排序方式: 共有98条查询结果,搜索用时 46 毫秒
71.
R0110重型燃气轮机DLN燃烧室NOx排放特性研究 总被引:1,自引:0,他引:1
R0110重型燃气轮机燃烧室按干式低污染(DLN)原理设计,采用径向燃料分级燃烧技术,具有两种燃烧模式。为检验燃烧室的NOx排放特性,在低压模拟条件下,对模式Ⅰ和模式Ⅱ分别进行了燃烧室单管试验。结果表明,模式Ⅱ的NOx排放比模式Ⅰ显著降低,但还未能完全满足设计要求。为此,对燃烧室结构、燃料分配特性及模式Ⅱ的工作过程进行了详细分析,提出了进一步改善燃烧室NOx排放特性的措施和建议。 相似文献
72.
73.
74.
机载雷达综合显示器的仿真实现 总被引:1,自引:0,他引:1
雷达综合显示器是一种能够灵活地把雷达一次信息、二次信息、地图背景和各种表格数据综合在同一个显示界面进行显示的雷达终端系统,可以形象地提供雷达威力范围内比较全面的综合信息。本文对应用Visual C++程序设计来实现航空机载雷达综合显示器的仿真问题进行了探讨。 相似文献
75.
With the continuous growth of air traffic flow, some airports in China or other countries begin to construct Closely Spaced Parallel Runways (CSPR) to meet the capacity requirement of civil aviation. In this paper, the simulation and calculation method of flight trajectory is developed, as well as the collision risk calculation method and wake vortex encounter risk calculation method. New methods for departure and go-around procedures are proposed to achieve approximate segregated parallel operation in an attempt to obtain approximately the same results on closely spaced parallel runways as on widely spaced parallel runways. By comparing with the independent parallel departure and segregated parallel operation in ICAO Doc. 9643, it is found that the lateral separation between aircraft in this proposal is not less than the separations in the other two cases. Based on the simulation calculation of flight trajectories under different conditions, the probabilities of collision conflict and encountering wake vortex are lower than those in current operation plan. The proposed plan has no special requirements in pilot operation, control command procedures, airport facilities, or meteorological observation and prediction, so it is convenient to promote and implement at the airports with closely spaced parallel runways. 相似文献
76.
为了研究大飞机坠撞特性及数值分析方法,选取大飞机货舱地板下部结构为研究对象,建立其有限元模型,实现显式动力学的求解与分析。考察倒置、固支的货舱地板下部结构在200 kg落重以7 m/s垂直冲击下的结构响应、吸能与失效的动态行为,识别落重冲击过程中结构变形与失效模式、冲击响应特性及能量吸收与耗散机理。仿真结果表明,货舱地板下部结构的机身框组件、支撑件组件是主要吸能结构,冲击能量的吸收主要依靠上述结构的塑性变形与失效,紧固件的吸能贡献仅占1%左右。 相似文献
77.
78.
79.
在电机高速弱磁或过载要求高的情况下,需要通过脉冲宽度调制(PWM)的过调制运行提高直流母线电压利用率。基于磁链观测的无传感器永磁同步电机矢量控制(磁场导向控制,FOC)技术具有算法简单、易实现等优点,但在过调制的情况下电压限幅环节会引起磁链观测及转子位置角估算误差。为提高PWM过调制情况下系统的控制性能,对传统的FOC控制框图进行了改进,省去了电压限幅环节并利用由占空比计算的实际电压对定子磁链进行估算。MATLAB仿真验证了改进方法的有效性。研究结果表明:该方法充分利用PWM调制自有的限幅特性,既能简化控制算法又能提高磁链观测精度,具有较好的技术经济性能。 相似文献
80.
随着风力机的发展越来越智能化,除了要求风力机的运行可靠性,还要求其有稳定的输出功率。为了使风力机变桨控制器在运行过程中具有优良的动态品质,提出了一种自抗扰控制(ADRC)的变桨距控制方案,但ADRC也存在参数多、整定难度大这一明显缺点。为此,将教与学算法应用到ADRC的整定过程中,实现了参数的自动整定。仿真结果验证了通过教与学算法自动整定ADRC参数的可行性,与传统PID控制器相比,整定后的ADRC能较好地满足风力机变桨距控制要求,有效维持了风力机输出功率的稳定性。 相似文献