A New D-GCL for Unidirectional Motion with Large Displacement

Numerical simulations of unsteady flow problems with moving boundaries commonly require the use of geometric conservation law(GCL).However,in cases of unidirectional large mesh deformation,the cumulative error caused by the discrete procedure in GCL can significantly increase,and a direct consequence is that the calculated cell volume may become negative.To control the cumulative error,a new discrete GCL(D-GCL)is proposed.Unlike the original D-GCL,the proposed method uses the control volume analytically evaluated according to the grid motion at the time level n,instead of using the calculated value from the D-GCL itself.Error analysis indicates that the truncation error of the numerical scheme is guaranteed to be the same order as that obtained from the original D-GCL,while the accumulated error is greatly reduced.For validation,two challenging large deformation cases including a rotating circular cylinder case and a descending GAW-(1)two-element airfoil case are selected to be investigated.Good agreements are found between the calculated results and some other literature data,demonstrating the feasibility of the proposed D-GCL for unidirectional motions with large displacements.     

弧齿锥齿轮齿面拓扑修形及加工参数计算

为了能够实现对齿面啮合性能的灵活控制,针对弧齿锥齿轮小轮提出一种齿面拓扑修形方法,即借助二阶曲面对齿面偏差拓扑的近似表达,将齿面拓扑修形分解为5个方向:螺旋角修正、压力角修正、齿长曲率修正、齿廓曲率修正及齿面挠率修正,通过改变5个方向的修形系数对小轮齿面拓扑结构进行自由控制。在此基础上,建立齿面偏差与机床加工参数之间的修正数学模型,通过构建敏感性矩阵并采用最小二乘法求解,反求出获得修形齿面的小轮加工参数,以便指导加工。以一对弧齿锥齿轮副为例进行修形啮合分析,仿真结果表明:选取齿长曲率修形系数为0.0001,齿廓曲率修形系数为0.0005,齿面挠率修形系数为0.0003,对齿面进行拓扑修形后传动误差幅值为-25.60″,接触迹线倾斜角度变为54.7°,相比原始结果啮合性能得到改善。滚检接触区与理论仿真结果一致,验证了修形方法的有效性。      

L波段数字航空通信系统研究

随着全球航空运输的发展,空中交通管制与航空公司运控等航空业务对航空通信系统的数据传输速率、频谱利用率、航空通信网容量等性能提出了更高的要求。虽然现阶段基于甚高频的航空通信系统得到了迅速的发展,但仍受限于标准体制、技术壁垒等因素,难以满足持续增长的运行需求。L波段数字航空通信（L-band digital aeronautical communication system,L-DACS）数据链技术作为新一代航空通信系统的预选方案,是有效解决频谱资源饱和难题、满足高速率传输需求的有效途径。本文在总结L-DACS数据链技术发展现状的基础上,阐述了该通信系统现阶段的技术标准,分析了L-DACS发展所面临的挑战,提出了对应的发展建议,为面向航空宽带通信L-DACS的研究提供了参考与借鉴。     

低轨卫星通信系统地面核心网设计与仿真

文章针对无星际链路的低轨卫星通信系统，利用OPNET软件设计了低轨卫星通信系统在透明转发模式下的核心网构成，并进行了性能仿真。首先介绍核心网的构成、功能和拓扑，在此基础上实现了呼叫处理和切换的仿真，统计了呼叫时延、切换时延等性能指标，分析了仿真结果，为低轨道卫星通信系统的设计奠定了一定的参考价值。     

小型电磁辐射敏感度自动测试系统的设计

介绍电磁辐射敏感度自动测试系统组成、工作原理和设计方法，叙述了硬件配置、系统控制、数据采集处理等软件设计。其中较详细地介绍了光纤式场强数据采集部分的设计。     

我国税制结构的优化

随着经济的发展和税源结构的变化，税制结构的调整显得十分必要和紧迫，笔者分析了制约我国税制结构优化的因素、税制结构优化的标准，现行税制结构中存在的主要问题，并对优化我国税制结构的措施提出了具体看法。     

飞机起落架的TIG焊工艺

对用手工TIG焊方法代替目前航空部队采用的手工电弧焊(SMAW焊)修理飞机起落架进行了初步探讨,并经试验得出了TIG焊的最佳焊接工艺。     

驾驶员诱发振荡的抑制方法

对电传操纵系统驾驶员诱发振荡（ＰＩＯ）的现象进行了分析，指出了舵回路速率饱和是造成ＰＩＯ的主要原因，并有针对对给出了一种非常规的用于解决饱和非线性问题的程序控制方法。这种方法主要是通过舵回路反馈的状态信息来改变驾驶杆输入信号的放大系数，从而达到有效抑制ＰＩＯ的目的，同时用Ｈｕｒｗｉｔｚ稳定判据进行了机理分析，最后给出了仿真验证结果，证明该方法是简单而有效的。     

Development of an improved ground-based prototype of space plant-growing facility

Based on a formerly developed ground-based prototype of space plant-growing facility, the development of its improved prototype has been finished, so as to make its operating principle better adapt to the space microgravity environment. According to the developing experience of its first generation prototype and detailed demonstration and design of technique plan, its blueprint design and machining of related components, whole facility installment, debugging and trial operations were all done gradually. Its growing chamber contains a volume of about 0.5 m³ and a growing area of approximate 0.5 m²; the atmospheric environmental parameters in the growing chamber and water content in the growing media were controlled totally and effectively; lighting source is a combination of both red and blue light emitting diodes (LED). The following demonstrating results showed that the entire system design of the prototype is reasonable and its operating principle can nearly meet the requirements of space microgravity environment. Therefore, our plant-growing technique in space was advanced further, which laid an important foundation for next development of the space plant-growing facility and plant-cultivating experimental research in space microgravity condition.