Influence of disturbances on the angular motion of a spacecraft in the powered section of its descent

The motion of a variable-mass spacecraft is considered in the powered section of a descending trajectory. Approximate analytical solutions are obtained for the angles of spatial orientation of the spacecraft, which allows one to analyze the nutation motion and to develop recommendations on the spacecraft’s mass configuration, providing the smallest possible deviations of the longitudinal axis and thrust vector from specified directions. The errors of stabilization of the spacecraft’s longitudinal axis are calculated by means of numerical integration of complete models and using the obtained analytical solutions, the results being in good agreement.     

Ray Based Diffraction Tomography of the Ionosphere and Laboratory Inhomogeneous Plasma

A new procedure for restoration of the plasma inhomogeneities with improved resolution is suggested. The procedure deals with the double weighted Fourier transform (DWFT) of the observed wavefield in coordinates of both receivers = (x, y) and sources ₀ = (x ₀, y ₀) [1]. Phase increments between the sources and receivers, being found from DWFT representation, can be used for extracting information on small perturbations of the dielectric constant ~(, z) in a way similar to traditional radio tomography. The resulting resolution of the method is close to the diffraction limit = h/D in the horizontal direction and z = (h/D)² in the vertical direction, where h is the height of inhomogeneities and D is the length of the ground-based receiving system.     

固体发动机喷管延伸锥展开前级间分离的热环境分析

通过FLUENT流场计算软件,采用RNGK k-ε湍流模型,针对带有延伸喷管的多级固体发动机级间热分离的热环境进行了数值分析。研究表明,延伸喷管尾流受到连接筒、前封头、延伸段的阻碍后,其流动特征变化显著,尤其在一级前封头的影响下形成回流,并在喷管内形成激波。计算得到的热环境参数,对发动机的热防护设计具有一定的参考价值。     

化学气相反应法在C/C复合材料抗氧化处理中的应用

通过把硅蒸气渗入预制体孔隙与碳直接反应生成SiC的化学气相反应(CVR)方法,提高初始密度和预制体结构均不同的C／C复合材料的抗氧化能力,研究了C／C复合材料的密度变化与微观结构,并对其进行了氧化试验。结果表明,因CVR温度、C／C复合材料初始密度不同,抗氧化处理后的密度增加量有显著不同。针刺炭布C／C／SiC复合材料在马福炉中于1160℃经65min氧化后,其失重率仅2．6％,而密度为1．95g／cm^3的同结构C／C复合材料相在同条件下失重率高达32％。     

Bubble detector characterization for space radiation

In light of the importance of the neutron contribution to the dose equivalent received by space workers in the near-Earth radiation environment, there is an increasing need for a personal dosimeter that is passive in nature and able to respond to this neutron field in real time. Recent Canadian technology has led to the development of a bubble detector, which is sensitive to neutrons, but insensitive to low linear energy transfer (LET) radiation. By changing the composition of the bubble detector fluid (or “superheat”), the detectors can be fabricated to respond to different types of radiation. This paper describes a preliminary ground-based research effort to better characterize the bubble detectors of different compositions at various charged-particle accelerator facilities, which are capable of simulating the space radiation field.     

Odyssey: Principles for enduring space exploration

As the USA, Europe and other nations embark on a new voyage of exploration to the Moon, Mars and beyond, they should lay the foundations and establish precedents that invite a host of participants and followers. We argue that international cooperation, driven by foreign-policy and cost-sharing considerations, has taken a prominent role but must be pragmatically and flexibly balanced with economic and strategic self-interest. Since exploration visions are likely to differ, the steps each country will pursue, the funding provided, and schedules followed will also differ. To support an enduring exploration vision, it will be important to remain flexible to changing priorities and amenable to the inclusion of new, non-traditional participants. Open-systems principles and metaprinciples should be employed at all levels—hardware, software, programmatic, political and cultural. Equally important, national leadership and decision makers should be mindful of the potential pitfalls that might undermine the venture. While the new vision inspires us all, it will take creativity, resourcefulness, hard work and cooperation to succeed.     

Ground based ISS payload microgravity disturbance assessments

In order to verify that the International Space Station (ISS) payload facility racks do not disturb the microgravity environment of neighboring facility racks and that the facility science operations are not compromised, a testing and analytical verification process must be followed. Currently no facility racks have taken this process from start to finish. The authors are participants in implementing this process for the NASA Glenn Research Center (GRC) Fluids and Combustion Facility (FCF). To address the testing part of the verification process, the Microgravity Emissions Laboratory (MEL) was developed at GRC. The MEL is a 6 degree of freedom inertial measurement system capable of characterizing inertial response forces (emissions) of components, sub-rack payloads, or rack-level payloads down to 10(-7) g's. The inertial force output data, generated from the steady state or transient operations of the test articles, are utilized in analytical simulations to predict the on-orbit vibratory environment at specific science or rack interface locations. Once the facility payload rack and disturbers are properly modeled an assessment can be made as to whether required microgravity levels are achieved. The modeling is utilized to develop microgravity predictions which lead to the development of microgravity sensitive ISS experiment operations once on-orbit. The on-orbit measurements will be verified by use of the NASA GRC Space Acceleration Measurement System (SAMS). The major topics to be addressed in this paper are: (1) Microgravity Requirements, (2) Microgravity Disturbers, (3) MEL Testing, (4) Disturbance Control, (5) Microgravity Control Process, and (6) On-Orbit Predictions and Verification.     

Three dimensional temperature field in a conducting sphere due to an arbitrarily located split ring heating source

Thermal control of spacecrafts plays an important role in space missions. In the design stage the preliminary thermal analysis of the spacecraft requires an estimate of the conductive thermal resistance between the various spacecraft components. With this in mind, the fully three dimensional problem of determining the thermal field in a conducting sphere with an asymmetric split ring current carrying heating source is resolved in an analytical or almost analytical form, implying either a closed form solution or utmost expressions involving a simple numerical integration. This has immediate application for evaluation of thermal resistance in spacecrafts. Green's function integral techniques are used. Comparisons are made with series solutions and also with purely numerical solutions to contrast the simplicity and highlight the elegance of the present method. Parametric studies reveal expected behavior.     

Behavior of tethered debris with flexible appendages

Active exploration of the space leads to growth of a near-Earth space pollution. The frequency of the registered collisions of space debris with functional satellites highly increased during last 10 years. As a rule a large space debris can be observed from the Earth and catalogued, then it is possible to avoid collision with the active spacecraft. However every large debris is a potential source of a numerous small debris particles. To reduce debris population in the near Earth space the large debris should be removed from working orbits. The active debris removal technique is considered that intend to use a tethered orbital transfer vehicle, or a space tug attached by a tether to the space debris. This paper focuses on the dynamics of the space debris with flexible appendages. Mathematical model of the system is derived using the Lagrange formalism. Several numerical examples are presented to illustrate the mutual influence of the oscillations of flexible appendages and the oscillations of a tether. It is shown that flexible appendages can have a significant influence on the attitude motion of the space debris and the safety of the transportation process.