过滤式阴极电弧沉积类金刚石薄膜的特性分析

利用自行研制的过滤式阴极电弧沉积装置,在硅片和高速钢基体材料上获得了类金刚石薄膜,分别采用扫描电镜、原子力显微镜、喇曼光谱以及磨损实验等手段对薄膜进行了分析研究。结果表明,所获得的类金刚石薄膜为非晶态,sp3含量最高达70%;基体材料对成膜质量影响较大,在硅片上薄膜的摩擦系数可达0.08;同时偏压的变化会引起喇曼谱线中D峰和G峰位置向低频移动,半高宽σG增大、σD减小。     

柔壁自适应风洞低超音速实验技术研究

低超音速三维模型实验是在二维柔壁自适应风洞中进行的。将Wedemeyer理论推广到超音速流动,建立了洞壁调整量的计算方法;解决了洞壁预调量效应的计算问题。在此基础上提出洞壁自适应调整方案,它可用于堵塞比较大的模型实验和任意初始壁面。按此洞壁调整方案所作实验结果表明,二维柔壁自适应风洞作超音速三维模型实验时,可有效地抑制压缩、膨胀波经洞壁反射后对气动数据的影响。其消波效果和三维自适应壁风洞的消波效果基本相同,主激波反射的消波效果甚至优于后者。     

几种大平面平面度测量方法比较

叙述了几种大平面平面度的测量方法,分析了间接测量法、激光双光束扫描法、激光准直扫射法、衍射平面基准法、液面法等几种方法的特点及其测量误差。     

无头铆钉成型过程的有限元仿真与试验分析

采用ABAQUS建立有限元分析模型,分析了66°锥形铆模压铆无头铆钉的成型过程。对成型后的试片进行了力学及金相分析,并将结果与普通半圆头铆钉进行对比。研究结果表明,无头铆钉的压铆变形过程为钉杆中间最早涨粗,墩头部分成型,随后钉杆部分逐步与孔壁均匀挤压的过程;随着压铆位移的增加,无头铆钉拉脱强度及剪切强度均呈上升趋势;与传统平铆模成型的半圆头铆钉相比,在锥形铆模的作用下,金属材料向钉杆流动更加均匀,墩头两侧的绝热剪切效应明显弱化。     

Experimental Study on Emission Performance of an LPP/TVC

A key issue in the commercial aircraft engine design is environmental acceptability, and designers are continually challenged to reduce emissions. In this paper, an experimental investigation is performed to evaluate the emission performance of a liquid-fueled trapped vortex combustor (TVC) under lean premixed prevaporized (LPP) mode. When operating as an LPP system, a TVC is fueled both in the cavities and in the main stream. The correlations between the emission performance and the total excess air ratio, the positions (4 positions) of the fuel injectors in the main stream, and the inlet temperature are obtained. Experi- mental results show that both the volume concentrations of unburnt hydrocarbon (UHC) and NOx (NO, NO2 usually grouped together as NOx) increase with the increase of total excess air ratio from 1.5 to 3.0; the emission performance relies heavily on the position of the main stream injector, and the best performance is achieved at Position 4 in the experiments; the increase of the inlet temperature impacts on the emission performance positively; the smallest volume concentrations of UHC and NOx obtained in the experiment are 94×10 6 and 2.3×10 6 respectively. This paper validates the feasibility of low emissions for an LPP/TVC and provides a reference for further optimization of TVCs.     

离子推力器放电室参数在线优化实验研究

为了改进氙离子推力器传统优化实验方法,针对环切场放电室设计多维优化调节机构,通过步进电机配合电磁铁实现放电室设计参数的在线实时调节。实验中在线调节放电室长径比、中间磁极靴位置、阴极顶位置等参数,得到了放电室性能影响规律,经迭代实验获取了优化后的放电室构型及磁场参数。优化后的推力器性能曲线"膝点"较正交实验结果更加靠后,在工质利用率80%~90%区间内,束离子电离能耗低于正交实验优化结果。在线优化实验方法极大缩短了离子推力器设计周期,降低研制成本,并弥补了传统方法需多次破空导致参数一致性差的不足。     

Detection of aerosol pollution sources during sandstorms in Northwestern China using remote sensed and model simulated data

The present paper has used a comprehensive approach to study atmosphere pollution sources including the study of vertical distribution characteristics, the epicenters of occurrence and transport of atmospheric aerosol in North-West China under intensive dust storm registered in all cities of the region in April 2014. To achieve this goal, the remote sensing data using Moderate Resolution Imaging Spectroradiometer satellite (MODIS) as well as model-simulated data, were used, which facilitate tracking the sources, routes, and spatial extent of dust storms. The results of the study have shown strong territory pollution with aerosol during sandstorm. According to ground-based air quality monitoring stations data, concentrations of PM₁₀ and PM_2.5 exceeded 400?μg/m³ and 150?μg/m³, respectively, the ratio PM_2.5/PM₁₀ being within the range of 0.123–0.661. According to MODIS/Terra Collection 6 Level-2 aerosol products data and the Deep Blue algorithm data, the aerosol optical depth (AOD) at 550?nm in the pollution epicenter was within 0.75–1. The vertical distribution of aerosols indicates that the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) 532?nm total attenuates backscatter coefficient ranges from 0.01 to 0.0001?km^?1?×?sr^?1 with the distribution of the main types of aerosols in the troposphere of the region within 0–12.5?km, where the most severe aerosol contamination is observed in the lower troposphere (at 3–6?km). According to satellite sounding and model-simulated data, the sources of pollution are the deserted regions of Northern and Northwestern China.     

高压脉冲电子束的控制及其对焊缝形貌影响

研制出一台150 kV/30 kW高压脉冲电子束焊机,介绍了控制脉冲束流产生的偏压脉冲电源拓扑电路结构及脉冲束流频率、占空比、束流基值、束流峰值的调节控制技术.在0~1 kHz频率范围内,该电源可输出最大幅值200 mA的脉冲电子束束流,且工艺参数调节方便.分别采用脉冲束流与连续束流电子束工艺焊接了1Cr18Ni9Ti奥氏体不锈钢,对不同工艺的焊缝形貌进行了对比分析.与连续束流电子束焊接工艺相比,采用脉冲电子束焊接工艺的焊缝熔深增加,深宽比增大;对于脉冲电子束焊接工艺,占空比给定时,随着束流频率增加,焊接缺陷减少.试验结果表明:脉冲束流频率、占空比是影响焊缝成形的关键工艺参数;脉冲调制方式控制偏压是获得高压脉冲电子束的理想控制技术之一.      

基于协同决策的多航站楼停机位实时分配算法

针对多航站楼机场停机位实时指派问题,提出了基于协同决策并考虑航空公司时隙交换公平性的机位实时指派算法。该算法将多航站楼资源的可共享性考虑到指派算法中,以最小延误费用原则为约束,采用混合集合规划进行指派模型的建立与求解。该算法在保证多航站楼停机位资源有效共享的前提下,充分实现了航空公司时隙交换的公平性,并且使延误引起的多方成本最小化。算例说明:本文提出的算法可以有效解决多航站楼的机位实时分配问题。     

屈服假塑性凝胶模拟液直圆管流变和流动特性分析

通过理论分析和试验研究,进行了某型凝胶模拟液在直圆管内的流变和流动特性研究。研究结果表明：该凝胶模拟液具有明显的屈服应力;由于屈服应力的作用,直圆管中心明显地分为剪切流动区和柱塞流动区,柱塞流动区半径与屈服应力成正比,与压力梯度成反比;当流量恒定时,沿程压降随屈服应力的增大而增大;当压力梯度保持不变时,流量随屈服应力的增大而减小。