C/SiC复合材料紧固件拉-拉疲劳行为研究

为了研究C/SiC复合材料紧固件的拉-拉疲劳行为,在疲劳应力比为0. 1、加载频率为10 Hz的条件下对不同应力水平的疲劳寿命进行统计。采用断口分析和金相分析方法对C/SiC复合材料螺钉疲劳破坏的细观机制进行了研究。结果表明:C/SiC复合材料螺钉拉-拉疲劳包含拉断疲劳及拉脱疲劳两种失效形式;基于双参数幂指数形式的寿命模型,两种失效形式的疲劳寿命经验公式相似;C/SiC复合材料螺钉的疲劳极限约为拉伸强度的65%～70%,若最大疲劳应力大于0. 7σmax,其材料损伤随循环次数增多而明显增大。     

压电致动器扑翼结构动力学仿真

采用传统扑动机构的微型扑翼,气动效率低、扑动能耗大。采用压电致动器的微型扑翼通过压电材料进行致动使机翼产生上下扑动,有效地将扑动机构和机翼两个主要系统进行集成,不仅节省重量,同时它具有任务变形自适应能力强、气动效率高和扑动能耗小的特点。通过PCL语言建立采用压电致动器的扑翼有限元模型,结合同尺寸扑翼气动力试验数据,进行采用压电致动器扑翼结构仿真。利用仿真结果研制采用压电致动器扑翼原理样机,研究表明,采用压电致动器后扑翼扑动频率得到明显提高,压电片可有效控制机翼的弯扭变形,有助于提高扑翼的气动效率。     

固体火箭发动机零维两相燃烧室压强计算方法研究

为了更准确地预估含金属燃料固体火箭发动机的燃烧室压强,在压强计算中考虑两相流的影响,从一维两相喷管流动的求解出发,通过两相平衡流模型、两相常滞后模型、两相等温流模型、颗粒定温模型等模型的简化,分别推导不同模型下喷管中两相混合物的流量计算公式,再把流量公式应用到发动机零维内弹道理论中,推导并简化得到零维燃烧室平衡压强的计算公式。把压强公式用于HTPB推进剂固体火箭发动机和铝冰固体火箭发动机的燃烧室压强计算,结果表明,当固体推进剂中金属含量较高时(如铝含量为21%的HTPB推进剂发动机),用传统零维燃烧室压强公式预估的压强与实验误差较大,而使用合适的两相流模型和对应的零维燃烧室压强计算方法,在HTPB发动机中,能把压强预估结果与实验的误差降低到6%以内。如果使用多维内流场计算的方法,燃烧室压强预测结果的误差将下降到2.5%以内。结论发现在含金属固体火箭发动机的燃烧室压强计算中,考虑两相流的影响是必要的,而使用两相流修正后的零维燃烧室压强计算公式能够快速、较准确地预估这些发动机的燃烧室压强。     

热障涂层在涡轮叶片应用中的热防护有效性

建立了含热障涂层的涡轮叶片简化传热模型,通过理论推导建立了热障涂层的有效性判据,并基于此进行了热防护有效性分析。理论分析与数值实验表明:由热障涂层带来的复合传热表面传热系数的变化会显著影响热障涂层的热防护效果;在发动机典型工况下,对于处于高温区的高压涡轮叶片前缘处,热障涂层引起的复合传热表面传热系数变化率最大值的范围为1.25%~10.83%以满足热防护有效性要求。在工程中应特别注意由于热障涂层的应用带来的复合传热表面传热系数的变化,否则会导致热防护失效,甚至产生反效果。      

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

An experimental system for release simulation of internal stores in a supersonic wind tunnel

Aerodynamic parameters obtained from separation experiments of internal stores in a wind tunnel are significant in aircraft designs. Accurate wind tunnel tests can help to improve the release stability of the stores and in-flight safety of the aircrafts in supersonic environments.A simulative system for free drop experiments of internal stores based on a practical project is provided in this paper. The system contains a store release mechanism, a control system and an attitude measurement system. The release mechanism adopts a six-bar linkage driven by a cylinder, which ensures the release stability. The structure and initial aerodynamic parameters of the stores are also designed and adjusted. A high speed vision measurement system for high speed rolling targets is utilized to measure the pose parameters of the internal store models and an optimizing method for the coordinates of markers is presented based on a priori model. The experimental results show excellent repeatability of the system, and indicate that the position measurement precision is less than0.13 mm, and the attitude measurement precision for pitch and yaw angles is less than 0.126°, satisfying the requirements of practical wind tunnel tests. A separation experiment for the internal stores is also conducted in the FL-3 wind tunnel of China Aerodynamics Research Institute.     

电网电压不平衡及谐波畸变时基波电压正负序分量分离新方法

针对传统锁相环(PLL)在电网电压不平衡及谐波畸变下利用常规软件锁相环不能准确获取相位的问题,提出了一种新的正负序分量分离新方法。利用了相序解耦谐振控制器能去除高次谐波和延时信号消除(DSC)法可滤除特定谐波的特性,将相序解耦谐振和延时信号消除法结合起来,达到更好的正负序分量分离的效果。最后,采用MATLAB/Simulink软件仿真结果证明了所提出方法的可行性和有效性。     

某型民用运输机主起落架连接区结构静力试验

飞机静力试验是飞机试验的重要内容之一,是验证飞机结构强度和静力分析正确性的重要手段。为验证某型民用运输机主起落架连接区结构满足静强度要求,以及有限元计算分析的正确性,在静力试验飞机上进行了主起落架连接区结构静力试验。通过全机有限元模型和细节有限元模型分析计算,进行加载、应力\应变、位移试验数据与有限元计算值的分析对比,计算值与试验数据符合较好。     

潜载导弹水下弹射过程数值仿真

针对无横流影响的潜射导弹水下弹射过程瞬态流场变化情况,建立了多相流数学模型。考虑空穴模型,运用动网格技术,再现了导弹水下弹射过程的筒口气团、肩空泡的演变过程以及弹体底部、固壁的压力变化。仿真结果表明,筒口效应导致固壁各处的压力阶跃;筒口气团收缩拉断的过程中,闭合点处形成高压区,导致固壁各处压力剧烈上升,同时闭合点处产生的反射流撞击导弹底部引起压力变化。     

基于Patran/Nastran 和Hypersizer的复合材料后机身加筋结构形式选择分析

针对复合材料后机身加筋壁板构型选择问题,采用有限元前后置处理软件Patran建立有限元模型,使用有限元分析软件Nastran进行初步分析,利用复合材料结构分析与优化软件Hypersizer进行结构形式的优化计算分析,优选出后机身壁板最佳结构形式。通过计算分析,得出有意义的工程经验。