结构非线性分叉失稳的扰动策略研究

将四种经典稳定判别准则中的初始缺陷准则应用于非线性有限元分析,提出了研究非线性分叉失稳扰动策略的初始微小缺陷法,分析了初始微小缺陷法的基本思路、分析步骤和优缺点。对单元铰接穹顶结构、Williams肘形刚架和K 6型凯威特单层网壳的非线性分叉失稳现象进行了深入研究,并对Williams肘形刚架进行了稳定性试验。结果表明,初始微小缺陷法是可行的和正确的,同时也揭示了初始微小缺陷是实际结构存在非线性分叉失稳的真正原因。     

Physiologic and metabolic responses of wheat seedlings to elevated and super-elevated carbon dioxide

The metabolic consequence of suboptimal (400 μmol mol⁻¹ or ppm), near-optimal (1500 ppm) and supra-optimal (10,000 ppm) atmospheric carbon dioxide concentrations [CO₂] was investigated in an attempt to reveal plausible underlying mechanisms for the differential physiological and developmental responses to increasing [CO₂]. Both non-targeted and targeted metabolite profiling by GC–MS and LC–MS were employed to examine primary and secondary metabolites in wheat (Triticum aestivum, cv Yocoro rojo) continuously exposed to these [CO₂] levels for 14, 21 and 28 days. Metabolite profile was altered by both [CO₂] and physiological age. In general, plants grown under high [CO₂] exhibited a metabolite profile characteristic of older plants under ambient CO₂. Elevated [CO₂] resulted in higher levels of phosphorylated sugar intermediates, though no clear trend in the content of reducing sugars was observed. Transient starch content was enhanced by increasing [CO₂] to a much greater extent at 10,000 ppm CO₂ than at 1500 ppm CO₂. The percentage increase of starch content resulting from CO₂ enrichment declined as plants develope. In contrast, elevated [CO₂] promoted the accumulation of secondary metabolites (flavonoids) progressively to a greater extent as plants became mature. Elevated [CO₂] to 1500 ppm induced a higher initial growth rate, while super-elevated [CO₂] appeared to negate such initial growth promotion. However, after 4 weeks, there was no difference in vegetative growth between 1500 and 10,000 ppm CO₂-grown plants, both elevated CO₂ levels resulted in an overall 25% increase in biomass over the control plants. More interestingly, elevated atmospheric [CO₂] reduced evapotranspiration rate (ET), but further increase to the supra-optimal level resulted in increased ET (a reversed trend), i.e. ET at 1500 ppm < ET at 10,000 ppm < ET at 400 ppm. The differential effect of elevated and super-elevated CO₂ on plants was further reflected in the nitrogen dynamics. These results provide the potential metabolic basis for the differential productivity and stomatal function of plants grown under elevated and super-elevated CO₂ levels.     

Minimum sliding mode error feedback control for fault tolerant small satellite attitude control

This paper proposes a new control strategy (which we call “minimum sliding mode error feedback control, MSMEFC”) for small satellite attitude control. As we know, the attitude control algorithm plays a significant role in the whole performance of the satellite, especially under the existence of uncertain disturbances from the space. Without loss of generality, the MSMEFC is presented based on the sliding mode theory. It is assumed that the equivalent control error is defined to offset the uncertain disturbances to improve the control performance. Hence, in order to estimate the optimal equivalent control error, a cost function is derived on the basis of the principle of minimum sliding mode error. Then, the equivalent control error wills feedback to the conventional sliding mode control to obtain the final MSMEFC. According to the theoretical analyzes, the sliding mode after the MSMEFC will approximate to the ideal sliding mode, resulting in enhancing the control performance. Moreover, an adaptive non-singular terminal sliding mode is employed to compare with the performance of MSMEFC. Several simulations are performed to verify the effectiveness of proposed MSMEFC in the presence of serious perturbations, even in some fault-tolerant scenarios.     

Introduction to global short message communication service of BeiDou-3 navigation satellite system

Short Message Communication (SMC) is a featured service of BeiDou Navigation Satellite System (BDS). After its successful deployment in 2003, Regional Short Message Communication (RSMC) service has been continuously serving China and its neighboring countries and regions, especially in life safety scenarios. In this paper, the architecture of the Global Short Message Communication (GSMC) system is proposed based on the medium earth orbit (MEO) constellation and the crosslinks of the global BeiDou navigation system (BDS-3). Three subtypes of GSMC service, i.e. positioning report, emergency search and rescue (SAR) and regular SMC are designed in accordance with the technical characteristic of integration of navigation and communication in BDS-3, which supports future wide applications of GSMC. The performance of the designed GSMC system is analyzed by numerical calculations. As BDS-3 was officially announced completion on July 31, 2020, GSMC has been providing initial service. First test results of the in orbit GSMC payloads are also presented in the paper to verify the designed capabilities. Preliminary results also show that the requirements of Global Maritime Distress and Safety System (GMDSS) can also be fulfilled.     

不同直径光滑圆管中黄原胶溶液流动减阻特性的实验研究

采用实验的方法,测试了黄原胶溶液在不同直径的光滑管道流动中的减阻特性和管径效应。其中变化参数为：（1）管道直径,共有3种管径,分别为5、10和20mm;（2）黄原胶溶液的浓度,变化范围为50~550ppm;（3）流速,用广义雷诺数（ReM）来表征,变化范围为0~50000。实验测量了不同参数下的管道压降Δp和体积流量Q,得到了黄原胶溶液浓度与减阻率的关系,以及ReM数对沿程阻力系数λ的影响,观测到黄原胶溶液减阻具有很明显的浓度效应,即随着溶液浓度的升高减阻率不断增大,直至达到最佳饱和减阻浓度,减阻率基本保持恒定。还观测到黄原胶溶液在不同管径中高低流速下表现出减阻类型的差异。     

基于Windows消息机制的MSC.Patran集成方法研究

为了解决航天器虚拟振动试验过程中的数据管理问题,提出了一种基于Windows消息机制的MSC.Patran软件集成方法,并设计了总体集成框架,针对其中的关键技术,如集成环境初始化、窗口动态控制等内容进行了详细论述。应用该方法和框架研制航天器虚拟振动试验系统,验证了其可行性。结果表明,该集成方法能够有效解决Patran与数据管理系统的数据集成共享问题。     

核心机派生间冷回热航空发动机热循环参数匹配研究

间冷回热航空发动机作为一种新概念动力技术,可满足未来民用航空发动机对成本控制、环境友好性等方面的要求.以成熟的核心机为基础,在常规热力循环基础上增加间冷过程和回热过程,匹配低压系统派生间冷回热涡扇发动机,进行热力循环参数选择与性能仿真分析.结果表明,派生的间冷回热航空发动机性能提升明显,与常规循环发动机相比,净推力增加...     

区域管制中Y2K问题的风险管理

Y2K将有可能造成管制区域中通信、导航、监视设备的全部或部分失效，为了保证飞行安全，必须进行风险管理。通过对假想空域中Y2K问题带来风险的分析，提出了几点控制风险的措施     

人工智能在电火花加工工艺知识库系统中的应用

]在分析电火花加工中工艺参数与加工性能之间关系的基本上，利用人工智能原理建立了电火花加工工艺知识库，并开发了相应的知识库系统，实现了电火花加工的工艺参数和加工性能之间的双向求解，