Synthetic aperture radar capabilities for snow and glacier monitoring

The potential of SAR systems for monitoring the seasonal snow cover and glaciers has been investigated based on an airborne experiment in the Austrian Alps and on Seasat SAR and Shuttle Imaging Radar-A data. X- and C-band SAR are useful sensors for mapping wet snow packs, while in L-band snow-covered and snow-free surfaces often cannot be separated. SAR data in all three frequency bands provide valuable glaciological information.     

Land mobile satellite propagation experiments in Kyoto City

In February of 1990, land mobile satellite propagation experiments were conducted in Kyoto City, Japan, using the Engineering Test Satellite V (ETS-V). The signal transmitted from the satellite was received and recorded at a mobile unit moving in different streets of the downtown area. The streets chosen have typical downtown medium and high rise buildings, electric utility poles, trees, etc., which caused obstruction to the satellite line of sight. The propagation characteristics such as fade/nonfade distribution, joint fade and nonfade distribution, phase distribution, and their dependence on the antenna type are discussed for the measured link. Error characteristics in digital communication for the above link have been qualitatively analyzed on the basis of the measured signal level fluctuation. Effect of interleaving and coding to improve the communication link is also discussed     

Low energy ions in the heavy ions in space (HIIS) experiment on LDEF.

We present data from the Lexan top stacks in the Heavy Ions In Space (HIIS) experiment which was flown for six years (April 1984-Jan 1990) onboard the LDEF spacecraft in 28.5 degrees orbit at about 476 km altitude. HIIS was built of passive (i.e. no timing resolution) plastic track detectors which collected particles continuously over the entire mission. In this paper we present data on low energy heavy ions (10 < or = Z, 20MeV/nuc < E < 200 MeV/nuc). These ions are far below the geomagnetic cutoff for fully ionized ions in the LDEF orbit even after taking into account the severe cutoff suppression caused by occasional large geomagnetic storms during the LDEF mission. Our preliminary results indicate an unusual elemental composition of trapped particles in the inner magnetosphere during the LDEF mission, including both trapped anomalous cosmic ray species (Ne, Ar) and other elements (such as Mg and Fe) which are not found in the anomalous component of cosmic rays. The origin of the non-anomalous species is not understood, but they may be associated with the solar energetic particle events and geomagnetic disturbances of 1989.     

Regolith X-Ray Imaging Spectrometer (REXIS) Aboard the OSIRIS-REx Asteroid Sample Return Mission

The Regolith X-ray Imaging Spectrometer (REXIS) is the student collaboration experiment proposed and built by an MIT-Harvard team, launched aboard NASA’s OSIRIS-REx asteroid sample return mission. REXIS complements the scientific investigations of other OSIRIS-REx instruments by determining the relative abundances of key elements present on the asteroid’s surface by measuring the X-ray fluorescence spectrum (stimulated by the natural solar X-ray flux) over the range of energies 0.5 to 7 keV. REXIS consists of two components: a main imaging spectrometer with a coded aperture mask and a separate solar X-ray monitor to account for the Sun’s variability. In addition to element abundance ratios (relative to Si) pinpointing the asteroid’s most likely meteorite association, REXIS also maps elemental abundance variability across the asteroid’s surface using the asteroid’s rotation as well as the spacecraft’s orbital motion. Image reconstruction at the highest resolution is facilitated by the coded aperture mask. Through this operation, REXIS will be the first application of X-ray coded aperture imaging to planetary surface mapping, making this student-built instrument a pathfinder toward future planetary exploration. To date, 60 students at the undergraduate and graduate levels have been involved with the REXIS project, with the hands-on experience translating to a dozen Master’s and Ph.D. theses and other student publications.     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.     

Effect of Thermal Treatment on CFRP Parts Before and After Adhesive Bonding

Numerous non-destructive techniques are being investigated for assuring quality of the adhesive bonds.The research presented here is focused on non-destructive assessment of carbon fibre reinforced polymer(CFRP)parts.The surface condition directly influences the performance of adhesive bonds.The structural joints should ensure safe usage of a structure.However,some modifications of the surface may lead to weak bond that cannot carry the desired load.This is why there is a search for methods of surface assessment before bonding.Moreover,reliable techniques are required to allow to verify the integrity of the adhesive bond after manufacturing or bonded repair.We focus on the laser induced fluorescence(LIF)method for assessing the surface state.The LIF is a noncontact measurement method.In the context of adhesive bond assessment the electromechanical impedance(EMI)method is studied.The EMI uses surface bonded piezoelectric sensors for excitation and sensing.The investigated samples were made of CFRP layers.The samples were treated at elevated temperatures.The influence of the thermal treatment was studied using LIF.The thermal treatment at 220℃could be clearly distinguishedrom the rest of the considered samples.The thermally treated plates were bonded to untreated plate and then they were measured with the EMI method to study the influence of the treatment on the adhesive bond.The changes of EMI spectra were significant for the treatment at 280 ℃ and for some thermally treated samples that were later contaminated with de-icing fluid.     

Mapping Regolith and Gossan for Mineral Exploration in the Eastern Kumaon Himalaya,India using hyperion data and object oriented image classification

Crystalline in the Kumaon Himalaya, India near Askot area is a prominent site of the base metal mineralization and gossanised surface. This area is hosted by the sulphides and sulphates of Cu, Pb, Zn and Au and Ag mineralization with the altered rocks like sericite chlorite schist, gneiss etc. Due to the deep weathering this area is also a good illustration site of the gossanised outcrop.     

Assessment study of ionosphere correction model using single- and multi-shell algorithms approach over sub-Saharan African region

It is a known fact that ionosphere is the largest and the least predictable among the sources of error limiting the reliability and accuracy of Global Navigation Satellite Systems (GNSS) and its regional augmentation systems like Satellite Based Augmentation System (SBAS) in a safety-of-life application. The situation becomes worse in the Equatorial Ionization Anomaly (EIA) region, where the daytime ionization distribution is modified by the fountain effect that develops a crest of electron density at around ±15° to ±20° of the magnetic equator and a trough at the magnetic equator during the local noon hours. Related to this phenomenon is the appearance of ionosphere irregularities and plasma bubbles after local sunset. These may degrade further the quality of service obtained from the GNSS/SBAS system of the said periods. Considering the present operational augmentation systems, the accuracy and integrity of the ionosphere corrections estimate decreases as the level of disturbances increases. In order to provide a correct ionosphere correction to the user of GNSS operating in African EIA region and meet the integrity requirements, a certified ionosphere correction model that accurately characterizes EIA gradient with the full capacity to over-bound the residual error will be needed. An irregularities detector and a decorrelation adaptor are essential in an algorithm usable for African sub-Saharan SBAS operation. The algorithm should be able to cater to the equatorial plasma vertical drifts, diurnal and seasonal variability of the ionosphere electron density and also should take into account the large spatial and temporal gradients in the region. This study presents the assessment of the ionosphere threat model with single and multi-layer algorithm, using modified planar fit and Kriging approaches.     

Mechanism of error propagation from the subdaily Universal Time model into the celestial pole offsets estimated by VLBI

Within the analysis of space geodetic observations, errors of the applied subdaily Earth rotation model can induce systematic effects in different estimated parameters. In this paper, we focus on the impact of the subdaily Universal Time (UT1) model on the celestial pole offsets (CPO) estimated from very long baseline interferometry (VLBI) observations. We provide a mechanism that describes the error propagation from the subdaily UT1 into the daily CPO.In typical 24-h VLBI sessions the observed quasars are well distributed over the sky. But the observations, if looked at from the Earth-fixed frame, are not homogeneously distributed. The amount of observations performed in different terrestrial directions shows an irregularity which can be roughly compared to the case where the observations are collected in only one Earth-fixed direction. This peculiarity leads to artefacts in VLBI solutions, producing a correlation between the subdaily variations in UT1 and the position of the celestial pole. As a result errors in diurnal terms of the subdaily UT1 model are partly compensated by the estimated CPO. We compute for each 24-h VLBI session from 1990 until 2011 the theoretical response of the CPO to an error in the subdaily UT1 by setting up a least-squares adjustment model and using as input the coordinates of the observed quasars and observation epochs. Then real observed response of the estimated CPO derived from the VLBI session solutions is compared to the predicted one. A very good agreement between the CPO values estimated from VLBI and the predicted values was achieved. The presented model of error propagation from the subdaily UT1 into the daily CPO allows to predict and explain the behaviour of CPO estimates of VLBI solutions computed with different subdaily Earth rotation models, what can be helpful for testing the accuracy of different subdaily tidal models.     

Fluctuations, Dissipation and Heating in the Corona

Mechanisms for the deposition of heat in the lower coronal plasma are discussed, emphasizing recent attempts to reconcile the fluid and kinetic perspectives. Structures at the MHD scales are believed to act as reservoirs for fluctuation energy, which in turn drive a nonlinear cascade process. Kinetic processes act at smaller spatial scales and more rapid time scales. Cascade-driven processes are contrasted with direct cyclotron absorption, and this distinction is echoed in the contrast between frequency and wavenumber spectra of the fluctuations. Observational constraints are also discussed, along with estimates of the relative efficiency of cascade and cyclotron processes. This revised version was published online in June 2006 with corrections to the Cover Date.