数控机床铣螺纹用盘形铣刀的近似造型及误差计算

在数控铣床上加工螺纹，需要设计盘形铣刀，本文求导了铣刀宽度计算公式，分析了产生误差的原因，并提出了改进措施。     

一种新型测距仪的研制

介绍了一种在中，小范围内，采用激光定位，超声测距的新型测量仪器，该仪器以单片微处理器为核心，对不同的测量距离，采用不同频率的超声波，结合信号处理方法，从而实现０．６～１４ｍ范围内高精度实时测量目标距离，其测量相对误差优于１％。     

Morphology and Frictional Characteristics Under Electrical Currents of Al203/Cu Composites Prepared by Internal Oxidation

Two AhO3/Cu composites containing 0.24 wt.% A1203 and 0.60 wt.% A1203 separately are prepared by internal oxidation.Effectsof sliding speed and pressure on the fi-ictional characteristics of the composites and copper against brass are investigated and compared.The changes in morphology of the sliding surface and subsurface are examined with scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS).The results show that the wear resistance of the AI203/Cu composites is superior to that of copperunder the same conditions.Under a given electrical current,the wear rate of AI203/Cu composites decreases as the AleO3-content increases.However,the wear rates of the Al203/Cu composites and copper increase as the sliding speed and pressure increase under drysliding condition.The main wear mechanisms for AleO3/Cu composites are of abrasion and adhesion;for copper,it is adhesion,although wear by oxidation and electrical erosion can also be observed as the speed and pressure rise.     

三维数模随动下的机翼结构重量优化

目前,基于快速建模下的重量重心估算系统得到了快速发展。为了进一步提高结构重量估算精度,研究了如何在重量重心快速分析(WCGA)系统环境中构建优化模块。以机翼结构重量优化为例,提出优化流程,对优化模块功能进行分解,给出模型简化要求。以A320飞机机翼为例,对梁和长桁进行优化,结果显示,经过优化,有效减轻了结构重量,且相比于传统的减重优化设计方法,极大提高了计算效率。     

圆柱度误差最小区域评定方法述评

本文简介圆柱度误差评定的常用数学模型，并对用最小区域法评定圆柱度误差的几种近似方法及其优缺点展开讨论。     

Ground experiments of Chang’e-5 lunar regolith penetrating radar

The Lunar Regolith Penetrating Radar (LRPR) is an Ultra-Wideband (UWB) array-based Ground penetrating radar (GPR) onboard the lander of Chang’e-5 (CE-5) mission. The primary scientific objectives of the LRPR are to probe the thickness and structure of lunar regolith of the landing site, and support the drilling and sampling process. In order to evaluate the performance of the LRPR, a series of ground experiments are performed using the LRPR prototype mounted on a CE-5 lander model. The performance of the LRPR is evaluated by comparing the experimental data with the simulated data. Data processing and imaging method are verified, and the interferences from the lander and other aspects are analyzed. The results of the ground experiments and simulation demonstrate that the LRPR is able to meet the design requirement of 2-m detection depth. They also indicate that the upper and lower interfaces of the stratified structure in the lunar regolith can be well distinguished by the LRPR when the dielectric constant difference is greater than 0.3, and the imaging effect of the location under the dense antennas is better than that of other positions. However, the identification capability of the LRPR to the independent blocky objects is relatively poor mainly due to the clutters caused by the lander, the sparsity of the antenna elements compared to the size of the basalt block, the limited aperture of the antenna array, and the tail of the transmitted waveform.     

民用飞机辅助动力装置进气系统防火适航条款解读及试验研究

民用飞机辅助动力装置(简称APU)安装在飞机后机身APU舱内。APU舱作为民用飞机适航审查过程中的指定火区,需要经过严格的防火密封性验证。确保APU舱火区内可能发生的火灾危险不会传播到飞机的其他区域,影响到APU系统乃至整个飞机的安全运行。APU系统通过进气系统穿越APU舱防火墙与外界大气连通,为APU正常工作提供新鲜空气。进气系统穿越防火墙对APU舱的防火密封能力提出了很大考验。民用飞机适航审定也对APU进气系统防火性能提出了详细的适航条款要求。从APU进气系统防火适航条款解读入手,通过某型民用飞机APU进气系统防火适航审定实例,对进气系统防火从设计角度进行了研究,并且对适航审查时需要重点关注的防火密封区域进行了试验研究。     

多元共渗处理提高高速钢刀具加工钛合金的切削性能

用硬质合金切削钛合金已在许多航空工厂得到广泛应用,但在许多情况下仍然需要用高速钢刀具加工钛合金。采用多元共渗强化处理是一种改善高速钢刀具切削性能的方法。这种技术具有变形小、节能、成本低等特点。W18Cr4V高速钢经S-O-N-C-B五元强化共渗后,金相组织分为表层的化合物层(几μm)及其下的扩散层。扩散层由于渗入了固溶的C和N,并存在弥散的析出强化相,B元素使晶格严重畸变,扩散层的硬。     

载人航天器的发射窗口及太阳能帆板的最佳受晒

首先根据载人航天器轨道运行段的基本特征,利用球面三角公式推导了：①阳光方向与载人航天器太阳能帆板法向的最佳夹角公式;②圆轨道的受晒因子公式。然后根据理论分析,引入帆板的效率系数。最后借助于计算机代数ｍａｔｈｅｍａｔｉｃａ系统,建立了一种分析帆板最佳受晒的直观、清晰、简便的方法。所得的结论为确定载人航天器的发射窗口提供了依据。     

航天器热网络模型及其系数修正方法

叙述了目前航天器热网络模型与航天器实际换热之间的偏差,提出了利用航天器稳态热平衡试验结果进行热网络模型及其系数修正的方法。通过对某仪器舱热平衡试验数据的处理,实现了对该仪器舱热网络模型及其系数的修正,并对修正的结果进行了讨论。