虚拟仪器在频率参数计量测试中的应用

介绍了虚拟仪器及其驱动程序，在ＬａｂＶＩＥＷ图形编程环境下所编制的检定分数频率的虚拟仪器驱动软件。     

Ku波段波导扫频双六端口网络分析仪

介绍研制的一种实用Ku波段扫频双六端口网络分析仪。该仪器能同时测量双口网络的4个散射参数及单口网络的复反射系数。     

环路热管内工质流动特性的研究

由于环路热管（LHP）具有高传热性能、远距离传输热量、优良的控温特性和管路的可任意弯曲、安装方便等特点，使LHP在航天热控领域有着广泛的应用前景。文章对LHP内工质的流动压力降进行了分析和计算；对毛细芯所能提供的最大蒸发传热能力进行了预测，并结合实验研究综合分析了毛细芯结构对LHP性能的影响。     

化学物质释放人工改变电离层

考虑中性气体在电离层高度的扩散过程和相应的电离层离子化学过程，研究了利用主动化学物质释放来改变电离层的方法，理论计算了H2O和SF6两种气体释放后电离层随时间的响应过程，结果表明，在电离层高度上气体的扩散过程非常迅速，电离层F区的电子密度有很大程度的减少，而扩散慢且化学反应快的气体对电离层的影响更大，就更加有利于电离层洞的形成。     

直升机“地面共振”力学模型的探讨

 <正> I_B 桨叶绕垂直铰的转动惯量I_(?),I_(?),I_(?) 机身绕过其重心O的x,y,z 轴的转动惯量ι 桨叶长度m_B 单片桨叶的质量     

基于层次分析法的飞行模拟训练评价体系设计

为科学完善地描述飞行模拟训练中的应急处置程序,提升飞行员专业驾驶技术水平,本文提出飞行模拟训练评价体系,并通过层次分析法构造3阶判断矩阵,检测矩阵一致性指标为0.037,具有可接受性;并采用关联度进行数据分析量化计算,为飞行训练考核标准奠定理论基础。     

磁选态单束铯束管束光学参数的模拟计算和设计

为提高铯束管跃迁信号强度,在束光学参数设计中,用蒙特卡罗方法模拟计算铯原子通过率和未跃迁比例。通过改变模拟计算中的束光学参数,分析铯原子通过率、未跃迁比例和倍增器首极电流的变化趋势,得到了主要束光学参数的合理取值范围。在铯束管实际装配和试验中使用束光学参数设计结果,有效地增加了倍增器首极电流。     

火箭橇体进水现象研究

在考核过载承受能力的火箭橇试验后,橇体内发现有水,从空气动力学的角度,对火箭橇体进水现象进行了初步分析,并利用FLUENT软件对进水原因进行了初步研究,通过分析,发现结构在穿越跨音速阶段时,由于内外压差的变化将导致内部或外部产生水汽。该发现为结构设计提供有益的建议。     

Fault Estimation and Accommodation for a Class of Nonlinear System Based on Neural Network Observer

The problem of fault estimation and accommodation of nonlinear systems with disturbances is studied using adaptive observer and neural network techniques.A robust adaptive learning algorithm based on switchingβsmodification is developed to realize the accurate and fast estimation of unknown actuator faults or component faults.Then a fault tolerant controller is designed to restore system performance.Dynamic error convergence and system stability can be guaranteed by Lyapunov stability theory.Finally,simulation results of quadrotor helicopter attitude systems are presented to illustrate the efficiency of the proposed techniques.     

A surface parametric control and global optimization method for axial flow compressor blades

An aerodynamic optimization method for axial flow compressor blades available for engineering is developed in this paper. Bezier surface is adopted as parameterization method to control the suction surface of the blades, which brings the following advantages:(A) significantly reducing design variables;(B) easy to ensure the mechanical strength of rotating blades;(C) better physical understanding;(D) easy to achieve smooth surface. The Improved Artificial Bee Colony(IABC) algorithm, which significantly increases the convergence speed and global optimization ability, is adopted to find the optimal result. A new engineering optimization tool is constructed by combining the surface parametric control method, the IABC algorithm, with a verified Computational Fluid Dynamics(CFD) simulation method, and it has been successfully applied in the aerodynamic optimization for a single-row transonic rotor(Rotor 37) and a single-stage transonic axialflow compressor(Stage 35). With the constraint that the relative change in the flow rate is less than0.5% and the total pressure ratio does not decrease, within the acceptable time in engineering, the adiabatic efficiency of Rotor 37 at design point increases by 1.02%, while its surge margin 0.84%,and the adiabatic efficiency of Stage 35 0.54%, while its surge margin 1.11% after optimization, to verify the effectiveness and potential in engineering of this new tool for optimization of axial compressor blade.