钛合金TB6铣削加工硬化实验

研究了使用涂层硬质合金刀具对钛合金TB6进行端铣加工时,铣削参数以及刀具后刀面磨损量对加工硬化（表面硬化率、硬化层深度以及硬化层硬度分布）的影响,以弄清TB6铣削硬化现象及机理.结果表明,在实验参数范围内,刀具无磨损的情况下,硬化率基本保持在107%~112%范围内,硬化层深度范围为18~36 μm;铣削速度增加时,加工硬化程度会有较为明显的降低现象,而进给量与切深对加工硬化的影响并不明显;刀具磨损对加工硬化的影响较为显著,后刀面磨损量低于0.2 mm时,硬化层深度随着磨损增加从30 μm增加至55 μm,而后刀面磨损量为0.35 mm时,硬化层深度达到了130 μm.刀具磨损后在加工表面下较浅位置出现软化区域,而且随着磨损量的增加,软化越来越明显.      

Estimation of GPS instrumental biases from small scale network

With 4 GPS receivers located in the equatorial anomaly region in southeast China, this paper proposes a grid-based algorithm to determine the GPS satellites and receivers biases, and at the same time to derive the total electron content (TEC) with time resolution of 15 min and spatial resolution of 1° by 3.5° in latitude and longitude. By assuming that the TEC is identical at any point within a given grid block and the biases do not vary within a day, the algorithm arranges unknown biases and TECs with slant path TEC from the 4 receivers’ observations into a set of equations. Then the instrumental biases and the TECs are determined by using the least squares fitting technique. The performance of the method is examined by applying it to the GPS receiver chain observations selected from 16 geomagnetically quiet days in four seasons of 2006. It is found that the fitting agrees with the data very well, with goodness of fit ranging from 0.452 TECU to 1.914 TECU. Having a mean of 0.9 ns, the standard deviations for most of the GPS satellite biases are less than 1.0 ns for the 16 days. The GPS receiver biases are more stable than that of the GPS satellites. The standard deviation in the 4 receiver bias is from 0.370 ns to 0.855 ns, with a mean of 0.5 ns. Moreover, the instrumental biases are highly correlated with those derived from CODE and JPL with independent methods. The typical precision of the derived TEC is 5 TECU by a conservative estimation. These results indicate that the proposed algorithm is valid and qualified for small scale GPS network.     

分离式机械压汽蒸馏系统的实验

针对传统机械压汽蒸馏的不足,提出分离式机械压汽蒸馏系统.建立了一套容量为1.5 m3/d的单效分离式机械压汽蒸馏系统并对其进行实验研究.实验系统主要由两套旋转蒸发器、冷凝器以及压缩机组成.通过改变压缩机转速和蒸发温度来研究系统的性能.结果表明在蒸馏水产量一定的前提下压缩机进口压力和冷凝器进口压力随着压缩机转速的增加而逐渐下降,换热温差随着压缩机转速的增加而增加,最高温差稳定在8.5℃左右.通过改变系统的真空度获得不同的蒸发温度,蒸发温度越高,蒸馏产量越高,系统性能也越好.      

Capillary flow rate limitation in asymmetry open channel

This paper focuses on the stability of capillary forced flow.In space,open capillary channels are widely used as the liquid and gas separation devices to manage liquid positioning and transportation.Surface collapse happens when the flow rate exceeds the critical value,leading to a failure of propellant management.Knowledge of flow rate limitation is of great significance in design and optimization of propellant management devices(PMDs).However,the capillary flow rate limitation in an asymmetry channel has not been studied yet in the literature.In this paper,by introducing an equivalent angle to convert the asymmetry corner to a symmetry one,the one-dimensional theoretical model is developed.The flow rate limitation can then be investigated as a function of the channel geometry as well as liquid property based on the model.Comparisons between the asymmetry and symmetry channels bring forth the characteristics of the two kinds of channels,and demonstrate good accordance between the new advanced model and the existing one in the literature.This theoretical model can provide valuable reference for PMD designers.     

开关磁阻调速电动机非线性分析

开关磁阴电机系统是性能优良的新型调速电动机系统。本文阐述了双凸极磁阻电机的非线性二维磁场的数值计算方法,据此进行了系统主电路的非线性网络数字分析,进而作了不同工作条件下的电流波形仿真、系统性能计算及控制参数的优化选择,初步实现了开关磁阻调速电动机系统的计算机辅助分析。并通过所研制的500W样机的具体计算和试验验证,证明计算和实测结果是吻合的。     

关于工业机器人运动学反问题的两种解法

本文发展了求解工业机器人运动学反问题的两种新方法:几何法和迭代法,分别适用于可解和不可解工业机器人的工作空间综合。     

平方阻尼在非线性缓冲系统中的作用

本文讨论平方阻尼(以参数a表征)在图(1)所示的缓冲系统中的作用,结果表明:平方阻尼对于降低相对位移峰值d_m总有良好的效果,但不一定降低加速度峰值a_m。在一定速度冲击V下,系统的平方阻尼有两种最佳值,使a_m最小的a_(am)和使缓冲效率γ最高的a_(cm),而平方阻尼最佳条件依赖于系统的缓冲弹簧的刚度变化类型: (1)线性弹簧情况:a_(am)=a_(cm),最佳条件为系统在首程中均匀减速; (2)渐硬弹簧情况:a_(am)=a_(cm),最佳条件为系统在首程中初始和终末加速度相等即; aV~2=ω_0~2q(dm) (3)渐软弹簧情况:a_(cm)>a_(am)。 本文的基础是所谓“首程显峰”,假定即系统在速度冲击V下的响应峰值d_m和a_m出现在第一行程中。当平方阻尼值不太小,缓冲弹簧刚度特性接近反对称时,该假定成立。     

气动系数插值在捕获轨迹试验中的应用

本文叙述气动系数插值在捕获轨迹试验中的交叉核对和轨迹计算中的应用。对外挂物在某一个新的位置上的某些量的误差进行核对,看其是否在允许的范围之内,称为“交叉核对”。交叉核对分为两种,一种是对位置本身的核对,另一种是对气动系数的核对。在轨迹计算的每一个步长中应用气动系数插值,可以使计算更加精细,轨迹更加光滑。本文对气动系数插值作了一些改进的尝试,提出将气动系数对时间的插值改为气动系数对线位移的插值,这仅是初步的尝试,有待进一步探索。