面向对象技术的防空导弹Simulink建模与仿真

为防空导弹系统性能改进研究和优化设计,提出了一种新的方法,首先给出了一般防空导弹制导控制系统的数学模型,并采用面向对象建模技术结合动态仿真软件Simulink建立了仿真模型并进行了仿真研究,该模型具有容易理解,可重复使用,易于扩展等优点,即通过部分模块更换或改变参数等就可对该系统在其他条件下进行仿真,仿真结果和实际遥测数据基本吻合,表明了该模型和方法的有效性和实用性。     

利用红外加热笼进行低热流模拟的设计方法研究

在航天器热平衡试验中,散热面区域的低热流密度要求往往难以实现。在以往的试验中,考虑到加热笼覆盖系数对热流密度均匀性的影响,通常选用红外灯阵作为主要的外热流模拟装置。但是红外灯阵体积和热容较大,形状适应性不强,对试验容器空间要求较高。文章利用仿真的手段研究了加热笼的覆盖系数对热流密度均匀性的影响,探讨了利用红外加热笼进行低热流模拟的可行性。     

Space–Time Structure of Energetic Electron Precipitations according to the Data of Balloon Observations and Polar Satellite Measurements on February 1–6, 2015

Cosmic Research - The results of an analysis of the space–time characteristics and dynamics of precipitations of magnetospheric electrons with energies in the range from 0.1 to 0.7 MeV are...     

Erratum to: Determination of the Probability of Collision of Near-Earth Space Objects Taking into Account Form and Orientation

Cosmic Research - An Erratum to this paper has been published: https://doi.org/10.1134/S0010952521120030     

China's Space Activities In 2007

THE FOURTH BEIDOU NAVIGATION EXPERIMENTAL SATELLITE LAUNCHED The fourth Beidou experimental navigation satellite was launched into snace aton a LM-3A launch vehicle at Xichang Satellite Launch Center on February 3 at 00:28(Beijing Time).24 minutes later,the satellite separated from the launch vehicle and     

Debut Flight Of LM-3C:Launching Tianlian-1 Successfully

FY-3A,the first satellite of China's new generation of polar-orbiting meteorological satellites,was launched into space atop a modified LM-4C launch vehicle.The satellite separated from the rocket 19 minutes after the takeoff.Flying at an altitude of 807km with an inclination of 98.8 degrees,the satellite circles in polar orbit 14 times everyday,covering the whole globe twice a day. FY-3A has a design lifetime of three years.Weighing 2295kg,the three-axis stabilized satellite is equipped with 11 remote s...     

The mass loss of spacecraft polyimide films under the action of atomic oxygen and vacuum ultraviolet radiation

The threshold values of the annual fluence of atomic oxygen (F _AO ≈ 10²⁰ cm^?2), as well as the ratios of the energy-flux density of vacuum ultraviolet radiation of the solar spectrum to the flux density of atomic oxygen (Φ _ν /Φ _AO ≈ 8 × 10^?15 mJ) were determined, which are characterized the influence of the synergistic effect on the mass loss of Kapton-H, PM-A, and PM-1E polyimide films, which are spacecraft materials.     

大直径铝合金铆钉以铆代螺可行性试验研究

针对双层铝合金板铆接结构,通过电磁铆接工艺试验,分析Φ10mm-2A10铝合金铆钉镦头的微观组织,与钢质螺栓连接接头对比评价了铆接接头的力学性能。研究发现,随放电电压的增加,铆钉镦头直径逐渐增加、高度逐渐降低。铆钉镦头以绝热剪切为主要变形模式。铆接接头的最大剪切和拉脱载荷分别为23.3k N和35.0k N,均高于钢质螺栓连接接头,并且相对于螺接接头可减重15.8%。     

Shock protection of penetrator-based instrumentation via a sublimation approach

It is often necessary for space-borne instrumentation to cope with substantial levels of shock acceleration both in the initial launch phase, as well as during entry, descent and landing in the case of planetary exploration. Current plans for a new generation of penetrator-based space missions will subject the associated on-board instrumentation to far greater levels of shock, and ways must therefore be found to either ruggedize or else protect any sensitive components during the impact phase. In this paper, we present an innovative method of shock protection that is suited for use in a number of planetary environments, based upon the temporary encapsulation of said components within a waxy solid which may then be sublimated to return the instrument back to its normal operation. We have tested this method experimentally using micromachined silicon suspensions under applied shock loads of up to 15,000g, and found that these were able to survive without incurring damage. Furthermore, quality factor measurements undertaken on these suspensions indicate that their mechanical performance remains unaffected by the encapsulation and subsequent sublimation process.