超高速干气密封扰流效应及抑扰机制

干气密封在高速时优异的动压性能使其应用范围从传统的压缩机、离心机等中高速设备逐渐扩大到航空发动机、（微型）燃气轮机等超高速设备中。基于实际超高速工况特点,对转速范围为10 000~120 000 r/min时的干气密封性能进行了系统性仿真计算,结果发现：在一定几何参数和工况参数下,类似于气浮轴承的微振动现象,干气密封会出现疑似受气体压力波动流影响的开启力、泄漏量与转速非正相关变化的扰流现象,尤其在高压、大膜厚、小槽深时的扰流效应愈加显著;在转速持续增大过程中,干气密封微尺度流场会出现二次拐点现象,且一次拐点发生转速与设计参数有关,而二次拐点发生转速基本约为90 000 r/min。同时结合导流织构的设计思路,进一步研究了超高速下干气密封槽底导流织构的驱动导流效应,结果表明：加设导流织构后,承载效果明显提高,拐点发生工况延后且压力波动区域被压缩。表明导流织构具有良好的抑制扰流、维持开启力与转速持续正相关的作用,在此基础上,进一步阐释了导流织构的抑扰机制,以期为突破干气密封在超高速工况下的应用壁垒提供新思路。     

基于STM32F429的全向运动平台的运动控制

全向运动平台系统是可以实现人体在各个方位行走的2D运动平台。针对实现人体在全向运动平台稳定行走的运动控制,采用加入观测器的一阶控制算法对平台运动控制进行探究。先通过MATLAB软件进行算法的仿真,验证方法的可行性;再通过现场测试,验证控制算法的有效性。最终试验表明,加入观测器的一阶控制算法可对全向运动平台实现有效的运动控制。此运动控制策略的探究为全向运动平台的运动控制提供了一种可行的控制思路和方案。     

一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

Dynamics and de-spin control of massive target by single tethered space tug

This paper investigates the dynamics and de-spin control of a massive target by a single tethered space tug in the post-capture phase. The dynamic model of the tethered system is derived and simplified to a dimensionless form. Further, a decoupled PD controller is proposed, and the local stability of the controller is analyzed by linearization technique. Parametric studies of the dynamics and de-spin control of a massive target are conducted to characterize the dynamic process of de-spin with the proposed control law. It is shown that the massive target can be de-span by a single and small space tug with limited thrust within finite time. The thrust tangent with the tether de-spins the target while the thrust normal to the tether prevents the tether from winding up the target. The tether length has a positive contribution to the de-spin of a target. The longer tether leads to a faster de-spin process.     

Containment of soft wall casing wrapped with Kevlar fabric

Aramid fabrics have been commonly used in the civil turbofan engine fan blade containment system for its excellent performance. To investigate the behavior and capability of soft wall containment casing, a series of fan blade released tests were conducted on the high-speed spin tester.The soft wall casing was fabricated by wrapping multiple layers of Kevlar49 plain woven fabric around a thin steel ring. Casings with different inner metal ring and outer fabric layers number were compared. The method of using the explicit dynamic software LS-DYNA to establish the finite element analysis model for the quantitative analysis of the containment process was developed and conducted. The simulation results are in good agreement with the test results. It is shown that the containment process of the soft wall casing can be divided into three impact stages. The casing with low-stiffness inner metal ring will get severe overall deformation and lose the structural integrity when it suffers the blade impact. Kevlar fabric layers will appear large bulge on outside surface and absorb the most impact dynamic energy of the high speed released fan blade. By summing up the results of the test and simulation, an empirical critical equation was derived to describe the relationship between the released blade dynamic energy and the Kevlar fabric thickness.     

摆线桨非定常动态失速的三维效应

对摆线桨三维全尺寸模型进行了非定常数值模拟。验证了两种嵌套网格方法的可靠性与适用性,针对二维/三维情况下摆线桨非定常涡流动特性及诱导分离特性开展了数值分析,重点研究了展向气动力随方位角的分布与全局流场的诱导速度分布,并分析了尾迹捕捉精度与涡量耗散特征。结果表明:受摆线桨切向速度、展向诱导速度等三维效应影响,两种计算结果的瞬态气动力极值差值达到44%。三维动态失速涡的产生、脱落与再附明显弱于二维翼型情况,这对于摆线桨非定常气动特性有较大影响。      

烧蚀后C-SiC复合材料隔离段内激波串长度预测

为了研究畸变气流影响下烧蚀后的C-SiC复合材料隔离段内激波串长度预测问题,设计了能够模拟进气道喉道流场畸变的隔离段直连台,并开展了马赫数2.5和3.5来流的两种不同烧蚀程度的C-SiC复合材料隔离段直连实验,获得了有效的纹影和压力数据,结合实验和理论分析,采用无量纲不平度hs/Dhy来表征烧蚀后C-SiC隔离段内壁面严重不规则粗糙特征,尝试在Waltrup公式中增加包含无量纲不平度的因子(1+4hs/Dhy),以此形成新的公式来预测烧蚀后C-SiC隔离段内激波串长度,预测精度较原来公式大幅提高,按照10%的误差带分析,修正后的Waltrup公式预测精度提高了33.3%。     

Six sigma robust design optimization for thermal protection system of hypersonic vehicles based on successive response surface method

Lightweight design is important for the Thermal Protection System(TPS) of hypersonic vehicles in that it protects the inner structure from severe heating environment. However, due to the existence of uncertainties in material properties and geometry, it is imperative to incorporate uncertainty analysis into the design optimization to obtain reliable results. In this paper, a six sigma robust design optimization based on Successive Response Surface Method(SRSM) is established for the TPS to improve the reliability and robustness with considering the uncertainties. The uncertain parameters related to material properties and thicknesses of insulation layers are considered and characterized by random variables following normal distributions. By employing SRSM, the values of objective function and constraints are approximated by the response surfaces to reduce computational cost. The optimization is an iterative process with response surfaces updating to find the true optimal solution. The optimization of the nose cone of hypersonic vehicle cabin is provided as an example to illustrate the feasibility and effectiveness of the proposed method.     

利用航天器分舱段振动试验数据获取整器响应的方法

未来大型组合体航天器振动试验可能难以在现有设备上进行,需要进行分舱考核。文章针对此问题开展了利用分舱段振动试验获取整器响应的方法研究。提出的方法为:根据不同界面下模态的映射关系,利用单舱段的振动试验数据辨识出舱段的两端固支模态;采用模态综合技术计算出整器组合体模态参数,拟合出结构的加速度响应传递函数;结合整器的加速度试验条件可以给出整器的试验响应曲线。仿真验证结果表明该方法合理可行,具有工程应用价值。     

用于BVI噪声试验的新型涡发生器设计与分析

针对直升机特有的旋翼桨/涡干扰(Blade vortex interaction,BVI)噪声计算精度低且试验数据缺乏问题,也为了开展旋翼气动噪声特性分离方法的验证试验研究,本文设计了一种能够用于BVI噪声试验的新型多段翼型组合式涡发生器。首先通过CATIA软件建立涡发生器出口端翼型段在不同迎角下的试验模型,再使用FLUENT软件建立涡发生器的流场仿真计算模型,比较分析了不同翼型段迎角下的涡流流场。随后用粒子图像测速法(Particle image velocimetry,PIV)技术系统测量了不同翼型段迎角、距离涡发生器出口端的长度及流速等参数变化下的涡流流场,对不同试验状态下的涡核、涡强等参数进行了对比分析。针对涡量偏弱的缺点,对传统单级涡发生器进行了改进,设计研发了双级涡发生段。试验证明其能产生更强且稳定的涡,为BVI噪声试验提供了模拟的桨尖涡,试验结果表明了涡发生器的有效性。