Constant thrust-V-bar departure under the thruster failure

In this paper, a field-of-view constrained guidance algorithm for -V-bar constant thrust departure under thruster failure is investigated. First of all, the relative position parameters of the chaser are obtained by using the vision measurement and the target departure manoeuvres positions are calculated through the isochronous interpolation method. Then, a new switching control law under constant thrust is designed for the departure manoeuvres. The switching control law is obtained based on the acceleration sequences and the on time of thrusters which can be computed by the time series analysis method. The perturbations and fuel consumptions are addressed during the computation of the on time of thrusters. With the switching control law, the constant thrust-V-bar departure under the thruster failure in the x-axis is carried out by using coupling effects.On the basis of the toolbox of matlab, practical examples for simulation and application are given. The half cone angle of the cone-shaped field-of-view of the target spacecraft is α = 30°, the simulation results show that the proposed guidance algorithm can well satisfy the conditions for the constraints and can make sure the chaser departures from the target spacecraft safely.     

Constant thrust fuel-optimal control for spacecraft rendezvous

In this paper, constant thrust rendezvous is studied and the optimal rendezvous time is calculated by using continuous genetic algorithm. Firstly, the relative position parameters of the target spacecraft are obtained by using the vision measurement and the target maneuver positions are calculated through the isochronous interpolation method. Then, the results of the calculation of constant thrust rendezvous is founded by processing with multivariate linear regression method. Next, a new switching control law is designed based on the thrust acceleration sequence and the on time of thrusters which can be computed by the time series analysis method. The perturbations and fuel consumptions are addressed during the computation of the on time of thrusters.     

基于非概率凸模型可靠性的结构优化设计

考虑到结构系统参数的不确定性,基于提出的非概率凸模型可靠性指标的新定义,研究了在非概率凸模型可靠性约束下,结构优化设计的数学模型和求解方法.该方法通过超椭球域界定不确定参量,将结构基本不确定变量安全域的超体积与其可行域的超椭球总体积之比作为结构非概率可靠性的度量.并赋值可靠度作为约束条件,利用乘子法和阻尼牛顿法对结构的优化问题进行迭代求解,算法稳定,迭代速度快.数值算例验证了所提出方法的正确性.     

Phase Residual Estimations for PCVs of Spaceborne GPS Receiver Antenna and Their Impacts on Precise Orbit Determination of GRACE Satellites

In-flight phase center systematic errors of global positioning system(GPS) receiver antenna are the main restriction for improving the precision of precise orbit determination using dual-frequency GPS.Residual approach is one of the valid methods for in-flight calibration of GPS receiver antenna phase center variations(PCVs) from ground calibration.In this paper,followed by the correction model of spaceborne GPS receiver antenna phase center,ionosphere-free PCVs can be directly estimated by ionosphere-free carrier phase post-fit residuals of reduced dynamic orbit determination.By the data processing of gravity recovery and climate experiment(GRACE) satellites,the following conclusions are drawn.Firstly,the distributions of ionosphere-free carrier phase post-fit residuals from different periods have the similar systematic characteristics.Secondly,simulations show that the influence of phase residual estimations for ionosphere-free PCVs on orbit determination can reach the centimeter level.Finally,it is shown by in-flight data processing that phase residual estimations of current period could not only be used for the calibration for GPS receiver antenna phase center of foretime and current period,but also be used for the forecast of ionosphere-free PCVs in future period,and the accuracy of orbit determination can be well improved.     

航天元器件关键工艺的统计过程控制方法

文章以统计过程控制（SPC）中的均值—标准差（X—R）控制图理论方法为基础,以宇航元器件关键工序中的集成电路键合拉力强度为研究对象,提出宇航元器件关键工序进行SPC的必要性,并提出以（X—R）控制图作为质量工具对宇航元器件关键工艺进行质量监控的方法,计算出该关键工艺的过程能力指数。     

航空发动机多变量变增益控制器设计及仿真

针对航空发动机全包线工作下的多变量变增益控制器设计问题,给出了一种改进的埃德蒙德算法（以下简称KQ算法）并进行了仿真应用。首先,阐明了多变量KQ算法的控制原理与优化算法,进而通过闭环期望函数选择、控制器结构选择以及控制器参数优化进行了KQ控制器设计,并针对所设计的KQ控制器,给出了稳定性证明和系统奇异值分析。分析表明所设计KQ控制器能够使系统闭环稳定,且具有满意的低频指令跟踪、干扰抑制能力、传感器噪声的抑制、高频未建模动态的鲁棒稳定性和低频发动机建模误差不敏感等性能,满足发动机控制要求。其次,通过调度变量选择、设计点KQ控制器设计以及采用插值方法的非设计点KQ控制器设计等过程实现某型涡扇发动机的多变量KQ变增益控制器设计研究,并进行仿真验证。仿真结果表明,设计点条件下,当涡轮后温度和增压比参考输入均为阶跃信号时,其被控参数响应速度很快,且上升时间均小于1 s,耦合影响小于6%,设计点KQ控制器满足控制要求;非设计点条件下,利用插值方法建立的KQ变增益控制器具有较好的性能,能够实现该型涡扇发动机全包线控制性能要求。      

基于相位差测量的脉冲星时间相对导航方法

针对传统脉冲星导航方法在相位估计时依赖脉冲星信号轮廓,存在整周模糊及不确定星历参数引起的系统共模误差问题,提出基于相位差测量的脉冲星时间相对导航方法。该方法通过对脉冲星光子到达时间序列进行相位估计,以相邻时刻的相位差作为观测量,建立航天器位置增量与相位差的关系,采用广义卡尔曼滤波器处理系统噪声相关问题进行导航,可有效减小系统误差,实现脉冲星导航的应用。通过对导航系统初始定位方法、可观性分析,及基于罗西X射线时变探测器（RXTE）观测的Crab脉冲星的在轨实测数据试验分析,证明了该方法的自主性与可行性。最后,对基于相位差测量的脉冲星时间相对导航系统进行导航滤波仿真,试验结果表明,导航系统完全可观,噪声不累积,位置估计精度可满足实际应用。     

基于时域有限差分的渐变温信号传输模型

建立了一种基于时域有限差分(FDTD)的渐变温信号传输模型,利用迭代求解实现了传输导线在不同时间受不同温度影响的仿真分析.结果表明:测试信号的时域平均电压幅值随温度的升高而逐渐衰减,在573K时,电压幅值仅为303K时的90%左右,衰减幅度近10%.设计了一种渐变温环境下的振动测试试验,所得的输出信号的自功率谱峰值和时域平均电压幅值均随温度升高而减少,试验结果与仿真分析结果一致.此研究结果有助于提高振动测试的准确性.      

空间绳系组合体的继电型控制离轨策略

为了使空间绳系组合体更好地完成空间碎片清理任务,提出一种更接近工程实际应用的继电型推力（Bang-Bang）离轨控制策略。利用带有差动间隙的Bang-Bang控制策略,实现绳系组合体切向的继电式推力加速;设计了一种全新的被动式卷扬机构,以避免在使用继电式推力离轨的过程中多次开关发动机对绳系组合体带来的负面影响;针对径向推力设计了输入受限的滑模控制器,且最终控制指令同样以继电式推力形式实现,抑制了离轨过程中绳系组合体的面内摆动。数值仿真结果显示,继电型推力能够实现与连续推力近似的效果,能够将绳系组合体的摆动角度抑制在一个较小的范围内;整个离轨控制策略能够使得空间绳系组合体在保持姿态稳定的前提下将空间碎片拖曳到坟墓轨道。     

整体叶盘电解加工阴极修正方法与试验

电解加工是航空发动机整体叶盘制造的主要技术之一,阴极修正是该加工技术的重要环节。为了提升阴极修正精度,提出了恒采样点空间法向修正方法。该方法将阴极型面设计、加工误差分析、工具阴极修正统一至阳极采样点空间法向的一维坐标系中,将复杂的三维曲面修正简化为离散的一维修正,消除了加工误差与修正量的错位。以某整体叶盘为例,在自行研制的整体叶盘型面电解加工机床上开展工具阴极修正试验,采用三坐标测量机对修正前后的加工样件进行检测,经过一次修正,叶片电解加工精度由0.25mm提高至0.04mm,试验结果表明该阴极修正方法合理有效,具有较强的可行性。