多导弹齐射攻击协同制导(英文)

Cooperative guidance problems of multiple missiles are considered in this article. A cooperative guidance scheme, where coordination algorithms and local guidance laws are combined together, is proposed. This scheme actually builds up a hierarchical cooperative guidance architecture, which may provide a general solution to the multimissile cooperative guidance problems. In the case of salvo attacks which require missiles to hit the target simultaneously, both centralized and distributed coordination algorithms are derived based on the impact-time-control guidance （ITCG） law. Numerical simulations are performed to demonstrate the effectiveness of the proposed approaches.     

Erosion of a Polyimide Material Exposed to Simulated Atomic Oxygen Environment

Oxygen plasma source generated by thermal cathode filament discharge has been used to study the erosion process of polyimide (PI) materials in atomic oxygen (AO) environment, and their mass loss, surface morphology and surface chemical compositions have been examined by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) after exposure to incremental AO flux. The data indicate that the physical adsorption of AO at the samples' surface results in the increase of oxygen concentration when polyimide is exposed to AO flux. Then selective chemical reactions of groups of polyimide materials with AO yield volatile organic compounds, sample mass loss is on linear increase and carpet-like surface morphology forms. In the initial exposure to AO, the reaction occurs mainly between AO and carbon in specific location of aromatic ring, then the reaction rate of C=O groups gradually increases. After AO exposure, the oxygen concentration increases while nitrogen and carbon concentration decreases. Reaction rate of groups containing nitrogen is slower compared with carbon and oxygen.     

Fe—10Ni—14Co钢标准状态的组织研究

用透射电子显微镜重点研究了Ｆｅ－１０Ｎｉ－１４Ｃｏ钢的标准处理状态（８３０℃风冷＋—７３℃＋５１０℃Ｓｈ）的微观组织结构。５１０℃回火不同时间，由于Ｍ２Ｃ的析出状态发生变化，钢也由峰时效（５１０℃／１０ｍｉｎ）→过时效（５１０℃／５ｈ）→明显过时效转变。５１０℃５ｈ合会开始发生逆转变。     

先进的宇航试验舱温控系统

介绍了中国新一代宇航试验舱的温控系统。该温控系统设计思想先进、结构新颖。在直径２．３ｍ,长２ｍ的封闭舱体控温面上,实现了０℃～５０℃的任意温度定点控制及９０ｍｉｎ内的正弦波、梯形波、三角波的周期变化;在整个控温面上温度非均匀性（均方根偏差）小于０．３℃,远远超过了非均匀度±１℃、控制精度±２℃的原设计指标。     

SENSOR FAILURE DETECTION AND SIGNAL RECOVERY BASED ON BP NEURAL NETWORK

Manyhighpefformancecontrolsystemsmusthavefauhtolerantabilityagainstsensorfailures.Theapplicationofprevioussensorfailuredetectinnmethods,mostlybasedonanalyti-calredundancy['Jlislimitedbecausetheyrequireaprecise.mathematicalmedel.BPneuralnetwork(BPNN)isabletolearnanycomplicatedcontinuousnonlinearfunctions,therefore,itcanbeusedtodetectsensorfailuresandrecoverthesignalforthefailedsensor'Recentpubli-cationshavedemonstratedtheuseofBPNNfordetectingsomkindofsensorfailuresandre-coveringthefailedsen…     

基于AD736真有效值测量的发电机电压控制技术研究

针对电励磁同步发电机电压控制技术存在参数漂移、工作不稳定、电压畸变导致控制参数超差等诸多问题,介绍一种电励磁同步发电机数字电压控制技术,通过AD736高精度芯片测量交流电压真有效值,并采用基于双闭环数字PI算法的电压控制技术,开展了发电机电压数字控制器研制。经试验考核,该控制器性能指标满足设计要求,达到了预期目标。     

多孔金属夹芯结构的抗爆性能研究

多孔金属夹芯结构已被广泛应用于航空航天等领域,研究其抗爆吸能性能具有十分重要的意义。分别对金属空心小球和泡沫铝两种夹芯壳结构在TNT爆炸载荷作用下的抗爆性能进行爆炸实验,并采用AN-SYS/LS-DYNA有限元软件进行数值模拟研究。结果表明:金属空心小球夹芯结构作为抗爆吸能结构是可行的;在结构框架尺寸与质量相同时,内面板厚外面板薄的夹芯结构具有更好的抗变形能力,内面板薄外面板厚的夹芯结构则具有更好的吸能特性;在结构框架尺寸与质量相同时,负梯度夹芯结构、并列型小球夹芯结构、小半径小球夹芯结构具有更好的抵抗爆炸载荷和吸收冲击能量的性能;在结构框架尺寸与质量相同时,金属空心小球夹芯结构的整体强度更高,而泡沫铝夹芯结构能更充分地发挥芯层的缓冲性能。     

SINS辅助的星敏感器在线标定方法

航天器在飞行过程中,星敏感器受到外界温度、地面标定精度等因素影响存在较大的安装误差,这将严重影响星敏感器的定姿精度。为提高星敏感器精度,对其安装误差进行严格的在轨实时标定与修正是确保星敏感器测量精度的关键。提出了一种SINS辅助的在线标定方法,将SINS/星敏感器输出的姿态信息进行配准,构建了组合导航系统的Kalman滤波模型。该方法只需航天器在飞行过程中做简单的机动,即可对星敏感器的安装误差角进行实时在线标定。仿真结果表明,采用该标定方法可使星敏感器和惯导的安装误差角的总体估计率达到95%以上,具有较高的工程应用价值。     

下缘板孔对涡轮叶片尾缘内冷通道流动换热影响的数值研究

涡轮叶片下缘板出气孔对内冷通道的流动和换热性能有较大影响。通过数值模拟方法研究下缘板出 气孔对尾缘和下缘板双路出气涡轮叶片尾缘内冷通道内的流动和换热特性,对比分析孔径、孔形和孔位置对尾 缘溢流孔流量系数、尾缘出流比、尾缘通道内总压系数和尾缘内冷腔壁面换热特性的影响。结果表明:下缘板 出气孔孔径对流量系数分布的影响显著,孔径增大,尾缘溢流孔流量系数下降,尾缘出流比减小,尾缘内冷通道 内压力损失降低,内冷腔平均换热系数增大;孔形对上游内冷通道内流动和换热几乎没有影响;孔位置变化对 内冷通道壁面整体的换热系数影响很小,对局部影响较大。     

无人机复合材料夹层结构件工装的制造

阐述了无人机蜂窝夹芯复合材料结构件 工艺装备的设计与制造的发展过程及各种加工方法的 优缺点。