行政自由裁量权的道德边界

行政自由裁量权的正确行使,不仅离不开法律控制,而且需要设立道德边界。行政自由裁量权的道德边界,由行政主体在行政自由裁量中应当遵循的道德原则所构成。这样的道德原则主要有:平等裁量原则、公正裁量原则和据实裁量原则。行政自由裁量的道德原则,内化为行政主体的道德信念,就可以使行政主体自觉地控制其自由裁量行为。而公众舆论对于行政自由裁量过程的道德监督,则是实现行政自由裁量的道德原则内化的外部条件。     

Dynamics and de-spin control of massive target by single tethered space tug

This paper investigates the dynamics and de-spin control of a massive target by a single tethered space tug in the post-capture phase. The dynamic model of the tethered system is derived and simplified to a dimensionless form. Further, a decoupled PD controller is proposed, and the local stability of the controller is analyzed by linearization technique. Parametric studies of the dynamics and de-spin control of a massive target are conducted to characterize the dynamic process of de-spin with the proposed control law. It is shown that the massive target can be de-span by a single and small space tug with limited thrust within finite time. The thrust tangent with the tether de-spins the target while the thrust normal to the tether prevents the tether from winding up the target. The tether length has a positive contribution to the de-spin of a target. The longer tether leads to a faster de-spin process.     

An evolutionary computational framework for capacity-safety trade-off in an air transportation network

Airspace safety and airport capacity are two key challenges to sustain the growth in Air Transportation. In this paper, we model the Air Transportation Network as two sub-networks of airspace and airports, such that the safety and capacity of the overall Air Transportation network emerge from the interaction between the two. We propose a safety-capacity trade-off approach,using a computational framework, where the two networks can inter-act and the trade-off between capacity and safety in an Air Transport Network can be established. The framework comprise of an evolutionary computation based air traffic scenario generation using a flow capacity estimation module(for capacity), Collision risk estimation module(for safety) and an air traffic simulation module(for evaluation). The proposed methodology to evolve air traffic scenarios such that it minimizes collision risk for given capacity estimation was tested on two different air transport network topologies(random and small-world) with the same number of airports. Experimental results indicate that though airspace collision risk increases almost linearly with the increasing flow(flow intensity) in the corresponding airport network, the critical flow depend on the underlying network configuration. It was also found that, in general, the capacity upper bound depends not only on the connectivity among airports and their individual performances but also the configuration of waypoints and mid-air interactions among conflicts. Results also show that airport network can accommodate more traffic in terms of capacity but the corresponding airspace network cannot accommodate the resulting traffic flow due to the bounds on collision risk.     

低排放燃烧室NO_x排放试验及预测方法研究

为了研究中心分级贫油低排放燃烧室的排放特性和排放预测方法,针对一个低排放头部方案,在单头部燃烧室试验件上,在不同的温度、压力、油气比、供油模式和分级比条件下,测量其排放性能。以Lefebvre排放经验预测公式为基础,采用经验分析方法拟合排放试验数据,归纳出适用于本头部方案的排放预测公式。表征预测好坏的判定系数R2在小工况下和大工况下分别为0.95和0.93,表明预测结果与试验结果符合度较好。小工况和大工况排放特性不同,对仅预燃级喷油的小工况工作模式,NO_x排放主要受化学恰当燃烧温度和预燃级局部当量比的影响;对预燃级和主燃级同时喷油的大工况工作模式,NO_x排放主要受燃烧区温度和主燃级燃油比例的影响。     

纳米复合镍粉雷达吸波涂层研究

采用机械化学法将纳米SiC包覆在镍粉表面制备复合吸波材料,将该材料喷涂在基体上制备吸波涂层,并研究了SiC在复合材料中的含量变化对涂层吸波性能的影响.研究表明,SiC含量为10%时,纳米复合涂层的吸波性能最佳.与镍粉吸波涂层相比,该纳米复合涂层中频段的吸波性能明显提高,发射率小于-5 dB的带宽由7 GHz增加到10.4 GHz,涂层最高吸收值达到-23.4 dB.     

TC11合金高温变形行为及其机理

采用Gleeble-1500热模拟机研究了TC11合金在800～1 050℃、应变速率0.005～5/s条件下的高温变形行为.根据动力学分析,确定了不同温度区间的热激活能和热变形方程.结合变形微观组织观察确定了TC11合金的高温变形机制.结果显示:TC11合金在(α β)两相区和β相区的热变形激活能分别为285.38和141.98 kJ/mol,表明不同温度区间的热变形机理不同;在两相区变形主要发生片状组织的球化,在β相区变形时低应变速率下(0.005～0.05/s)主要发生β相的动态再结晶,高应变速率下(0.05～5/s)主要发生动态回复.研究结果为确定该合金的最佳变形工艺参数提供了理论依据.     

AZ91镁合金搅拌摩擦加工后的组织与性能

采用400rpm-100mm/min,800rpm-100mm/min,800rpm-200mm/min三种工艺参数对铸态AZ91镁合金进行搅拌摩擦加工(FSP)处理,并对合金加工前后的显微组织和拉伸性能及微观断裂机制进行分析。结果表明,经800rpm-100mm/min工艺FSP处理后,合金的显微组织明显细化,延伸率和抗拉强度显著提高,综合拉伸性能最好,且拉伸断口主要表现为韧性断裂的特征。这主要是由于在FSP过程中合金发生动态再结晶,使合金晶粒显著细化及粗大β相的溶解和破碎所致。