带防热层复合材料锥壳热固化变形的数值模拟

采用数值模拟方法研究带防热层缠绕成型复合材料锥壳热固化变形的形成机理和影响因素.建立了带防热层复合材料锥壳热固化变形预测的三维有限元程序.计算结果表明:外层防热材料和内层结构材料热膨胀系数不匹配是引起壳体固化变形的主要原因.提出在内层和外层之间增加中间过渡层的方法控制壳体的固化变形,中间层材料为丁腈橡胶片时可使固化变形减小20%以上.采用数值模拟方法讨论了中间层模量、厚度以及缠绕张力对壳体固化变形的影响,分析结果表明:固化变形随中间层模量的增加而增加,随中间层厚度的增加略有减小;缠绕张力释放增加壳体的固化变形,缠绕张力越大引起的固化变形越大.     

超磁致伸缩作动器的结构分析

从力学和磁学两方面分析了超磁致伸缩作动器内部结构形式对作动器特性的影响,重点研究了永磁铁式偏置磁场的不同结构形式以及作动器外壳材料对作动器的输出性能及作动器轴向刚度的影响.研究结果表明,环套式永磁铁的结构形式不可避免地在作动器外围产生较大磁场;分段式永磁铁的结构形式,采用钢制外壳时可避免漏磁;但是在芯棒区域的磁场与理想均匀磁场的差异将给作动器的输出位移带来较大损失,对作动器的刚度也会产生不可忽略的影响,二者在设计中必须考虑.在结构分析的同时,基于超磁致伸缩材料的特性提出了磁场与刚度相关联的设计理念,可为超磁致伸缩作动器的结构设计提供参考.     

Autonomous navigation of Mars probe using X-ray pulsars: Modeling and results

Autonomous navigation of Mars probe is a main challenge due to the lack of dense ground tracking network measurements. In this paper, autonomous navigation of the Mars probe Orbits is investigated using the X-ray pulsars. A group of X-ray pulsars with high ranging accuracy are selected based on their properties and an adaptive extended Kalman filter is developed to incorporate the Mars probe dynamics and pulsar-based ranging measurements. Results of numerical experiment show that the three-dimensional positioning accuracy can achieve 750m in X-axis, 220m in Y-axis and 230m in Z-axis, which is much better than the positioning results by current Very Long Baseline Interferometry (VLBI) or Doppler observations with the accuracy of 150 km or several kilometers, respectively.     

Powered-descent trajectory optimization scheme for Mars landing

This paper presents a trajectory optimization scheme for powered-descent phase of Mars landing with considerations of disturbance. Firstly, θ–D$\theta ''–''D$ method is applied to design a suboptimal control law with descent model in the absence of disturbance. Secondly, disturbance is estimated by disturbance observer, and the disturbance estimation is as feedforward compensation. Then, semi-global stability analysis of the composite controller consisting of the nonlinear suboptimal controller and the disturbance feedforward compensation is proposed. Finally, to verify the effectiveness of proposed control scheme, an application including relevant simulations on a Mars landing mission is demonstrated.     

基于四路信号处理的载波锁相环

载波跟踪环是独立导航接收机中最为脆弱的部分,在一定载噪比下,影响载波跟踪环跟踪门限的主要因素是动态应力。科斯塔斯锁相环是最常用的载波跟踪环之一,由于频率牵引范围的限制,其对动态应力非常敏感,该频率牵引范围由最大相位牵引范围决定。传统科斯塔斯锁相环是基于两路信号处理进行载波相位锁定的,其相位牵入范围仅为［-π/2,π/2］。文章提出了一种基于四路信号处理的科斯塔斯锁相环,增加的两路信号分别与原来两路相位相差π/4,其相位牵入范围可以达到［-3π/4,3π/4］,较传统方式提高了1/2。仿真结果显示文中提出的设计方法能够明显提高环路的动态性能     

负压式平板型环路热管试验

为解决高热流密度电子器件的散热问题,设计了一套负压式铜 甲醇环路热管,其蒸发器设计成平板型。研究表明,该平板型环路热管具有较高的散热能力,能够在无重力姿态和重力姿态下顺利启动。当重力倾角分别为0°、18°和30°,热负荷为160W时,蒸发器壁面温度分别达到85.8℃、66.3℃和64.6℃。按照环路热管启动状态,其启动过程可分为3个阶段：加热阶段、预启动阶段和后启动阶段。在低热负荷区域,环路热管会出现温度波动现象。增大重力倾角,有利于降低蒸发器壁面温度和热阻。当重力倾角为30°,热负荷从10W递增到160W时,环路热管的热阻从4.97℃/W降低到0.39℃/W。     

费用约束下含应力优化的CSADT设计

恒定应力加速退化试验(CSADT,Constant Stress Accelerated Degradation Testing)方案中需要确定的变量有应力水平、各应力下样本量、监测间隔和各应力下监测次数.如何对CSADT的应力水平进行优化目前很少有人探讨.针对这一问题提出一种在费用约束下将上述4个变量进行综合优化的方法.首先用随机过程描述CSADT下产品的性能退化过程,然后以产品在使用条件下p分位寿命可靠度的渐近方差最小为目标,以试验费用不超过预算为约束条件,给出CSADT的4个优化变量,并给出应用该优化方法的仿真算例.最后,优化方案对模型参数偏差的敏感性分析表明,在一定偏差范围内优化结果具有良好的稳健性.      

Geostationary orbit determination using SATRE

A new strategy of precise orbit determination (POD) for GEO (Geostationary Earth Orbit) satellite using SATRE (SAtellite Time and Ranging Equipment) is presented. Two observation modes are proposed and different channels of the same instruments are used to construct different observation modes, one mode receiving time signals from their own station and the other mode receiving time signals from each other for two stations called pairs of combined observations. Using data from such a tracking network in China, the results for both modes are compared. The precise orbit determination for the Sino-1 satellite using the data from 6 June 2005 to 13 June 2005 has been carried out in this work. The RMS (Root-Mean-Square) of observing residuals for 3-day solutions with the former mode is better than 9.1 cm. The RMS of observing residuals for 3-day solutions with the latter mode is better than 4.8 cm, much better than the former mode. Orbital overlapping (3-day orbit solution with 1-day orbit overlap) tests show that the RMS of the orbit difference for the former mode is 0.16 m in the radial direction, 0.53 m in the along-track direction, 0.97 m in the cross-track direction and 1.12 m in the 3-dimension position and the RMS of the orbit difference for the latter mode is 0.36 m in the radial direction, 0.89 m in the along-track direction, 1.18 m in the cross-track direction and 1.52 m in the 3-dimension position, almost the same as the former mode. All the experiments indicate that a meter-level accuracy of orbit determination for geostationary satellite is achievable.