过氧化氢分解后燃气喷注压降对发生器非正常熄火的影响

通过试验和数值仿真分析了过氧化氢催化分解后燃气通过同轴喷嘴的喷注压降对过氧化氢/低浓度酒精燃气发生器非正常熄火的影响。研究表明：燃气喷注压降或喷注速度是影响发生器正常工作的重要因素,当燃气喷注压降为1.0MPa时,喷注速度过大,火焰无法在燃烧室内稳定,造成熄火;而当燃气喷注压降为0.2MPa后,喷注速度降低,火焰稳定并维持正常燃烧。     

某型导弹靶标研制的风险评估研究

武器装备研制过程存在各种风险,准确地对风险进行评估,可有效减少风险造成的损失。针对武器装备的研制风险,介绍了风险评估的方法,并结合风险因子、技术特征因子和实验条件因子,给出风险计算公式。最后结合某导弹靶标系统进行了风险评估。     

开式整体叶盘四坐标高效开槽插铣工艺方法

 整体叶盘的加工余量主要是在其通道开槽粗加工阶段去除的,提高通道开槽切削效率是实现叶盘高效加工的关键。根据开式整体叶盘通道的结构特点,提出了四坐标插铣开槽高效低成本粗加工方法。通过叶盘叶片偏置面的直纹包络面逼近,确定叶盘通道粗加工区域,给出了四坐标插铣刀位轨迹生成算法。该方法有效解决了直纹面逼近的曲面边界问题,并通过对叶片偏置面的直纹逼近从根本上避免了刀位轨迹计算时误差的产生。实验表明,与传统的侧铣开槽粗加工相比,采用四坐标插铣方式切削力可降低60%,粗加工效率可提高1倍以上。     

导弹及固体火箭的外防护材料

叙述了导弹火箭系统外绝热防护，抗核辐射并介绍了作为固体火箭发动机结构材料的增强纤维／树脂、等复合材料抗氧化途径。     

多台系统Weibull过程的Bayes统计推断方法

本文的目的是要给出多台系统Weibull过程的Bayes推断方法。获得了尺度参数、形状参数以及系统能达到的MTBF的Bayes点估计和区间估计。某些估计只涉及到一重数值积分。最后,用一个实例说明这些方法。     

Performance evaluation of track fusion with information matrixfilter

In a multisensor environment, each sensor detects multiple targets and creates corresponding tracks. Fusion of tracks from these, possibly dissimilar, sensors yields more accurate kinematic and attribute information regarding the target. Two methodologies have been employed for such purpose, which are: measurement fusion and state vector fusion. It is well known that the measurement fusion approach is optimal but computationally inefficient and the state vector fusion algorithms are more efficient but suboptimal, in general. This is so because the state vector estimates to be fused obtained from two sensors, are not conditionally independent in general due to the common process noise from the target being tracked. It is to be noted that there are three approaches to state vector fusion, which are: weighted covariance, information matrix, and pseudomeasurement. This research is restricted solely to performance evaluation of the information matrix form of state vector fusion. Closed-form analytical solution of steady state fused covariance has been derived as a measure of performance using this approach. Note that the results are derived under the assumptions that the two sensors are synchronized and no misassociation or merged measurement is considered in the study. Results are compared with those using Monte Carlo simulation, which was used in the past to predict fusion system performance by various authors. These results provide additional insight into the mechanism of track fusion and greatly simplify evaluation of fusion performance. In addition, availability of such a solution facilitates the trade-off studies for designing fusion systems under various operating conditions     

无独立线路标准化电位差计的自检

无独立线路标准化电位差计按单个电阻进行元件检定不方便、时间长、过程复杂。采用ｊ＋１盘的１０／Σ１Ｕｉ＾ｊ＋１示值检定ｊ盘每个步进值的电压比较法，可缩短时间，方便易行。提高了检定精度，并推导出系列计算公式和应用实例。     

红宝石球轴承在低温条件下的静态热导

通过红宝石球轴承与不锈钢球轴承的实测热导比较，说明了在低温条件下红宝石球轴承的热导较高，热导受温度和负荷的影响较大，但是红宝石球轴承的接触热导较小。     

材料韧脆转移过程的数学模拟和实验标定

研究了Cr24Al2Si铁素体不锈钢韧脆转移过程的性能-温度曲线的数学模拟,找到了其最佳的韧脆转移数学模型。通过韧脆转移的数学模型,还可以找到能量韧脆转移温度T_C与无塑韧脆转移温度T_(NDT)之间的定量换算关系。 上述关系,不仅可以成为确定韧脆转移温度通用准则,提供一种定量分析的数学方法,而且使韧脆转移曲线转化为韧脆机制转移曲线,从而为建立冷脆断裂机制图奠定了基础。     

分形表面的结构函数及其应用

介绍了用于表征分形表面的结构函数的定义，起因以及与其它统计量的关系，并给出了实验和结果分析。