柔性扑翼气动结构耦合特性数值研究

微型扑翼体积小、重量轻,其柔性变形对气动特性有显著的影响。通过求解雷诺平均N-S方程(ReynoldsAveraged Navier-Stokes,RANS)和结构动力学方程,对微型柔性扑翼飞行器的气动结构耦合特性进行了数值模拟研究。针对微型扑翼的大幅运动,发展了适用于扑翼的气动结构耦合数值计算方法,研究了微型扑翼的气动结构耦合特性。通过求解雷诺平均Navier-Stokes(RANS)方程得到微型扑翼的非定常气动特性;利用哈密顿原理(Hamilton Principle)推导了扑翼的结构动力学方程,采用结构有限元方法对该动力学方程进行离散并求解,得到扑翼的动态结构特性;采用松耦合方法进行迭代。计算结果与风洞实验结果相比吻合良好,验证了所发展方法的有效性。在此基础上研究了惯性力和关键运动参数对柔性扑翼气动及结构特性的影响规律,有助于比较详细、全面地了解微型扑翼的气动机理,为柔性扑翼的设计提供了参考依据。     

基于功能危险性评估的民用飞机驾驶舱门设计探讨

FAA分别于2002年和2008年颁布25-106及25-127修正案,增加驾驶舱门安保事项以提高驾驶舱的安全水平。修正案要求加固驾驶舱门,驾驶舱门必须设计成可以阻止未被授权人员进入驾驶舱并且阻碍危险物体射入以保证机组人员的安全。驾驶舱门必须能检测驾驶舱失压并可以释放门或者卸压板平衡压力差,还应有措施使飞机机组成员在该舱门卡住的情况下能直接从驾驶舱进入客舱。因此,在驾驶舱门上设有一个可以快速释放的紧急出口。根据飞机驾驶舱门结构及功能的主要特点,对驾驶舱门功能故障进行探讨,同时对功能故障引发的危险性等级进行划分,以确定安全指标,进而辅助驾驶舱门设计工作。     

吸气式高超声速飞行器内外流同时测力试验

为研究吸气式高超声速飞行器新型测力试验技术的可行性,在马赫数Ma=6、高度H=27km模拟飞行环境下开展了风洞试验。以轴对称吸气式高超声速飞行器无舵翼简化构型为研究对象,通过合理的试验系统设计解决内外流解耦关键技术,采用两个环式六分量天平在同一车次上测量模型内外流气动力载荷。试验结果表明:内外流气动力天平测量数据和全模气动力数据准确反映了内外流解耦、内外流窜流、进气道起动/不起动以及溢流影响等物理现象;从物理上实现了内外流解耦;内流气动力对全机气动性能贡献大;内外流解耦、进气道起动时,气动力数据准确、重复性好;窜流产生的传力属于内力。试验证明,同时测力试验技术可行,为解决内外流气动数据源于不同试验所致的不确定性问题提供了有效手段。     

亚声速进气道设计敏感参数仿真分析

对不同气动布局的两种亚声速进气道建模,并针对两种进气道的敏感参数进行分析。通过对背部双发布局飞机进气道的隔道高度和喉道设计马赫数参数的研究可知,隔道高度增大或者喉道设计马赫数减小,使得进气道出口总压恢复系数增大,增量约0.5%。而对背部单发复杂形状进口(M型进口)布局飞机进气道的喉道形状研究显示,喉道形状越接近进口形状,进气道性能越好,较其他喉道形状进气道,M型喉道进气道出口总压恢复系数最高,最大增量约为1.5%。     

无网格法耦合RNG k-ε湍流模型在亚、跨声速翼型黏性绕流中的数值模拟

基于移动最小二乘无网格方法,耦合RNG(Re-Normalisation Group)k-ε湍流模型求解雷诺平均Navier-Stokes方程。采用AUSM(Advection Upstream Splitting Method)+-up迎风格式求解数值通量,应用在高度各向异性点云结构中取得良好结果的点云重构技术结合移动最小二乘法拟合空间导数,并用三阶SSP(Strong Stability Preserving)型Runge-Kutta显式时间推进格式求解离散后的控制方程。在此基础之上,实现了对NACA0012、RAE2822翼型亚、跨声速黏性绕流的数值模拟,给出了翼型表面压力系数分布曲线、不同位置处的平均速度剖面、马赫数等值线等计算结果,并与实验值及相关文献数值模拟结果进行比较,结果吻合较好。表明所发展的结合点云重构技术的无网格方法耦合RNGk-ε湍流模型能够成功模拟翼型亚、跨声速黏性绕流,验证了所提算法的有效性,并拓展了无网格方法求解湍流流动的途径。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

二元双喉道射流推力矢量喷管流动参数影响的数值研究

采用数值模拟方法研究了不同流动参数对二元双喉道射流推力矢量喷管(Dual-throat fluidic Thrust-vectoring Nozzle,DTN)内流特性和推力矢量控制效果的影响。结果表明,DTN在非推力矢量情况下,NPR在3~4范围时,推力系数较大,达到0.968,而流量系数较小,仅为0.93;NPR再增大,推力系数迅速下降。在推力矢量情况下,落压比一定时,随着次流流量比的增加,推力矢量角增加,而流量系数、推力系数、推力矢量效率减小;次流流量比一定时,随着落压比的增加,推力矢量角减小,系统推力系数先增加后减小,流量系数略微增加。     

民用飞机壁板蒙皮及长桁布置结构优化设计

机身壁板是飞机结构设计的重要承载组件,轻量化、高效率、共通性设计及优化是民机设计关注的重点。首先提出一种耦合ABAQUS的Buckle分析及ISIGHT优化的设计方法,利用自编子程序获取ABAQUS屈曲特征值,将特征值输入ISIGHT中计算临界屈曲载荷,同步更新变量参数及ABAQUS文件并提交计算,迭代分析直至优化流程结束。采用上述方法考虑轴向压缩载荷情况,以壁板整体重量最小为优化目标,疲劳应力值为约束条件,对单曲度金属机身壁板的蒙皮厚度,长桁数量及长桁截面厚度等几何参数进行优化。在满足壁板结构承载能力及总重量最小条件下,综合考虑结构载重比,临界应力及壁板加筋比,对比分析出一组最优参数,并与工程算法结果对比吻合程度较好,两者相对误差为3.73%。该优化思路实现FEA平台与优化工作一体化,可用于复合材料壁板设计及结构件减重优化工作,一定程度上可缩短零组件设计周期。     

新型压电激励器作用力模拟技术研究

研究轻型结构、直升机旋翼结构和复合材料结构等的颤振飞行试验激励问题具有重要意义。提出以弯矩模拟压电粗纤维复合材料(MFC)激励器的作用力,从而解决MFC仿真建模问题。首先借助机翼有限元模型,建立带有压电激励器的机翼结构动力学仿真模型;然后以压电激励器地面激励试验结果为基础,通过修正仿真模型中压电作用弯矩的大小,实现仿真试验结果与地面试验结果的拟合,最终得出非线性压电激励器作用力;最后通过另一组地面试验数据验证了该作用力的大小,并将该作用力模拟技术应用于不同试验中。本文的研究结果可为后续以该激励器作为激励作动器或控制作动器的试验提供有益参考。