果表明，细晶铸造明显改善了合金的极限位伸强度和屈服强度，室温和６００℃的合金拉伸强度和晶粒平均直径符合Ｈａｌｌ－Ｐｅｔｃｈ关系。     

ADμC824在温度测控方面的应用

介绍了ADμC824的部分特性及其在精确控温方面的软硬件设计思路。     

TEMPERATURE EFFECT ON OXIDATION PROTECTION LIFE OF MULTI-LAYER COATING FOR C/C COMPOSITES

Carbon-carboncomposites(C/C)exhibitexcellentstructuralpropertiesabove165OC,andareconsideredasthemostpromisingcandidatematerialsforthehighthrust-weightratioturbineengines.Asakeytechnologyforthehigh-temperaturestructuralapplicationsofC/C,oxidationprotectionispaidmoreandmoreattentionrecently.TheoxidationprotectionllfeofacoatedC/Cisdeterminedbyenvironmenta1temperature,becauseitnotonlydecidesthether-mochemicalconditionsofinterfacesinacoating,butalsocontrolsthedynamicprocessofoxy-gendiffusion.The…     

高精度稠粘流体压力传感器

一种高精度流体压力传感器,这种传感器除适用于测量普通气体、液体的压力外,特别适用于稠粘流体的压力测量。文中着重阐述了这种传感器的工作原理、结构特点及性能指标,并简要介绍了设计中的一些考虑,指出了这种传感器的发展潜力和应用前景。