基于STM32F429的全向运动平台的运动控制

全向运动平台系统是可以实现人体在各个方位行走的2D运动平台。针对实现人体在全向运动平台稳定行走的运动控制,采用加入观测器的一阶控制算法对平台运动控制进行探究。先通过MATLAB软件进行算法的仿真,验证方法的可行性;再通过现场测试,验证控制算法的有效性。最终试验表明,加入观测器的一阶控制算法可对全向运动平台实现有效的运动控制。此运动控制策略的探究为全向运动平台的运动控制提供了一种可行的控制思路和方案。     

Containment of soft wall casing wrapped with Kevlar fabric

Aramid fabrics have been commonly used in the civil turbofan engine fan blade containment system for its excellent performance. To investigate the behavior and capability of soft wall containment casing, a series of fan blade released tests were conducted on the high-speed spin tester.The soft wall casing was fabricated by wrapping multiple layers of Kevlar49 plain woven fabric around a thin steel ring. Casings with different inner metal ring and outer fabric layers number were compared. The method of using the explicit dynamic software LS-DYNA to establish the finite element analysis model for the quantitative analysis of the containment process was developed and conducted. The simulation results are in good agreement with the test results. It is shown that the containment process of the soft wall casing can be divided into three impact stages. The casing with low-stiffness inner metal ring will get severe overall deformation and lose the structural integrity when it suffers the blade impact. Kevlar fabric layers will appear large bulge on outside surface and absorb the most impact dynamic energy of the high speed released fan blade. By summing up the results of the test and simulation, an empirical critical equation was derived to describe the relationship between the released blade dynamic energy and the Kevlar fabric thickness.     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

真实气体效应对Ma10级进气道流动的影响

为了探究高马赫数超燃冲压发动机高速飞行时真实气体效应对进气道流场的影响,仿真获得了不同气体模型下Ma10级进气道流场结构和性能。结果表明:进气道主流流场温度较低,不足以触发空气的离解反应,反应仅发生在边界层内,但反应程度较低,远未达到化学平衡状态,除了边界层温度及热载荷特性,其流场结果则更为贴近冻结流流场,因而化学非平衡模型与热完全气体模型的进气道通流流场结构和性能基本一致。而真实气体效应导致边界层特性的不同,对进气道起动特性产生影响,吸热离解反应通过对进口分离包的抑制和增大进口马赫数将进气道的再起动马赫数从9.8降低到9.4。在对进气道在宽速域应用中的钝化设计研究发现,真实气体效应虽然对前缘钝化进气道流场的压力分布和性能无明显影响,但是其能起到整体降低壁面热流的作用,不仅钝头处的热流降低了1MW/m2,通道内的热流也整体降低了0.1MW/m2。     

低排放燃烧室NO_x排放试验及预测方法研究

为了研究中心分级贫油低排放燃烧室的排放特性和排放预测方法,针对一个低排放头部方案,在单头部燃烧室试验件上,在不同的温度、压力、油气比、供油模式和分级比条件下,测量其排放性能。以Lefebvre排放经验预测公式为基础,采用经验分析方法拟合排放试验数据,归纳出适用于本头部方案的排放预测公式。表征预测好坏的判定系数R2在小工况下和大工况下分别为0.95和0.93,表明预测结果与试验结果符合度较好。小工况和大工况排放特性不同,对仅预燃级喷油的小工况工作模式,NO_x排放主要受化学恰当燃烧温度和预燃级局部当量比的影响;对预燃级和主燃级同时喷油的大工况工作模式,NO_x排放主要受燃烧区温度和主燃级燃油比例的影响。     

风洞试验绳牵引冗余并联机器人的刚度增强与运动控制

 以一种应用于低速风洞试验的6自由度绳牵引冗余并联机器人为研究对象,解决飞行器模型在风荷作用下动态定位误差大、力学测量精度不高的问题。运用微分变换推导了该机器人的刚度解析表达式;分别建立了末端执行器和驱动系统的动力学模型;针对系统冗余驱动、强耦合和非线性的特点,设计了基于刚度增强准则的关节空间比例微分（PD）修正前馈控制器,实现了以提高飞行器升力方向、顺风向和俯仰转动方向刚度为目标的绳系张力优化分配。数值仿真算例表明,与基于张力极小准则的控制器相比,前者有效地提高了飞行器的动态定位精度。     

激光熔化沉积Ti-6Al-2Zr-Mo-V钛合金组织特征研究

采用激光熔化沉积快速制造工艺直接成形Ti-6Al-2Zr—Mo—V合金板材。激光熔化沉积过程中合金粉末充分熔化并在液态均匀混合以得到成分均匀、全致密的组织。SEM分析表明,激光沉积Ti-6Al-2Zr-Mo—V合金具有均匀细小的α／β双相片层组织,且片层取向随机多样,分布均匀。其组织特点与激光沉积过程中的快速凝固和固态相变有关。解释了其特征组织的形成机理,并讨论了其沉积层组织特征对性能的影响。     

窄带信号小样本谱估计算法

针对窄带平稳随机信号的小样本谱估计问题,结合均匀线性阵列的空间谱估计算法,提出了一种高性能小样本谱估计算法。该算法首先利用采样数据构造一个Toeplitz矩阵;然后对该矩阵进行特征值分解得到信号子空间和噪声子空间;再结合MUSIC、ESPRIT等子空间算法,即可实现对小样本采样数据的谱估计。数值仿真验证了该算法的有效性。     

某燃气涡轮工作叶片裂纹分析

为阐明测试单元环境下加速任务试车(AMT)过程中叶片早期起裂的物理原因,对裂纹叶片断口进行了检查和分析,并采用LPTi's XactLIFETM系统对叶片进行了深入的分析.结果表明:叶片叶型发生了过量的蠕变损伤,此过量的蠕变损伤导致了叶片的过量延伸以及叶型特别是在尾缘区域的转扭,此行为可能造成AMT疲劳循环条件下缘板以下的叶片伸根部位疲劳裂纹的形核与生长.因此,过量的蠕变被认为是整个裂纹形核过程的主要驱动力.      

单晶合金蠕变性能影响因素分析

通过分析热处理工艺、元素含量、晶体取向性以及温度和应力对蠕变性能的影响,得出任何1种影响合金蠕变性能的因素其实质都是改变了合金的微观组织,并最终反映到γ′筏形的完善程度S、终端密度TD和线性密度LD上。S值越接近1,γ′筏形的完善程度越好,蠕变寿命就越长;而TD和LD值越大,微观组织图内筏形交叉和中断的数目就越多,蠕变寿命就越短。