钯改性镍基高温合金铝化物涂层的组织和热腐蚀性能

以M38合金作基材，先电镀Pd-20wt%Ni合金，再采用传统低温高活性(LTHA)固渗铝工艺，用NaCl作活性剂渗铝制得Pd-Ni-Al涂层。XRD和EPMA分析结果表明，涂层为固溶Ni的β-PdAl单相结构；在900℃Na     

组合机床多轴箱计算机辅助设计系统

介绍利用ＡｏｔｏＣＡＤ二次开发工具ＯｂｊｅｃｔＡＲＸ３．０开发的组合机床多轴箱ＣＡＤ。阐述依据模块化原理设计系统的各个组成模块，以及由于采用ＶｉｓｕａｌＣ＋＋６．０可视化编程语言及微软ＭＦＣ基本类库，使程序界面的交互性比以往设计显著提高。     

某型号机襟翼机构摩擦磨损可靠性分析与计算(英文)

本文应用空间机构的建模方法建立了某型号机襟翼机构运动的数学模型。当给出输入参数时，可通过此数学模型求出襟翼机构的理论输出参数。输入参数相同时，通过引入摩擦磨损量至数学模型可获得襟翼机构的实际输出参数，并在此基础上求得襟翼机构的摩擦磨损可靠性。     

铁基金刚石节块的热处理及其耐磨性能研究

首次提出了在烧结型金刚石工具的制造中引入热处理的新工艺，并系统地研究了淬火温度、淬火时间及回火温度等热处理工艺参数对热压烧结型铁基金刚石圆盘锯节块及其胎体材料机械性能的影响，同时对经热处理的铁基金刚石圆盘锯节块在石材旺苍红上进行磨损试验研究。试验结果表明，热压烧结型铁基金刚石圆盘锯节块胎体热处理的最佳工艺参数为：淬火温度为７６０～７９０℃、淬火时间为３．５ｍｉｎ、回火温度为２４５～３１５℃；经热处理后铁基金刚石圆盘锯胎体及节块的强度、硬度等机械性能有显著的提高，热处理也能明显改善铁基金刚石圆盘锯节块的耐磨性能。这说明将热处理工艺用于烧结型金刚石工具的制造中是切实可行的。     

运动单站干涉仪相位差直接定位方法

针对传统干涉仪测向定位在低信噪比(SNR)下性能降低、多频段系统复杂等缺点,本文直接利用运动单站干涉仪模糊相位差(PD)实现对地面静止辐射源定位.为解决该定位问题,结合干涉仪相位差的几何特性,提出了一种多角度距离参数化高斯和滤波(MB-RP-GMF)定位解算方法,利用相位差误差检测获得多个初始方位角,通过距离参数化得到一组滤波初始值,采用扩展卡尔曼滤波(EKF)进行定位计算.仿真结果表明,该定位方法在低信噪比下优于仅测向(BO)定位,且仅采用一组干涉仪便可对多个频段辐射源进行定位.     

运输环境中某战术导弹结构振动特性分析

应用三维有限单元和导弹实体简化模型对一种战术导弹的结构振动特性进行分析，并动用ＡＮＳＹＳ有限元分析程序，计算得到了“自由－固支”条件下，导弹竖立状态的固有模态，取得了与试验和数据基本一致的结果，证明了所建模型物正确性，进而对运输环境中导弹水平支承条件下的固有频率和振型进行了分析计算，所得结果为导弹的使用可靠性分析提供了依据。     

A closed-form solution for moving source localization using LBI changing rate of phase difference only

Due to the deficiencies in the conventional multiple-receiver localization systems based on direction of arrival(DOA) such as system complexity of interferometer or array and amplitude/phase unbalance between multiple receiving channels and constraint on antenna configuration,a new radiated source localization method using the changing rate of phase difference(CRPD)measured by a long baseline interferometer(LBI) only is studied. To solve the strictly nonlinear problem, a two-stage closed-form solution is proposed. In the first stage, the DOA and its changing rate are estimated from the CRPD of each observer by the pseudolinear least square(PLS) method,and then in the second stage, the source position and velocity are found by another PLS minimization. The bias of the algorithm caused by the correlation between the measurement matrix and the noise in the second stage is analyzed. To reduce this bias, an instrumental variable(IV) method is derived. A weighted IV estimator is given in order to reduce the estimation variance. The proposed method does not need any initial guess and the computation is small. The Cramer–Rao lower bound(CRLB) and mean square error(MSE) are also analyzed. Simulation results show that the proposed method can be close to the CRLB with moderate Gaussian measurement noise.     

Optimization of beamforming and path planning for UAV-assisted wireless relay networks

Recently, unmanned aerial vehicles （UAVs） acting as relay platforms have attracted considerable attention due to the advantages of extending coverage and improving connectivity for long-range communications. Specifically, in the scenario where the access point （AP） is mobile, a UAV needs to find an efficient path to guarantee the connectivity of the relay link. Motivated by this fact, this paper proposes an optimal design for beamforming （BF） and UAV path planning. First of all, we study a dual-hop amplify-and-forward （AF） wireless relay network, in which a UAV is used as relay between a mobile AP and a fixed base station （BS）. In the network, both of the AP and the BS are equipped with multiple antennas, whereas the UAV has a single antenna. Then, we obtain the output signal~to-noise ratio （SNR） of the dual-hop relay network. Based on the criterion of maximizing the output SNR, we develop an optimal design to obtain the solution of the optimal BF weight vector and the UAV heading angle. Next, we derive the closed-form outage probability （OP） expression to investigate the performance of the dual-hop relay network conveniently. Finally, computer simulations show that the proposed approach can obtain nearly optimal flying path and OP performance, indicating the effectiveness of the proposed algorithm. Furthermore, we find that increasing the antenna number at the BS or the maximal heading angle can significantly improve the performance of the considered relay network.