吊挂系统对波瓣混合排气系统气动热力性能影响

为了明确短舱中吊挂系统的堵塞效应对波瓣混合排气系统气动热力性能的影响,采用数值模拟的方法对包含吊挂的混合排气系统进行了定量研究。研究结果表明,受吊挂系统的影响,在波瓣混合排气系统混合段内,存在着一大尺度的回流区,其作用范围随吊挂长度的增加而增加。在性能参数方面,与未考虑吊挂系统时相比,考虑吊挂之后,虽然混合排气系统出口处热混合效率以及推力系数下降很小,最大降幅仅分别为0.017和0.01,但总压恢复系数却显著下降,最大降幅达到了0.03。此外,随着吊挂系统长度的变化,排气系统出口处的热混合效率、总压恢复系数以及推力系数变化幅度小于0.01,变化很小。     

Optimization of beamforming and path planning for UAV-assisted wireless relay networks

Recently, unmanned aerial vehicles （UAVs） acting as relay platforms have attracted considerable attention due to the advantages of extending coverage and improving connectivity for long-range communications. Specifically, in the scenario where the access point （AP） is mobile, a UAV needs to find an efficient path to guarantee the connectivity of the relay link. Motivated by this fact, this paper proposes an optimal design for beamforming （BF） and UAV path planning. First of all, we study a dual-hop amplify-and-forward （AF） wireless relay network, in which a UAV is used as relay between a mobile AP and a fixed base station （BS）. In the network, both of the AP and the BS are equipped with multiple antennas, whereas the UAV has a single antenna. Then, we obtain the output signal~to-noise ratio （SNR） of the dual-hop relay network. Based on the criterion of maximizing the output SNR, we develop an optimal design to obtain the solution of the optimal BF weight vector and the UAV heading angle. Next, we derive the closed-form outage probability （OP） expression to investigate the performance of the dual-hop relay network conveniently. Finally, computer simulations show that the proposed approach can obtain nearly optimal flying path and OP performance, indicating the effectiveness of the proposed algorithm. Furthermore, we find that increasing the antenna number at the BS or the maximal heading angle can significantly improve the performance of the considered relay network.     

大型回流边界层风洞的气动与结构设计

大型边界层风洞是开展风工程研究的必备装备。以浙江大学ZD-1边界层风洞的研制为背景,详细介绍了大型回流边界层风洞气动设计和立式结构设计中的关键问题,在风洞气动设计时采用了收缩比为4∶1的单回路单试验段气动轮廓,在试验段中设置了0．22°的当量扩散角,对拐角导流片外形作了特殊处理,并采用钢结构与混凝土结构相结合的立式结构。流场校验结果表明,大型回流边界层风洞的气动与结构设计能满足设计要求,某些指标甚至达到航空风洞的标准,在试验段中设置扩散角有利于降低轴向静压梯度,立式结构设计对提高试验段气流的水平均匀性有一定的作用,可为今后类似风洞的研制提供参考。     

POSS 催化剂改性氰酸酯复合材料的性能

通过POSS 催化剂改性氰酸酯树脂,并采用热熔法排布制备了碳纤维/ 中温固化氰酸酯预浸料, 验证了改性氰酸酯的工艺性。同时考察了氰酸酯树脂及其复合材料的性能。结果表明, POSS 催化剂的加入, 降低了氰酸酯的固化温度,同时其使用温度、室温及-18℃的储存性能和复合材料力学性能与改性前相当。     

基于比例导引角度线性化的无人机避障研究

基于无人机与障碍物之间的几何关系,在极坐标系下建立了无人机与障碍物之间的运动学方程,通过引入基于角度线性化的比例导引律,使无人机能够顺利避开障碍物。引入的基于角度线性化的比例导引律是关于无人机相对速度航向角与避障点视线角的函数,由比例函数及偏差函数组成。为解决初始时刻相对速度航向角不满足引入导引律的问题,在调节函数中加入了指数项。通过稳定性证明,得到了满足要求的导引律参数取值范围。最后对设计的避障算法进行了仿真,仿真结果验证了算法的有效性。     

基于A320飞机横航向控制律架构的LQ设计

空客A320飞机横航向控制律采用特征结构配置方法计算闭环增益,实现了期望特征值的配置及横航向关键参数之间的解耦。基于A320横航向控制律架构,提出使用线性二次型(Linear Quadratic,简称LQ)方法,对闭环增益进行重新设计。首先根据期望的特征值引入关键参数的频域整形环节,而后通过调整二次型性能指标加权矩阵实现期望特征值的逼近及关键参数之间的解耦,并求得闭环反馈增益,最后在特征结构、稳定裕度和横航向解耦效果方面与空客设计结果作了对比分析。仿真结果表明,LQ设计可获得与特征结构配置设计相近的结果,即得到接近期望值的特征值,并实现关键变量的解耦,同时保证了闭环稳定裕度。     

BAMO-THF叠氮型热塑性聚氨酯弹性体的合成与表征

为了研究叠氮型热塑性含能粘合剂的合成方法及反应条件对其力学性能的影响,通过熔融预聚二步法合成了以3,3-双(叠氮甲基)环氧丁烷-四氢呋喃共聚醚(BAMO-THF)为软段、异佛尔酮二异氰酸酯(IPDI)及1,4-丁二醇(BDO)为硬段的叠氮型热塑性聚氨酯弹性体(ATPE)。采用傅立叶变换红外光谱(FTIR)对所制备的ATPE的结构进行了表征。通过二正丁胺滴定法确定了最佳的预聚反应时间。研究比较了固化参数R和硬段含量对ATPE力学性能的影响。利用差示扫描量热(DSC)测定了ATPE的玻璃化转变温度,计算了硬段溶于软段的百分数。研究结果表明,所合成的ATPE具有典型的叠氮聚醚聚氨酯特征;确定了预聚反应时间为2 h;当R=1.02时,ATPE的拉伸强度最大,约为4 MPa;硬段含量为40%的ATPE的拉伸强度最大,为3.54 MPa;当硬段含量超过40%以后,硬段溶入软段的百分数小于10%,ATPE体现出良好的微相分离。     

Statistical study of interplanetary condition effect on geomagnetic storms: 2. Variations of parameters

We investigate the behavior of mean values of the solar wind’s and interplanetary magnetic field’s (IMF) parameters and their absolute and relative variations during the magnetic storms generated by various types of the solar wind. In this paper, which is a continuation of paper [1], we, on the basis of the OMNI data archive for the period of 1976–2000, have analyzed 798 geomagnetic storms with D _st ≤ −50 nT and their interplanetary sources: corotating interaction regions CIR, compression regions Sheath before the interplanetary CMEs; magnetic clouds MC; “Pistons” Ejecta, and an uncertain type of a source. For the analysis the double superposed epoch analysis method was used, in which the instants of the magnetic storm onset and the minimum of the D _st index were taken as reference times. It is shown that the set of interplanetary sources of magnetic storms can be sub-divided into two basic groups according to their slowly and fast varying characteristics: (1) ICME (MC and Ejecta) and (2) CIR and Sheath. The mean values, the absolute and relative variations in MC and Ejecta for all parameters appeared to be either mean or lower than the mean value (the mean values of the electric field E _y and of the B _z component of IMF are higher in absolute value), while in CIR and Sheath they are higher than the mean value. High values of the relative density variation sN/〈N〉 are observed in MC. At the same time, the high values for relative variations of the velocity, B _z component, and IMF magnitude are observed in Sheath and CIR. No noticeable distinctions in the relationships between considered parameters for moderate and strong magnetic storms were observed.     

Detonation engine fed by acetylene–oxygen mixture

The advantages of a constant volume combustion cycle as compared to constant pressure combustion in terms of thermodynamic efficiency has focused the search for advanced propulsion on detonation engines. Detonation of acetylene mixed with oxygen in various proportions is studied using mathematical modeling. Simplified kinetics of acetylene burning includes 11 reactions with 9 components. Deflagration to detonation transition (DDT) is obtained in a cylindrical tube with a section of obstacles modeling a Shchelkin spiral; the DDT takes place in this section for a wide range of initial mixture compositions. A modified ka-omega turbulence model is used to simulate flame acceleration in the Shchelkin spiral section of the system. The results of numerical simulations were compared with experiments, which had been performed in the same size detonation chamber and turbulent spiral ring section, and with theoretical data on the Chapman–Jouguet detonation parameters.     

工艺参数对CVD制备热解碳界面层厚度的影响

以甲烷(CH4)为碳源先驱体,以三维针刺碳纤维预制体为沉积基体,研究了化学气相沉积(chemical vapor deposition,CVD)工艺过程中沉积时间、沉积压力以及预制体厚度对热解碳界面层沉积厚度的影响,并在此基础上优化了在碳纤维表面制备合适厚度的热解碳界面层所需的CVD工艺参数。结果表明,针对现有反应腔体,5 mm厚碳纤维预制体试样,采用1 000℃的沉积温度,CH4流速500 ml/min,沉积时间10 h,沉积压力5 kPa,可在预制体内外碳纤维表面沉积得到厚度合适的热解碳界面层;当碳纤维预制体厚度增至10 mm,则沉积时间应延长至15 h,压力维持不变,可沉积得到合适厚度的界面层。