神舟2号大气密度探测器的探测结果(Ⅰ)日照和阴影区域热层大气密度变化

选用了神舟2号（SZ-2）大气密度探测器在2001年2—4月间的探测数据,进行日照和阴影区域热层大气密度变化的探讨.结果表明:在高度410km附近,日照和阴影区域大气密度变幅为2—3倍,变幅的大小与地磁活动程度呈负相关关系.日照面大气密度峰区位于星下点地方时1400—1500LT的纬度处,峰值大小与太阳活动程度呈正相关关系.阴影面大气密度谷区位于星下点地方时0400-0500的纬度处,同时在±10°纬度区域中还出现了阴影面峰区.     

钛合金胶接点焊接头的性能检测

研究了不同焊接电流下钛合金板胶接点焊接头的A扫描信号和C扫描图像特征,并进行了拉伸-剪切试验。结果表明:通过观察C扫描图像的特征与A扫描信号的变化,能够划分胶接点焊接头的胶层区、热影响区、熔合区、熔核区以及焊接缺陷;随着电流(7~10 k A)的逐渐增大,接头熔核直径呈递增趋势,相应的失效载荷从7 231.5增加到10 939.0 N;当电流为7 k A时,在C扫描图像上反映出飞溅缺陷,此时接头失效载荷远小于没有出现飞溅的接头,可见飞溅降低了胶接点焊接头的拉剪载荷。     

湿度传感器能力验证活动误差来源分析

本文主要阐述了本实验室在参加由CNAS组织的湿度传感器能力验证活动中,当最终结果报告中出现临界值情况时,应采取的措施:包括分析误差的主要来源,制定相应的纠正措施,并验证结果的过程。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

基于STM32的视频流图像更新方法的研究

对基于STM32系统低速(工作主频72MHz)视频流处理显示更新方案的研究。结合图像处理基本理论,分析传统的显示方法的不足,并提出一种新的视频流图像更新的方法,通过一定的实验数据和理论结果,验证该方法可行性。     

LENS风洞试验返回器模型气动热特性模拟

国家数值风洞高超声速流动模拟软件HyFLOW的研制对打破国外同类软件的技术壁垒具有重要意义。与国外DPLR软件进行了对比研究，同时系统介绍了HyFLOW软件求解器的数值方法、物理化学模型以及壁面催化特性计算模型等主要方法，采用典型算例对有限催化模型进行了数值验证，最后基于LENS风洞试验146 mm返回器标模外形开展了高超声速气动热特性数值模拟。研究结果表明，HyFLOW软件在高超声速热化学非平衡流动模拟与评估方面的气动力计算精度高，与国外同类软件DPLR相当，同时其壁面催化条件下的气动热计算精度可靠，可信度高。     

ENERGY-SAVING MATCHING STRATEGY AND EXPERIMENTAL STUDY OF PUMPING SYSTEM FOR TRUCK-MOUNTED CONCRETE PUMP

Aiming at the high fuel consumption and use-cost of truck-mounted concrete pump , an energy-saving matching strategy of pumping system is presented and the experimental study is conducted.Since pumping system occupies most resources of engine , the matching strategy between engine and main pump is analyzed to meet the load demand and reduce the engine rational speed drop.The testing method is established to measure the fuel consumption of engine under various working conditions , and the experimental data are analyzed to find the law of the fuel consumption of engine.The system performance can be improved by adjusting the system input value.Finally , the energy-saving matching strategy is established to reduce the fuel consumption of truck for unit workload , which provides a new approach for the energy-saving of truck-mounted concrete pump.     

基于有限元仿真的指尖密封准动态性能分析方法

指尖密封性能的量化表达和计算效率一直是设计人员关心的问题。针对指尖密封的工作特点,对其泄漏机理和磨损特性进行了分析。基于有限元分析构建了指尖密封性能量化表达的准动态性能模型,解决了理论设计中磨损和泄漏特性难以计算和计算工作量较大的问题。采用该方法的研究结果表明环境温度升高到300℃时,泄漏率较之27oC条件下降低了65%,磨损率升高了约4%;指尖片厚度从0.1mm增加到0.5mm时,泄漏率降低了70%,磨损率升高了28%;同时指尖曲梁个数、转子转速和压差对指尖密封性能同样具有重要影响。分析初步表明,提出的计算方法能够较好地反映指尖密封实际动态特性,为指尖密封性能设计提供了快捷高效计算方法。     

翼吊发动机安装结构等效建模及其隔振设计

为了研究翼吊发动机安装结构隔振特性并优化其隔振器设计,建立了发动机安装节-吊架-机翼结构理论分析及有限元模型.利用有限元方法进行了模态验证并分析了安装结构的隔振特性.进行发动机3种典型工况下的结构动响应分析确定了振动传递的主路径.基于振动传递路径法研究了隔振器参数和安装位置对安装系统隔振性能的影响规律.结果表明:振动载荷经安装结构后低压转子转频和高压转子转频峰值响应分别降低22.03%和14.65%.低压转子转频振动传递主路径为发动机-前安装节-吊架-机翼,高压转子转频为发动机-后安装节-上连杆-机翼.通过合理设置隔振器位置可以使安装系统隔振率达到50.41%,隔振器的频率比为5和阻尼比为0.25时安装系统隔振率可达70.67%.为了优化整个发动机安装系统的隔振效果,设计隔振器时必须选取合适的安装位置和参数.