提高竞争力 推动军工企业管理模式创新

通过介绍目前军工制造企业特点,提出军工制造企业管理模式必须得到创新。针对管理模式创新的原则,并分析目前面临问题,阐述了创新的途径和策略,为军工制造企业管理模式的创新提供了借鉴。     

A Self-organizing Bearings-only Target Tracking Algorithm in Wireless Sensor Network

In the bearings-only target tracking, wireless sensor network (WSN) collects observations of the target direction at various nodes and uses an adaptive filter to combine them for target tracking. An efficient network management is necessary to gain an optimal tradeoff between locating accuracy and energy consumption. This article proposes a self-organizing target tracking algorithm to select the most beneficial subset of nodes to track the target at every snapshot. Compared with traditional methods, this scheme avoids the need for keeping global position information of the network as in greedy selection. Each node judges its future usefulness depending on the knowledge of its own position and using simple mathematics computation. Simulations indicate that this scheme has locating accuracy comparable to the global greedy algorithm. Also, it has good robustness against node failure and autonomous adaptability to the change of the network scale. Furthermore, this algorithm consumes limited energy because only a portion of nodes partakes in the selection at every snapshot.     

热静液挤压工艺对WCu40电极材料组织性能的影响

简介了ＷＣｕ４０电极材料的研制工艺，着重分析了工艺参数对ＷＣｕ４０电有材料组织性能的影响。     

用等电平测量辐射计接收机的线性度

微波辐射计接收机的线性度是表征输入噪声温度与输出电压间的关系，采用双位开关衰减器法实现等功率电平测量微波辐射计接收机的线性度。该方法是在已知输出温度的低温噪声源之后，接有一个双位开关衰减器，这个双位开关衰减器只有二个档位，要么是直通，要么是通过一个固定的小衰减量。多次交替开关，可使达到接收机的输入量每次的增加是个相同量，这样就能完成接收机线性度的准确测量。简述测量原理、方法和测量不确定度分析。     

基于有限元方法的并联机床模态分析

并联机床的模态分析有着重要的意义。本文针对3—HSS型并联机床,利用大型有限元软件ANSYS,对此并联机床进行了模态分析,分别获得了该机床的低阶固有频率及其对应的振型图,通过振动动画,分析了六阶模态的振动规律,找到了机床的薄弱环节,为机床的结构设计和动力学分析提供了依据。     

强化安全管理作用增强飞行保障能力

空中交通管制部门的安全运行在全民航的安全生产工作中占有重要地位，而空管设备保障部门的设备保障工作则是做好空管工作的基础，直接关系到空管工作的成效。现在，随着空中飞行流量的不断加大，高新技术的飞速发展和在民航的应用，使得空管设备保障部门所属设备越来越复杂，科技含量也越来越高；伴随着空管体制改革的深入进行，领导干部职位与基层值班员岗位也在不断地变动。     

Deriving remote sensing reflectance from turbid Case II waters using green-shortwave infrared bands based model

The objectives of this study are to validate the applicability of a shortwave infrared atmospheric correction model (SWIR-based model) in deriving remote sensing reflectance in turbid Case II waters, and to improve that model using a proposed green-shortwave infrared model (GSWIR-based model). In a GSWIR-based model, the aerosol type is determined by a SWIR-based model and the reflectance due to aerosol scattering is calculated using spectral slope technology. In this study, field measurements collected from three independent cruises from two different Case II waters were used to compare models. The results indicate that both SWIR- and GSWIR-based models can be used to derive the remote sensing reflectance at visible wavelengths in turbid Case II waters, but GSWIR-based models are superior to SWIR-based models. Using the GSWIR-based model decreases uncertainty in remote sensing reflectance retrievals in turbid Case II waters by 2.6–12.1%. In addition, GSWIR-based model’s sensitivity to user-supplied parameters was determined using the numerical method, which indicated that the GSWIR-based model is more sensitive to the uncertainty of spectral slope technology than to that of aerosol type retrieval methodology. Due to much lower noise tolerance of GSWIR-based model in the blue and near-infrared regions, the GSWIR-based model performs poorly in determining remote sensing reflectance at these wavelengths, which is consistent with the GSWIR-based model’s accuracy evaluation results.     

Characteristics of the seasonal variation of the global tropopause revealed by COSMIC/GPS data

Using the Global Navigation Satellite System (GNSS) radio occultation observations from Formosa Satellite mission-3/Constellation Observing System for Meteorology, Ionosphere, and Climate (FORMOSAT-3/COSMIC) from 2007 to 2012, the climatological characteristics of the global tropopause was studied, with the following features identified. The overall results generally agree with previous studies. The tropopause has an obvious zonal structure, with more zonal characteristics in the Southern Hemisphere than the Northern Hemisphere. The vertical shape of the tropopause is sharp in the tropics and broad in the sub-tropical latitudes, with the sharpest latitudinal gradient in the mid-latitudes of both hemispheres. The global tropopause exists in a large range between 8 km and 17 km (or between 100 hPa and 340 hPa). The highest tropopause is over the South Asian monsoon regions for the entire year. The spatial structure of the tropopause in the polar region is of concentric structure, with an altitude between 7.5 km and 10 km. It is more symmetric in the Antarctic than the Arctic. Differing from other places, the height of the tropopause in the Antarctic is higher in winter as opposed to summer. The tropopause has distinct seasonal variability, especially in polar regions.     

Silver Film Growth on Glass Ceramic by Radio Frequency Magnetron Sputtering

Thin silver films are deposited by radio frequency magnetron sputtering on glass ceramic at room temperature.Variations of sputtering power,bios voltage and power density are carried out for each deposition,then parts of as-deposited samples are subjected to annealing at 600 ℃ within a vacuum chamber.Structural properties are studied by X-ray diffraction(XRD),scanning electron microscope(SEM)and laser scanning confocal microscope(LSCM).It is shown that structural properties have a strong dependency on sputtering power and annealing temperature.Electrical contact resistance measured by a four point probe instrument is directly affected by the thickness of films.It is also found that the film conductivity,especially in thinner films,is improved by the increasing grain size.Finally,the film adhesion is observed by scratch tests.And the adhesive ability deposited by radio frequency magnetron sputtering shows a better performance than that produced by traditional methods.     

Dry Grinding of Titanium Alloy Using Brazed Monolayer cBN Wheels Coated with Graphite Lubricant

The purpose of this study is to investigate the effect of graphite lubricant on the dry grinding performance of Ti-6Al-4Valloy,using graphite-coated,brazed monolayer,cubic boron nitride(cBN)wheels.Brazed monolayer cBN wheels both with and without a coating of polymer-based graphite lubricant are fabricated and subsequently compared for grinding performance based on measurements of grinding temperature,surface microstructure and grinding.In terms of grinding temperature,considerable improvement in dry grinding performance of titanium alloy is achieved using coated brazed monolayer cBN wheels,with 42%—47%reduction in grinding temperature as opposed to uncoated wheels.The grinding force ratio with the coated wheels is observed to remain between 1.45to1.85despite material removal rates reaching up to 1 950mm3/mm.No tangible change in ground titanium surface microstructure is noted as a result of grinding with the graphite coated wheels as opposed to the uncoated ones.