弯曲壁面上离散孔气膜冷却均匀性的实验研究

本文利用传质比拟传热的方法,研究离散孔气膜冷却在整个弯曲壁面上沿与主流垂直方向的冷却均匀性。比较了单、双排孔和前、后排孔流量不等时,在不同吹风比的条件下,在凸、凹表面上冷却均匀性的特征。     

组合催化剂MT在丁羟推进剂中的应用

研究试验了组合催化剂MT在丁羟推进剂中提高燃速和降低燃透压强指数的作用。结果表明，MT与不同含量和粒度小于10μm的AP匹配使用，燃速可在9mm／s～30mm／s范围内调节；压强指数均小于0．2（压强范围3MPa～9MPa），出现“平台”燃烧效应；发动机实测的压强指数与试验结果基本一致；选用合理的M与T组合比，可不影响推进剂制造工艺性能和药柱力学性能。对结果的理论分析认为，M与T对改善AP低压下热分解具有协同效应。     

Parallel resonant converter with LLC-type commutation

It is shown that by using a proper transformation of state variables, the third-order system of the parallel resonant converter (PRC) with LLC-type commutation can be analyzed by means of a two-dimensional state-plane diagram. A set of characteristic curves which can be used for the converter design is derived from the analysis. It is shown from these curves that the converter possesses more desirable features than the conventional PRC     

细长体分离起始点的实验研究

本文实验研究了细长体模型在中等迎角下的初始分离问题。观察了不同头部形状的细长体在不同迎角下的分离流态。考察并分析了分离起始点的性质。观察到开式分离的存在,实验结果分析认为开式分离可以起始于正常点。此外,在钝头和尖头模型上都出现了螺旋点形式的头部涡。它们或是闭式分离的起始点,或是奇点型开式分离的起始点。     

单向玻璃纤维增强环氧树脂低温冲击拉伸性能的试验研究

 在经改进后配有低温装置的杆-杆型冲击拉伸装置上,对单向玻璃纤维增强环氧树脂在室温、-50℃、-100℃和-150℃的冲击性能进行了研究。结果表明该材料有温度相关性,所研制的装置性能良好,便于应用。     

Analysis and Design of Series Resonant Converter by State-Plane Diagram

Analysis based on the state-plane diagram is given for series resonant converters operating in the frequency range 0.5 ? fs/fo ? 1.0. When the voltages and currents in the converter are normalized, design parameters take on special geometric meanings in the normalized state diagram. Examples of converter design using graphical methods are given for the cases of ? and ? control. Control characteristics of the converter operating in the continuous conduction mode are derived. The concept of the energy reflection coefficient is introduced as a measure of power transfer efficiency in the converter design.     

一种新的二维最大熵图象阈值分割方法

根据最大熵原理提出了一种用二维最大熵获取二值图象的新方法，介绍了用梯度－区域灰度均值二维最大熵求取阈值的原理和过程。计算机仿真结果表明，采用本文提出的阈值分割方法，对于直方图平坦的灰度图象处理效果尤为理想。     

有效载荷／运载火箭耦合分析的频域方法

盘算尖响函数综合技术导出了用耦合频响函数和无有效载荷的运载火箭界面加速度响应表示的有效载荷／运载火箭耦合动力分析的频域方法，给出了以自由界面的运载火箭模态分数放自由界面或固定界面有效载荷模态参数构成的耦合频响函数表达式。     

结构优化中的混合变量应力约束近似方法

提出一种处理结构优化应力约束的新近似方法，以往一般直接对应力约束按设计变量近似，本文用近似内力间接近似应力约束以得到更高的近似质量，根据对内力和设计变量关系分析，提出了内力按混合变量一阶泰勒展开的高捏近似方法。近似优化问题用约束变尺度法求解，最后按出了几个典型例题。结果表明该方法简单，有效，可靠。     

Orientations of LASCO Halo CMEs and their connection to the flux rope structure of interplanetary CMEs

Coronal mass ejections (CMEs) observed near the Sun via LASCO coronographic imaging are the most important solar drivers of geomagnetic storms. ICMEs, their interplanetary, near-Earth counterparts, can be detected in situ, for example, by the Wind and ACE spacecraft. An ICME usually exhibits a complex structure that very often includes a magnetic cloud (MC). They can be commonly modelled as magnetic flux ropes and there is observational evidence to expect that the orientation of a halo CME elongation corresponds to the orientation of the flux rope. In this study, we compare orientations of elongated CME halos and the corresponding MCs, measured by Wind and ACE spacecraft. We characterize the MC structures by using the Grad–Shafranov reconstruction technique and three MC fitting methods to obtain their axis directions. The CME tilt angles and MC fitted axis angles were compared without taking into account handedness of the underlying flux rope field and the polarity of its axial field. We report that for about 64% of CME–MC events, we found a good correspondence between the orientation angles implying that for the majority of interplanetary ejecta their orientations do not change significantly (less than 45 deg rotation) while travelling from the Sun to the near-Earth environment.