表面涂层技术在航空发动机上的应用

介绍了保护、封严、密封、热障等涂层产品及其在航空发动机上的应用。这些涂层的应用提高了发动机可靠性 ,延长了发动机使用寿命     

Limits of flanging process feasibility to create thin-wall conical shells

In this paper, a process of flanging to create thin-walled axisymmetrical shells with the shape of truncated cone is analyzed. Also presented are some dependences that make it possible to determine the relative depth of a formed piece at the given piece-blank thickness ratio.     

Influence of the 27-day solar flux variations on the ionosphere parameters measured at Irkutsk in 2003–2005

We present an investigation of the influence of the 27-day solar flux variations, caused by solar rotation, on the ionosphere parameters such as the F2 layer critical frequency (foF2) and the total electron content (TEC). Our observational data were obtained with the Irkutsk Digisonde (DPS-4) located at 52.3 North and 104.3 East during the period from 2003 to 2005. In addition, we use TEC data from the Global Ionosphere Maps (GIM) based on Global Positioning System (GPS) satellites. The solar radiation flux at a wavelength of 10.7 cm (F10.7 index) is used as an index characterizing the solar activity level. A good correlation between observed ionosphere parameters and solar activity variations is found especially in autumn-to-winter season. We estimate the impact of the 27-day solar flux variations on the day-to-day variability and determine the time delay of the ionosphere response.     

高温天线罩材料研究进展

对目前主要几种高温天线罩材料体系，包括氧化铝陶瓷、石英陶瓷、微晶玻璃、纤维增强二氧化硅基复合材料、纤维增强磷酸盐基复合材料以及硅氧氮陶瓷材料的研究发展和应用情况进行了简要的综述。     

纳米复合搪瓷涂层在液体火箭发动机的应用研究

介绍了纳米复合搪瓷涂层的化学成份,涂层粉末粒度的比例、浆料的制备工艺及保存方法。重点论述了涂层在发动机不同零件上的浆料成份及粘度、涂覆方法、烧结温度和工艺过程。还介绍了对于不同材料成份与粒度配比涂层的各种检验内容与结果及在液体火箭发动机热试车的考验结果。     

Effect of non-uniform basic temperature gradient on the onset of Marangoni convection in a fluid with suspended particles

The effect of a non-uniform basic temperature gradient on the onset of convection driven by surface tension in a horizontal layer of a Boussinesq fluid with suspended particles confined between an upper free, constant heat flux boundary and a lower rigid isothermal boundary is considered. The microrotation is assumed to vanish at the boundaries. A linear stability analysis is performed. The Rayleigh–Ritz technique is used to obtain the eigenvalues. The influence of various parameters on the onset of convection has been analyzed. Six different non-uniform basic state temperature profiles are considered and their comparative influence on onset is discussed. It is observed that the fluid layer with suspended particles heated from below is more stable compared to the classical fluid layer without suspended particles. The problem has possible applications in microgravity situations.     

热氧、湿热和热水老化对T300/ BHEP 复合材料玻璃化转变温度的影响

通过对碳纤维/环氧复合材料(T300/BHEP)进行热氧、湿热和热水老化研究,得到了材料的质量变化率和Tg随老化条件的演变规律,分析了老化机理.结果表明:T300/BHEP复合材料在热氧老化条件下,因后固化和自由体积收缩,Tg升高;在湿热和热水老化条件下,因水分塑化作用和水对分子链间氢键的破坏,Tg降低.三种老化条件下,Tg与质量变化率均呈线性关系.对比80℃热氧、80℃/RH75%湿热和80℃热水老化条件下的结果,发现水分的塑化作用对Tg的影响要大于因热的作用产生的后固化,且湿度越大,Tg降低越明显.     

循环吸湿对炭纤维复合材料界面性能的影响

通过对炭纤维增强复合材料进行70、85、100℃下的循环水浸吸湿试验,研究了复合材料在不同水浸温度下的吸湿-脱湿行为规律。同时,对循环吸湿-脱湿过程中的试样进行层间剪切强度测试和动态力学性能测试,并结合扫描电镜观察循环吸湿各个阶段的纤维基体结合状态。结果表明,水浸温度越高,水分的扩散速率越快,饱和吸湿率越大。经过循环吸湿后复合材料的吸湿行为仍满足Fick第二定律,吸湿后层间剪切强度下降,湿热循环次数越多下降的越明显。脱湿后层间剪切强度有所恢复,水浸温度越高造成的不可逆破坏越大,层间剪切强度恢复的越少。干态时的玻璃化转变温度为231℃,吸湿后下降了37℃。     

抗氧化处理对3D C/C复合材料性能的影响

研究了采用化学气相反应法制备的SiC抗氧化涂层对3D整体编织C／C复合材料的密度、力学性能以及微观结构的影响。结果表明，3D C／C复合材料经抗氧化处理后，其密度、开孔率以及力学性能均有不同程度的提高。由SEM微观结构可以看出，其力学性能提高是由于气态Si渗入到材料基体内部，并与内部的C反应生成SiC，在一定程度上弥合了材料中的缺陷所致。     

高速铁路隧道初始压缩波一维流动模型的数值分析方法

基于隧道内空气流通截面是时间和距离的二元函数条件与一维流动理论,提出了高速列车驶入设有缓冲结构隧道端口时产生初始压缩波的数值分析方法。一维流动理论采用考虑摩擦、传热以及空气质交换等因素的一维可压缩非定常不等熵流动模型。数值分析方法采用广义黎曼变量特征线法。与国外有关未设缓冲结构、开孔型与未开孔型缓冲结构的隧道端口三种情况的现车试验结果进行了比较,表明本文所建方法正确、合理,能够模拟计算多种类型缓冲结构条件下的压缩波波动规律。