DSP的数学原理及在实时系统的应用

制造系统里所用的微处理器中，单片机只能做逻辑处理和简单数学计算，而数字信号处理器（DSP）可进行相当复杂的数学处理。本文概述DSP的数学原理及其技术特点，介绍了基于DSP智能控制器在制造业中实时测控系统的应用实例。     

模拟月壤研制的初步设想

模拟月壤是月球样品的地球化学复制品，作者总结世界上已有的5种模拟月壤JSC-1，MLS．1，MLS-2，MKS-1和FJS-1的研制过程、方法与基本理化性质，认为系列化模拟月壤研制对中国首次月球探测有重要意义，在此基础上，作者提出系列化模拟月壤研制的基本思路．     

控制系统通用综合测试系统组建研究

在分析系统需求和基本功能的基础上 ,采用VXI总线技术、远程测控技术和测试应用程序自动生成等关键技术 ,按照综合测试的总体要求进行系统集成 ,组建控制系统通用综合测试系统 ,包括系统硬件和软件方案 ,对系统的硬件结构方案、模件选型以及软件流程、组成和作用进行了详细讨论。     

线阵CCD平场校正及FPGA实现的研究

为了消除由于照明光源的非均匀性、镜头渐晕及CCD传感器噪声对图像质量造成的不良影响,首先从理论上分析了线阵CCD固定模式噪声和像素光电响应非均匀性的数学模型和产生的原因;对像素光电响应非均匀性这一主要影响因素,根据其光电响应模型提出了CCD像素光电响应非均匀性的两点校正方法,即求解出各个像素光电响应不均匀性的校正因子和暗偏置量系数,进而用以计算各个像素的校正量,实现逐点校正;针对校正算法大数据量、实时计算的要求,设计了基于现场可编程逻辑门阵列FPGA快速实现校正算法的硬件处理结构。最后,通过仿真和实验表明,两点校正方法可以有效地减小CCD像素光电响应不均匀性的图像噪声,提高图像质量,以便做后续精确处理。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.     

PBT弹性体力学性能及低温脆性研究

采用一步法制备了热固性3,3-双(叠氮甲基)环氧丁烷-四氢呋喃共聚醚(PBT)弹性体,并对其氢键结构、应力-应变关系和动态力学性能及低温脆性进行了研究。结果表明,合成的PBT弹性体拉伸强度和断裂伸长率在DEG羟基含量为35%、R=0.97时,可达2.51 MPa和1 274%,玻璃化温度为-34.5℃。高DEG含量的PBT弹性体脆化参数较低,与常温力学性能变化规律相反。因此,引入低温脆化参数,对PBT弹性体的性能优化具有积极意义。     

微磁强计弱磁处理芯片设计与实现

为适应微纳卫星平台的应用需求、实现磁强计的微型化,针对巨磁阻抗(GMI)效应微磁强计的研制需求设计并研制了弱磁信号处理芯片.在分析GMI微磁强计构造的基础上,针对单机(微)小型化提出了弱磁信号处理电路芯片化的方案;结合空间应用特点,设计并实现了基于SOI CMOS工艺的弱磁信号处理芯片.实测结果表明:基于所研制的弱磁信号处理芯片不仅实现了磁强计的微型化、集成化,而且具有良好的弱磁测量性能.     

叶片反扭对跨声速大涵道比风扇性能的影响

使用基于流固耦合算法的叶片反扭程序,考虑了非定常气动力对叶片变形的非线性作用,研究了叶片反扭对跨声速大涵道比风扇性能的影响.以冷态叶型为起点,先计算离心力作用下的叶片变形,在此基础上使用流固耦合程序获得非定常气动力作用下的变形.考察了3个转速下叶片的动态变形对大涵道比风扇气动性能的影响.结果表明:在跨声速工况下,叶片表面激波位置的变化对叶片反扭角有很大作用,在考察的转速范围内,堵塞点使用设计叶型计算的流量大于动态叶型下的流量,数值达7%,将导致发动机起飞推力小于预测值.结果表明在大涵道比风扇设计阶段,预测气动性能使用准确叶型的重要性.