基于最优控制的落角约束攻击设计

针对导弹落角控制和精度控制的矛盾,运用飞行力学原理和最优控制理论,以落地速度倾角作为终端约束,以脱靶量、最小能量为性能指标,给出了一种适用于攻击地面目标的最优导引律。设计了导弹三通道的PID控制器,最后进行了导弹的6DOF仿真研究,仿真验证了设计方法的有效性。     

Numerical Study of Parachute-Payload Land Site Distribution with Randomize Wind Gust Model

A parachute-payload model with randomize wind gust is developed to study the landing accuracy of the parachute decelerator system,which can be exactly described by the landing site distribution.The research focuses on the steady descent phase of the parachute descent process,so the parachute and the payload suspension formulation during the phase are mainly discussed.In addition,since the wind effects have a significant impact on the land site distribution of the passive decelerator system and it is difficult to obtain the exact wind profile in practice,major features of parachute-payload system are studied via the randomized wind gust formulation.As the randomized wind gust formulation is adopted,the wind effect can be considered without the exact wind gust profile and the parachute aerodynamic simulation can be fulfilled with uncertainties.Finally,the model is validated and discussed,and the parachute land site distributions with different wind randomize profiles are presented for comparison.The results show that when parachute is less stable,the land site tends to have a larger variance.     

基于VPM的教练机三维协同设计技术应用研究

随着CAD技术的发展,教练机的设计方式和设计手段发生了巨大变化.本文探讨了基于ENOVIA VPM平台应用CATIA软件三维协同设计技术,分析了教练机三维协同设计相关技术,着重介绍了三维协同设计技术在教练机设计中的应用.     

Platform LSF软件在高性能计算集群中的实施与应用

随着信息处理技术的精度、可靠度等要求的进一步提高,采用高性能计算集群系统已经成为数字化制造中的关键技术之一.本文结合高性能计算应用现状的不足,阐述了Platform LSF软件设计思想和目标,介绍了该软件的实施与应用情况.     

结冰风洞喷嘴雾化特性研究

结冰风洞试验段中的云雾通常由安装在稳定段的喷雾系统产生。喷雾系统雾化喷嘴的性能直接关系到结冰风洞试验段平均水滴直径(MVD)、液态水含量以及云雾均匀性等关键技术指标。在喷嘴试验台上分别使用PDI(相位多普勒干涉仪)及微流量计对小粒径雾化喷嘴的平均水滴直径(MVD)及水流量进行测量,得到了结冰风洞空气辅助雾化喷嘴的流量-粒径性能包线,同时,对喷嘴的供水、供气压力及其配比和水路节流管尺寸对喷嘴雾化性能的影响进行了研究。研究结果表明:喷嘴水、气压力差的大小和范围决定了喷嘴的粒径及调节比的范围。压差越大,粒径和水流量越大,压力差范围越大,调节比越大。减小喷嘴水路节流管的直径,可以增加喷嘴工作的水、气压力差范围,扩展喷嘴的流量-粒径包络线。最终的测试结果表明,结冰风洞所使用喷嘴 MVD 范围为7~70μm,水流量调节比为11.5,其参数调节范围优于国外同类风洞所使用雾化喷嘴。     

四孔交叠隧道下地铁运行对周边建筑物的振动响应分析

选取武汉地铁二号线和四号线中某区间的四孔交叠隧道为研究对象,采用有限元软件ANSYS进行数值模拟,探讨隧道周边建筑物在地铁运行下的振动响应规律。结果证实:建筑物各楼层的水平振动强度随楼层的增加而增加,竖向振动强度增幅不大。前5层中,竖直方向的振动比水平方向的振动强烈;第5层之后,各楼层的水平峰值加速度随着楼层的增加而显著增大。单孔隧道中有列车运行时,建筑物各楼层振动强度随隧道埋深的增大而减小,也随着到振源的水平距离的增大而减小,但埋深比水平距离的影响更明显。四孔隧道中均有列车运行时,建筑物同一楼层,内部各点的水平振动强度,随着距隧道中心线距离的增大,未表现出增大或减小的趋势,但靠近隧道一侧的竖向振动强度和竖向峰值位移比远离隧道一侧要大。     

不同温度下TC21钛合金等离子表面渗Cr层的摩擦磨损性能

为提高TC21合金的摩擦磨损性能,采用双辉等离子冶金技术在TC21合金表面制备渗Cr改性层,利用扫描电镜(Scanning electron microscope,SEM),能谱仪(Energy dispersive spectromenter,EDS),显微硬度仪和划痕仪等研究了渗Cr层的组织形貌特征、硬度及结合强度,并 在20,300,500 ℃条件下使用摩擦磨损试验机对基体及渗Cr层的摩擦磨损性能进行对比、探究,并分析磨损机理。结果表明：渗Cr层厚度为30μm,均匀致密,与基体结合力至少能承受64 N的垂直载荷;改性层表面硬度超过1 000 HV0.1,约为基体的3倍;TC21合金渗Cr后,不同温度下的减摩性能和耐磨性能均得到提高。在室温下TC21基体磨损机理主要是磨粒磨损、粘着磨损和氧化磨损,而渗Cr层的磨损机理主要是磨粒磨损;500 ℃时基体粘着磨损和氧化磨损程度变得更加严重,渗Cr层磨损机理是剥层磨损和氧化磨损。      

面向非合作目标抓捕的机械臂轨迹规划方法

文章针对非合作目标抓捕问题设计了基于误差反馈系数的机械臂轨迹规划算法.考虑到空间机械臂在轨服务要求,采用反作用零空间方法来规划机械臂运动轨迹以实现机械臂与航天器之间的协调运动.为避免在规划起始阶段位姿误差较大可能导致机械臂关节速度过大的问题,引入了位姿误差反馈系数.为对空间机械臂抓捕非合作目标的轨迹规划技术进行验证,搭建了地面半物理仿真系统.试验结果表明,通过合理选择位姿误差反馈系数,设计的轨迹规划算法能够使固定基座机械臂末端执行器以较为均匀的速度逼近非合作目标,并能以较高精度实现对非合作目标的抓捕.该试验可以为空间机械臂抓捕非合作目标的轨迹规划提供参考.     

Estimation of GPS instrumental biases from small scale network

With 4 GPS receivers located in the equatorial anomaly region in southeast China, this paper proposes a grid-based algorithm to determine the GPS satellites and receivers biases, and at the same time to derive the total electron content (TEC) with time resolution of 15 min and spatial resolution of 1° by 3.5° in latitude and longitude. By assuming that the TEC is identical at any point within a given grid block and the biases do not vary within a day, the algorithm arranges unknown biases and TECs with slant path TEC from the 4 receivers’ observations into a set of equations. Then the instrumental biases and the TECs are determined by using the least squares fitting technique. The performance of the method is examined by applying it to the GPS receiver chain observations selected from 16 geomagnetically quiet days in four seasons of 2006. It is found that the fitting agrees with the data very well, with goodness of fit ranging from 0.452 TECU to 1.914 TECU. Having a mean of 0.9 ns, the standard deviations for most of the GPS satellite biases are less than 1.0 ns for the 16 days. The GPS receiver biases are more stable than that of the GPS satellites. The standard deviation in the 4 receiver bias is from 0.370 ns to 0.855 ns, with a mean of 0.5 ns. Moreover, the instrumental biases are highly correlated with those derived from CODE and JPL with independent methods. The typical precision of the derived TEC is 5 TECU by a conservative estimation. These results indicate that the proposed algorithm is valid and qualified for small scale GPS network.     

石墨烯用于提高材料抗原子氧剥蚀性能

提出新型二维纳米材料石墨烯在航天器上的应用.首先采用超声空化法制备得到石墨烯,然后将其添加到环氧树脂中,采用共混法制成纳米复合材料.热失重分析显示材料的热稳定性能有所提高.在地面模拟设备中对环氧树脂和纳米复合材料进行了原子氧效应试验,并对试验前后材料的质量损失、表面形貌和表面成分等进行了分析,结果表明纳米复合材料相对于纯环氧树脂,其抗原子氧剥蚀性能有明显提高.